Adjust indentation from spaces to tab (+optional two spaces) as in coding style with command like: $ sed -e 's/^ /\t/' -i */Kconfig Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/1574306348-29212-1-git-send-email-krzk@kernel.org Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add PDMA driver, sf-pdma, to enable DMA engine on HiFive Unleashed Rev A00 board. - Implement dmaengine APIs, support MEM_TO_MEM async copy. - Tested by DMA Test client - Supports 4 channels DMA, each channel has 1 done and 1 err interrupt connected to platform-level interrupt controller (PLIC). - Depends on DMA_ENGINE and DMA_VIRTUAL_CHANNELS The datasheet is here: https://static.dev.sifive.com/FU540-C000-v1.0.pdf Follow the DMAengine controller doc, "./Documentation/driver-api/dmaengine/provider.rst" to implement DMA engine. And use the dma test client in doc, "./Documentation/driver-api/dmaengine/dmatest.rst", to test. Each DMA channel has separate HW regs and support done and error ISRs. 4 channels share 1 done and 1 err ISRs. There's no expander/arbitrator in DMA HW. ------ ------ | |--< done 23 >--|ch 0| | |--< err 24 >--| | (dma0chan0) | | ------ | | ------ | |--< done 25 >--|ch 1| | |--< err 26 >--| | (dma0chan1) |PLIC| ------ | | ------ | |--< done 27 >--|ch 2| | |--< err 28 >--| | (dma0chan2) | | ------ | | ------ | |--< done 29 >--|ch 3| | |--< err 30 >--| | (dma0chan3) ------ ------ Signed-off-by: Green Wan <green.wan@sifive.com> Link: https://lore.kernel.org/r/20191107084955.7580-4-green.wan@sifive.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for AXI Multichannel Direct Memory Access (AXI MCDMA) core, which is a soft Xilinx IP core that provides high-bandwidth direct memory access between memory and AXI4-Stream target peripherals. The AXI MCDMA core provides scatter-gather interface with multiple independent transmit and receive channels. The driver supports device_prep_slave_sg slave transfer mode. Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com> Link: https://lore.kernel.org/r/1571763622-29281-7-git-send-email-radhey.shyam.pandey@xilinx.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
Driver for Socionext Milbeaut XDMAC controller. The controller only supports Mem-To-Mem transfers over upto 8 configurable channels. Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org> Link: https://lore.kernel.org/r/20191015033219.14713-1-jassisinghbrar@gmail.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
Driver for Socionext Milbeaut HDMAC controller. The controller has upto 8 floating channels, that need a predefined slave-id to work from a set of slaves. Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org> Link: https://lore.kernel.org/r/20191015033359.14925-1-jassisinghbrar@gmail.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
DPPA2(Data Path Acceleration Architecture 2) qDMA supports virtualized channel by allowing DMA jobs to be enqueued into different work queues. Core can initiate a DMA transaction by preparing a frame descriptor(FD) for each DMA job and enqueuing this job through a hardware portal. DPAA2 components can also prepare a FD and enqueue a DMA job through a hardware portal. The qDMA prefetches DMA jobs through DPAA2 hardware portal. It then schedules and dispatches to internal DMA hardware engines, which generate read and write requests. Both qDMA source data and destination data can be either contiguous or non-contiguous using one or more scatter/gather tables. The qDMA supports global bandwidth flow control where all DMA transactions are stalled if the bandwidth threshold has been reached. Also supported are transaction based read throttling. Add NXP dppa2 qDMA to support some of Layerscape SoCs. such as: LS1088A, LS208xA, LX2, etc. Signed-off-by: Peng Ma <peng.ma@nxp.com> Link: https://lore.kernel.org/r/20190930020440.7754-2-peng.ma@nxp.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull MIPS updates from Paul Burton:
"Main MIPS changes:
- boot_mem_map is removed, providing a nice cleanup made possible by
the recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs
or MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of
Vincenzo Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic
SoCs.
- pte_special() is now supported for some configurations, allowing
among other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil,
mostly enabled by the inclusion of the new TCU (timer-counter unit)
drivers he's spent a very patient year or so working on. Plus some
fixes for X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems"
* tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (89 commits)
MIPS: Detect bad _PFN_SHIFT values
MIPS: Disable pte_special() for MIPS32 with RiXi
MIPS: ralink: deactivate PCI support for SOC_MT7621
mips: compat: vdso: Use legacy syscalls as fallback
MIPS: Drop Loongson _CACHE_* definitions
MIPS: tlbex: Remove cpu_has_local_ebase
MIPS: tlbex: Simplify r3k check
MIPS: Select R3k-style TLB in Kconfig
MIPS: PCI: refactor ioc3 special handling
mips: remove ioremap_cachable
mips/atomic: Fix smp_mb__{before,after}_atomic()
mips/atomic: Fix loongson_llsc_mb() wreckage
mips/atomic: Fix cmpxchg64 barriers
MIPS: Octeon: remove duplicated include from dma-octeon.c
firmware: bcm47xx_nvram: Allow COMPILE_TEST
firmware: bcm47xx_nvram: Correct size_t printf format
MIPS: Treat Loongson Extensions as ASEs
MIPS: Remove dev_err() usage after platform_get_irq()
MIPS: dts: mscc: describe the PTP ready interrupt
MIPS: dts: mscc: describe the PTP register range
...
Pull dmaengine updates from Vinod Koul: - Move Dmaengine DT bindings to YAML and convert Allwinner to schema. - FSL dma device_synchronize implementation - DW split acpi and of helpers and updates to driver and support for Elkhart Lake - Move filter fn as private for omap-dma and edma drivers and improvements to these drivers - Mark expected switch fall-through in couple of drivers - Renames of shdma and nbpfaxi binding document - Minor updates to bunch of drivers * tag 'dmaengine-5.4-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (55 commits) dmaengine: ti: edma: Use bitmap_set() instead of open coded edma_set_bits() dmaengine: ti: edma: Only reset region0 access registers dmaengine: ti: edma: Do not reset reserved paRAM slots dmaengine: iop-adma.c: fix printk format warning dmaengine: stm32-dma: Use struct_size() helper dt-bindings: dmaengine: dma-common: Fix the dma-channel-mask property dmanegine: ioat/dca: Use struct_size() helper dmaengine: iop-adma: remove set but not used variable 'slots_per_op' dmaengine: dmatest: Add support for completion polling dmaengine: ti: omap-dma: Remove variable override in omap_dma_tx_status() dmaengine: ti: omap-dma: Remove 'Assignment in if condition' dmaengine: ti: edma: Remove 'Assignment in if condition' dmaengine: dw: platform: Split OF helpers to separate module dmaengine: dw: platform: Split ACPI helpers to separate module dmaengine: dw: platform: Move handle check to dw_dma_acpi_controller_register() dmaengine: dw: platform: Switch to acpi_dma_controller_register() dmaengine: dw: platform: Use devm_platform_ioremap_resource() dmaengine: dw: platform: Enable iDMA 32-bit on Intel Elkhart Lake dmaengine: dw: platform: Use struct dw_dma_chip_pdata dmaengine: dw: Export struct dw_dma_chip_pdata for wider use ...
Pull ARM SoC platform updates from Arnd Bergmann: "The main change this time around is a cleanup of some of the oldest platforms based on the XScale and ARM9 CPU cores, which are between 10 and 20 years old. The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel IOP33x/IOP13xx platforms are removed after we determined that nobody is using them any more. The TI Davinci and NXP LPC32xx platforms on the other hand are still in active use and are converted to the ARCH_MULTIPLATFORM build, meaning that we can compile a kernel that works on these along with most other ARMv5 platforms. Changes toward that goal are also merged for IOP32x, but additional work is needed to complete this. Patches for the remaining ARMv5 platforms have started but need more work and some testing. Support for the new ASpeed AST2600 gets added, this is based on the Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and ARMv6 chips in the same family. Other changes include a cleanup of the ST-Ericsson ux500 platform and the move of the TI Davinci platform to a new clocksource driver" [ The changes had marked INTEL_IOP_ADMA and USB_LPC32XX as being buildable on other platforms through COMPILE_TEST, but that causes new warnings that I most definitely do not want to see during the merge window as that could hide other issues. So the COMPILE_TEST option got disabled for them again - Linus ] * tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits) ARM: multi_v5_defconfig: make DaVinci part of the ARM v5 multiplatform build ARM: davinci: support multiplatform build for ARM v5 arm64: exynos: Enable exynos-chipid driver ARM: OMAP2+: Delete an unnecessary kfree() call in omap_hsmmc_pdata_init() ARM: OMAP2+: move platform-specific asm-offset.h to arch/arm/mach-omap2 ARM: davinci: dm646x: Fix a typo in the comment ARM: davinci: dm646x: switch to using the clocksource driver ARM: davinci: dm644x: switch to using the clocksource driver ARM: aspeed: Enable SMP boot ARM: aspeed: Add ASPEED AST2600 architecture ARM: aspeed: Select timer in each SoC dt-bindings: arm: cpus: Add ASPEED SMP ARM: imx: stop adjusting ar8031 phy tx delay mailmap: map old company name to new one @microchip.com MAINTAINERS: at91: remove the TC entry MAINTAINERS: at91: Collect all pinctrl/gpio drivers in same entry ARM: at91: move platform-specific asm-offset.h to arch/arm/mach-at91 MAINTAINERS: Extend patterns for Samsung SoC, Security Subsystem and clock drivers ARM: s3c64xx: squash samsung_usb_phy.h into setup-usb-phy.c ARM: debug-ll: Add support for r7s9210 ...
Now that iop3xx and iop13xx are gone, the iop-adma driver no longer needs to deal with incompatible register layout defined in machine specific header files. Move the iop32x specific definitions into drivers/dma/iop-adma.h and the platform_data into include/linux/platform_data/dma-iop32x.h, and change the machine code to no longer reference those. The DMA0_ID/DMA1_ID/AAU_ID macros are required as part of the platform data interface and still need to be visible, so move those from one header to the other. Link: https://lore.kernel.org/r/20190809163334.489360-4-arnd@arndb.de Signed-off-by: Arnd Bergmann <arnd@arndb.de>