linux.git/drivers/dma/idxd, branch v5.9

dmaengine: idxd: reset states after device disable or reset

2020-08-17T04:55:04+00:00

The state for WQs should be reset to disabled when a device is reset or
disabled.

Fixes: da32b28c95a7 ("dmaengine: idxd: cleanup workqueue config after disabling")
Reported-by: Mona Hossain 
Signed-off-by: Dave Jiang 
Link: https://lore.kernel.org/r/159586777684.27150.17589406415773568534.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul

Merge branch 'for-linus' into fixes

2020-08-05T13:32:07+00:00

Signed-off-by: Vinod Koul 

 Conflicts:
	drivers/dma/idxd/sysfs.c

dmaengine: idxd: move idxd interrupt handling to mask instead of ignore

2020-07-13T09:18:02+00:00

Switch driver to use MSIX mask and unmask instead of the ignore bit.
When ignore bit is cleared, we must issue an MMIO read to ensure writes
have all arrived and check and process any additional completions. The
ignore bit does not queue up any pending MSIX interrupts. The mask bit
however does. Use API call from interrupt subsystem to mask MSIX
interrupt since the hardware does not have convenient mask bit register.

Suggested-by: Ashok Raj 
Signed-off-by: Dave Jiang 
Link: https://lore.kernel.org/r/159319517621.70410.11816465052708900506.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul

dmaengine: idxd: add work queue drain support

2020-07-13T09:18:02+00:00

Add wq drain support. When a wq is being released, it needs to wait for
all in-flight operation to complete.  A device control function
idxd_wq_drain() has been added to facilitate this. A wq drain call
is added to the char dev on release to make sure all user operations are
complete. A wq drain is also added before the wq is being disabled.

A drain command can take an unpredictable period of time. Interrupt support
for device commands is added to allow waiting on the command to
finish. If a previous command is in progress, the new submitter can block
until the current command is finished before proceeding. The interrupt
based submission will submit the command and then wait until a command
completion interrupt happens to complete. All commands are moved to the
interrupt based command submission except for the device reset during
probe, which will be polled.

Fixes: 42d279f9137a ("dmaengine: idxd: add char driver to expose submission portal to userland")
Signed-off-by: Dave Jiang 
Reviewed-by: Tony Luck 
Reviewed-by: Dan Williams 
Link: https://lore.kernel.org/r/159319502515.69593.13451647706946040301.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul

dmaengine: idxd: fix misc interrupt handler thread unmasking

2020-07-02T13:32:20+00:00

Fix unmasking of misc interrupt handler when completing normal. It exits
early and skips the unmasking with the current implementation. Fix to
unmask interrupt when exiting normally.

Fixes: bfe1d56091c1 ("dmaengine: idxd: Init and probe for Intel data accelerators")
Signed-off-by: Dave Jiang 
Link: https://lore.kernel.org/r/159311256528.855.11527922406329728512.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul

dmaengine: idxd: cleanup workqueue config after disabling

2020-07-02T13:32:19+00:00

After disabling a device, we should clean up the internal state for
the wqs and zero out the configuration registers. Without doing so can cause
issues when the user reprogram the wqs.

Fixes: c52ca478233c ("dmaengine: idxd: add configuration component of driver")
Reported-by: Yixin Zhang 
Signed-off-by: Dave Jiang 
Tested-by: Yixin Zhang 
Link: https://lore.kernel.org/r/159311264246.1198.11955791213681679428.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul

dmaengine: idxd: move submission to sbitmap_queue

2020-06-24T07:25:09+00:00

Kill the percpu-rwsem for work submission in favor of an sbitmap_queue.

Signed-off-by: Dave Jiang 
Reviewed-by: Tony Luck 
Reviewed-by: Dan Williams 
Link: https://lore.kernel.org/r/159225446631.68253.8860709181621260997.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul

dmaengine: idxd: fix cdev locking for open and release

2020-06-24T05:47:46+00:00

add the wq lock in cdev open and release call. This fixes
race conditions observed in the open and close routines.

Fixes: 42d279f9137a ("dmaengine: idxd: add char driver to expose submission portal to userland")
Signed-off-by: Nikhil Rao 
Signed-off-by: Dave Jiang 
Link: https://lore.kernel.org/r/159285824892.64944.2905413694915141834.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul

dmaengine: cookie bypass for out of order completion

2020-06-17T14:15:14+00:00

The cookie tracking in dmaengine expects all submissions completed in
order. Some DMA devices like Intel DSA can complete submissions out of
order, especially if configured with a work queue sharing multiple DMA
engines. Add a status DMA_OUT_OF_ORDER that tx_status can be returned for
those DMA devices. The user should use callbacks to track the completion
rather than the DMA cookie. This would address the issue of dmatest
complaining that descriptors are "busy" when the cookie count goes
backwards due to out of order completion. Add DMA_COMPLETION_NO_ORDER
DMA capability to allow the driver to flag the device's ability to complete
operations out of order.

Reported-by: Swathi Kovvuri 
Signed-off-by: Dave Jiang 
Tested-by: Swathi Kovvuri 
Link: https://lore.kernel.org/r/158939557151.20335.12404113976045569870.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul

Merge tag 'dmaengine-5.8-rc1' of git://git.infradead.org/users/vkoul/slave-dma

2020-06-10T18:03:04+00:00

Pull dmaengine updates from Vinod Koul:
 "A fairly small dmaengine update which includes mostly driver updates
  (dmatest, dw-edma, ioat, mmp-tdma and k3-udma) along with Renesas
  binding update to json-schema"

* tag 'dmaengine-5.8-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (39 commits)
  dmaengine: imx-sdma: initialize all script addresses
  dmaengine: ti: k3-udma: Use proper return code in alloc_chan_resources
  dmaengine: ti: k3-udma: Remove udma_chan.in_ring_cnt
  dmaengine: ti: k3-udma: Add missing dma_sync call for rx flush descriptor
  dmaengine: at_xdmac: Replace zero-length array with flexible-array
  dmaengine: at_hdmac: Replace zero-length array with flexible-array
  dmaengine: qcom: bam_dma: Replace zero-length array with flexible-array
  dmaengine: ti: k3-udma: Use PTR_ERR_OR_ZERO() to simplify code
  dmaengine: moxart-dma: Drop pointless static qualifier in moxart_probe()
  dmaengine: sf-pdma: Simplify the error handling path in 'sf_pdma_probe()'
  dmaengine: qcom_hidma: use true,false for bool variable
  dmaengine: dw-edma: support local dma device transfer semantics
  dmaengine: Fix doc strings to satisfy validation script
  dmaengine: Include dmaengine.h into dmaengine.c
  dmaengine: dmatest: Describe members of struct dmatest_info
  dmaengine: dmatest: Describe members of struct dmatest_params
  dmaengine: dmatest: Allow negative timeout value to specify infinite wait
  Revert "dmaengine: dmatest: timeout value of -1 should specify infinite wait"
  dmaengine: stm32-dma: direct mode support through device tree
  dt-bindings: dma: add direct mode support through device tree in stm32-dma
  ...