Pull pci updates from Bjorn Helgaas:
 "Enumeration:

   - Remove MPS/MRRS Kconfig settings (CONFIG_PCIE_BUS_*) that worked
     around a WiFi device defect; use a quirk or boot-time
     "pci=pcie_bus_tune_*" kernel parameter instead (Bjorn Helgaas)

   - Always lift 2.5GT/s restriction in PCIe failed link retraining to
     avoid clamping a link to 2.5GT/s after hot-plug changes the device
     (Maciej W. Rozycki)

   - Request bus reassignment when not probe-only to fix an enumeration
     regression on Marvell CN106XX and possibly other DT-based systems
     (Ratheesh Kannoth)

   - Fix procfs race between pci_proc_init() and pci_bus_add_device()
     that resulted in 'proc_dir_entry ... already registered' warnings
     and pointer corruption (Krzysztof Wilczyński)

   - Fix sysfs race that causes 'duplicate filename' warnings and boot
     panics by converting PCI resource files to static attributes
     (Krzysztof Wilczyński)

   - Expose sysfs 'resourceN_resize' attributes only on platforms with
     PCI mmap (Krzysztof Wilczyński)

   - Require CAP_SYS_ADMIN to write to sysfs 'resourceN_resize'
     attributes (Krzysztof Wilczyński)

   - Add security_locked_down(LOCKDOWN_PCI_ACCESS) to alpha PCI resource
     mmap path to match the generic path (Krzysztof Wilczyński)

   - Use kstrtobool() to parse the 'rom' attribute input to avoid the
     unexpected behavior of enabling the ROM when writing '0' with no
     trailing newline (Krzysztof Wilczyński)

  Resource management:

   - Improve resource claim logging for debuggability (Ilpo Järvinen)

   - Clean up several uses of const parameters (Ilpo Järvinen)

   - Check option ROM header signatures and lengths before accessing to
     avoid page faults and alignment faults (Guixin Liu)

  ASPM:

   - Don't reconfigure ASPM when entering low-power D-state; only do it
     when returning back to D0 (Carlos Bilbao)

  Power management:

   - During suspend, set power state to 'unknown' for all devices, not
     just those with drivers (Lukas Wunner)

   - Skip restoring Resizable BARs and VF Resizable BARs if device
     doesn't respond to config reads, to avoid invalid array accesses
     (Marco Nenciarini)

   - Add pci_suspend_retains_context() so drivers can tell whether
     devices retain internal state across suspend/resume, since some
     platforms reset devices on suspend; use this in nvme to avoid
     issues on Qcom RCs (Manivannan Sadhasivam)

  Power control:

   - Only to power on/off devices that actually support power control to
     avoid poking at incompatible devices mentioned in DT (Manivannan
     Sadhasivam)

  Virtualization and resets:

   - Log device readiness timeouts as errors, not warnings, because the
     device is likely unusable in this case (Bjorn Helgaas)

   - Wait for device readiness after soft reset (D3hot ->
     D0uninitialized transition), when the device may respond with
     Request Retry Status (RRS) if it needs more time to initialize
     (Bjorn Helgaas)

   - Drop unnecessary retries when restoring BARs because resets should
     now already include all required delays (Lukas Wunner)

   - Avoid FLR for MediaTek MT7925 WiFi, where FLR fails after a VM
     terminates uncleanly (Jose Ignacio Tornos Martinez)

   - Avoid SBR for Qualcomm WCN6855/WCN7850 WiFi, SDX62/SDX65 modems,
     which seem not to support it correctly (Jose Ignacio Tornos
     Martinez)

  Peer-to-peer DMA:

   - Prevent P2PDMA as well as CPU access to non-mappable BARs, e.g.,
     s390 ISM BARs (Matt Evans)

   - Add Intel QAT, DSA, IAA devices to whitelist (Lukas Wunner)

  Endpoint framework:

   - Add endpoint controller APIs for use by function drivers to
     discover auxiliary blocks like DMA engines (Koichiro Den)

   - Remember DesignWare eDMA engine base/size and expose them via the
     EPC aux-resource API (Koichiro Den)

   - Add endpoint embedded doorbell fallback, used if MSI allocation
     fails (Koichiro Den)

   - Validate BAR index and remove dead BAR read in endpoint doorbell
     test (Carlos Bilbao)

   - Unwind MSI/MSI-X vectors if NTB initialization fails part-way
     through (Koichiro Den)

   - Cache sleepable pci_irq_vector() value at ISR setup to avoid
     calling it from hardirq context (Koichiro Den)

   - Call sleepable pci_epc_raise_irq() from a work item instead of
     atomic context, e.g., when setting bits in NTB peer doorbells in
     the ntb_peer_db_set() path (Koichiro Den)

   - Report 0-based vNTB doorbell vector to account for link event 0 and
     historically skipped slot 1 (Koichiro Den)

   - Prevent configfs writes to vNTB db_count and other values that are
     already in use after EPC attach (Koichiro Den)

   - Account for vNTB db_valid reserved slots (link event 0 and
     historically skipped slot 1) so they don't appear as valid
     doorbells (Koichiro Den)

   - Implement vNTB .db_vector_count()/mask() for doorbells so clients
     can use multiple vectors and avoid thundering herds (Koichiro Den)

   - Report 0-based NTB doorbell vector to account for link event 0 and
     historically skipped slot 1 (Koichiro Den)

   - Fix doorbell bitmask and IRQ vector handling to clear only
     specified bits, use the correct vector for non-contiguous Linux IRQ
     numbers, and validate incoming vectors (Koichiro Den)

   - Implement NTB .db_vector_count()/mask() for doorbells so clients
     can use multiple vectors (Koichiro Den)

  Native PCIe controller infrastructure:

   - Add pci_host_common_link_train_delay() for the mandatory delay
     after > 5GT/s Link training completes and use it for cadence HPA,
     j721e, LGA; dwc; aardvark, mediatek-gen3, rzg3s (Hans Zhang)

   - Protect root bus removal with rescan lock in altera, brcmstb,
     cadence, dwc, iproc, mediatek, plda, rockchip to prevent
     use-after-free or crashes when racing with sysfs rescan or hotplug
     (Hans Zhang)

   - Add pci_host_common_parse_ports() for use by any native driver to
     parse Root Port properties (per-Link features like width, speed,
     PHY, power and reset control, etc should be described in Root Port
     stanzas, not the host bridge; currently only reset GPIOs
     implemented) (Sherry Sun)

  New native PCIe controller drivers:

   - Add DT binding and driver for UltraRISC DP1000 PCIe controller
     (Xincheng Zhang, Jia Wang)

  Altera PCIe controller driver:

   - Do not dispose of the parent IRQ mapping, which belongs to the
     parent interrupt controller (Mahesh Vaidya)

   - Fix chained IRQ handler ordering issue and resource leaks on probe
     failure (Mahesh Vaidya)

  AMD MDB PCIe controller driver:

   - Assert PERST# on shutdown so any connected Endpoints are held in
     reset during shutdown (Sai Krishna Musham)

  Amlogic Meson PCIe controller driver:

   - Propagate devm_add_action_or_reset() failure to fix probe error
     path (Shuvam Pandey)

   - Add .remove() callback to deinitialize the host bridge and power
     off the PHY (Shuvam Pandey)

  Broadcom iProc PCIe controller driver:

   - Restore .map_irq() assignment; its removal broke INTx on the iproc
     platform bus driver (Mark Tomlinson)

  Broadcom STB PCIe controller driver:

   - No change, but products using certain WiFi devices may be affected
     by removal of CONFIG_PCIE_BUS_* (see above)

  Freescale i.MX6 PCIe controller driver:

   - Move IMX6SX_GPR12_PCIE_TEST_POWERDOWN handling into the core reset
     functions (Richard Zhu)

   - Assert PERST# before enabling regulators to ensure that even if
     power is enabled, endpoint stays inactive until REFCLK is stable
     (Sherry Sun)

   - Parse reset properties in Root Port nodes (falling back to host
     bridge) to help support Key E connectors and the pwrctrl framework
     (Sherry Sun)

   - Configure i.MX95 REF_USE_PAD before PHY reset (Richard Zhu)

   - Assert i.MX95 ref_clk_en after reference clock stabilizes (Richard
     Zhu)

   - Integrate new pwrctrl API for DTs with Root Port-level power
     supplies (Sherry Sun)

  Intel Gateway PCIe controller driver:

   - Enable clock before PHY init for correct ordering (Florian Eckert)

   - Add .start_link() callback so the driver works again (Florian
     Eckert)

   - Stop overwriting the ATU base address discovered by
     dw_pcie_get_resources() (Florian Eckert)

   - Add DT 'atu' region since this is hardware-specific, and fall back
     to driver default if lacking (Florian Eckert)

  Loongson PCIe controller driver:

   - Ignore downstream devices only on internal bridges to avoid
     Loongson hardware issue (Rong Zhang)

   - Quirk old Loongson-3C6000 bridges that advertise incorrect
     supported link speeds (Ziyao Li)

  Marvell MVEBU PCIe controller driver:

   - Use fixed-width interrupt masks to avoid truncation in 64-bit
     builds (Rosen Penev)

  MediaTek PCIe controller driver:

   - Use FIELD_PREP() to fix incorrect operator precedence in
     PCIE_FTS_NUM_L0 (Li RongQing)

   - Fix IRQ domain leak when port fails to enable (Manivannan
     Sadhasivam)

   - Use actual physical address for MSI message address instead of
     virt_to_phys() (Manivannan Sadhasivam)

   - Add EcoNet EN7528 to DT binding (Caleb James DeLisle)

  MediaTek PCIe Gen3 controller driver:

   - Deassert PCIE_PHY_RSTB so REFCLK is stable for at least 100ms
     (PCIE_T_PVPERL_MS) before deasserting PERST# (Jian Yang)

   - Add .shutdown() to assert PERST# before powering down device (Jian
     Yang)

   - Do full device power down on removal, including asserting PERST#,
     when removing driver (Chen-Yu Tsai)

   - Fix a 'failed to create pwrctrl devices' error message that was
     inadvertently skipped (Chen-Yu Tsai)

  NVIDIA Tegra194 PCIe controller driver:

   - Program the DesignWare PORT_AFR L1 entrance latency based on the
     'aspm-l1-entry-delay-ns' DT property (Manikanta Maddireddy)

  Qualcomm PCIe controller driver:

   - Add Eliza SoC compatible in DT binding (Krishna Chaitanya Chundru)

   - Set max OPP during resume so DBI register accesses don't fail with
     NoC errors (Qiang Yu)

   - Add pci_host_common_d3cold_possible() to determine whether
     downstream devices are already in D3hot and wakeup-enabled devices
     are capable of generating PME from D3cold (Krishna Chaitanya
     Chundru)

   - Add .get_ltssm() callback to get the LTSSM status without DBI,
     since DBI may be inaccessible after PME_Turn_Off (Krishna Chaitanya
     Chundru)

   - Power down PHY via PARF_PHY_CTRL before disabling rails/clocks to
     avoid power leakage (Krishna Chaitanya Chundru)

   - Decide whether suspend should put the link in L2 and power down
     using pci_host_common_d3cold_possible() instead of checking whether
     ASPM L1 is enabled (Krishna Chaitanya Chundru)

   - Add qcom D3cold support to tear down interconnect bandwidth and OPP
     votes (Krishna Chaitanya Chundru)

   - Handle unsupported mixed PERST#/PHY DT configurations, e.g., PHY in
     RP node while PERST# is in the RC node, but warn about the DT issue
     (Qiang Yu)

   - Program T_POWER_ON based on DT 't-power-on-us' property in case
     hardware advertises incorrect values (Krishna Chaitanya Chundru)

   - Disable ASPM L0s for SA8775P (Shawn Guo)

   - Initialize DWC MSI lock for firmware-managed ECAM hosts, which
     don't use the dw_pcie_host_init() path that initializes the lock
     (Yadu M G)

  Renesas RZ/G3S PCIe controller driver:

   - Add RZ/V2N DT support (Lad Prabhakar)

  SOPHGO PCIe controller driver:

   - Add 'dma-coherent' DT property for sg2042-pcie driver (Han Gao)

  Synopsys DesignWare PCIe controller driver:

   - Apply ECRC TLP Digest workaround for all DesignWare cores prior to
     5.10a, not just 4.90a and 5.00a (Manikanta Maddireddy)

   - Use common struct dw_pcie 'mode' rather than duplicating it in
     artpec6, dra7xx, dwc-pcie, and keembay driver structs (Hans Zhang)

   - Use DEFINE_SHOW_ATTRIBUTE for ltssm_status debugfs to reduce
     boilerplate and fix a seq_file memory leak by including a
     .release() callback (Hans Zhang)

   - Fix a signedness bug in fault injection test code (Dan Carpenter)

   - Avoid NULL pointer dereference when tearing down debugfs for
     controller that lacks RAS DES capability (Shuvam Pandey)

  MicroSemi Switchtec management driver:

   - Add Gen6 Device IDs (Ben Reed)

  Miscellaneous:

   - Remove unused gpio.h include from amd-mdb, designware-plat, fu740,
     visconti drivers (Andy Shevchenko)

   - Fix typos in documentation (josh ziegler)

   - Use FIELD_MODIFY() instead of open-coding it (Hans Zhang)"

* tag 'pci-v7.2-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (168 commits)
  PCI/sysfs: Use kstrtobool() to parse the ROM attribute input
  PCI/sysfs: Limit BAR resize attribute scope to platforms with PCI mmap
  PCI/sysfs: Remove pci_create_legacy_files() and pci_sysfs_init()
  PCI/sysfs: Convert legacy I/O and memory attributes to static definitions
  PCI/sysfs: Add __weak pci_legacy_has_sparse() helper
  alpha/PCI: Compute legacy size in pci_mmap_legacy_page_range()
  PCI: Add macros for legacy I/O and memory address space sizes
  PCI/sysfs: Remove pci_{create,remove}_sysfs_dev_files()
  alpha/PCI: Convert resource files to static attributes
  alpha/PCI: Add static PCI resource attribute macros
  alpha/PCI: Remove WARN from __pci_mmap_fits() and __legacy_mmap_fits()
  alpha/PCI: Fix __pci_mmap_fits() overflow for zero-length BARs
  alpha/PCI: Use PCI resource accessor macros
  alpha/PCI: Use BAR index in sysfs attr->private instead of resource pointer
  alpha/PCI: Add security_locked_down() check to pci_mmap_resource()
  PCI/sysfs: Limit pci_sysfs_init() late_initcall compile scope
  PCI/sysfs: Add stubs for pci_{create,remove}_sysfs_dev_files()
  PCI/sysfs: Warn about BAR resize failure in __resource_resize_store()
  PCI/sysfs: Convert PCI resource files to static attributes
  PCI/proc: Fix race between pci_proc_init() and pci_bus_add_device()
  ...

Pull kvm updates from Paolo Bonzini:
 "arm64:

     This is a bit of an odd merge window on the KVM/arm64 front. There
     is absolutely no new feature in the pull request. It is purely
     fixes, because it is simply becoming too hard to review new stuff
     when so many AI-fuelled fixes hit the list.

   - Significant cleanup of the vgic-v5 PPI support which was merged in
     7.1. This makes the code more maintainable, and squashes a couple
     of bugs in the meantime

   - Set of fixes for the handling of the MMU in an NV context,
     particularly VNCR-triggered faults. S1POE support is fixed as well

   - Large set of pKVM fixes, mostly addressing recurring issues around
     hypervisor tracking of donated pages in obscure cases where the
     donation could fail and leave things in a bizarre state

   - Fixes for the so-called "lazy vgic init", which resulted in
     sleeping operations in non-preemptible sections. This turned out to
     be far more invasive than initially expected..

   - Reduce the overhead of L1/L2 context switch by not touching the FP
     registers

   - Fix the way non-implemented page sizes are dealt with when a guest
     insist on using them for S2 translation

   - The usual set of low-impact fixes and cleanups all over the map

  Loongarch:

   - On a request for lazy FPU load, load all FPU state that the VM
     supports instead of enabling only the part (FPU, LSX or LASX) that
     caused the FPU load request

   - Some enhancements about interrupt injection

   - Some bug fixes and other small changes

  RISC-V:

   - Batch G-stage TLB flushes for GPA range based page table updates

   - Convert HGEI line management to fully per-HART

   - Fix missing CSR dirty marking when FWFT state updated via ONE_REG

   - Fix stale FWFT feature exposure to Guest/VM

   - Speed up dirty logging write faults using MMU rwlock and atomic PTE
     updates using cmpxchg() for permission-only changes

   - Use flexible array for APLIC IRQ state

   - Use kvm_slot_dirty_track_enabled() for logging enable check on a
     memslot

   - Avoid skipping valid pages in kvm_riscv_gstage_wp_range()

   - Avoid skipping valid pages in kvm_riscv_gstage_unmap_range()

   - Use endian-specific __lelong for NACL shared memory

  S390:

   - KVM_PRE_FAULT_MEMORY support

   - Support for 2G hugepages

   - Support for the ASTFLEIE 2 facility

   - Support for fast inject using kvm_arch_set_irq_inatomic

   - Fix potential leak of uninitialized bytes

   - A few more misc gmap fixes

  x86:

   - Generic support for the more granular permissions allowed by EPT,
     namely "read" (which was previously usurping the U bit) and
     separate execution bits for kernel and userspace

   - Do not assume that all page tables start with U=1/W=1/NX=0 at the
     root, as AMD GMET needs to have U=0 at the root

   - Introduce common assembly macros for use within Intel and AMD
     vendor-specific vmentry code. This touches the SPEC_CTRL handling,
     which is now entirely done in assembly for Intel (by reusing the
     AMD code that already existed), and register save/restore which
     uses some macro magic to compute the offsets in the struct. Both of
     these are preparatory changes for upcoming APX support

   - Clean up KVM's register tracking and storage, primarily to prepare
     for APX support, which expands the maximum number of GPRs from 16
     to 32

   - Keep a single copy of the PDPTRs rather than two, since
     architecturally there is just one

   - Handle EXIT_FASTPATH_EXIT_USERSPACE in vendor code to ensure vendor
     code gets a chance to handle things like reaping the PML buffer

   - Update KVM's view of PV async enabling if and only if the MSR write
     fully succeeds

   - Fix a variety of issues where the emulator doesn't honor
     guest-debug state, and clean up related code along the way

   - Synthesize EPT Violation and #NPF "error code" bits when injecting
     faults into L1 that didn't originate in hardware (in which case the
     VMCS/VMCB doesn't hold relevant information)

   - Add support for virtualizing (well, emulating) AMD's flavor of
     CPL>0 CPUID faulting

   - Clean up the GPR APIs so that KVM's use of "raw" is consistent, and
     fix a variety of minor bugs along the way

   - Fix an OOB memory access due to not checking the VP ID when
     handling a Hyper-V PV TLB flush for L2

   - Fix a bug in the mediated PMU's handling of fixed counters that
     allowed the guest to bypass the PMU event filter

   - Allow userspace to return EAGAIN when handling SNP and TDX
     hypercalls, so the KVM can forward a "retry" status code to the
     guest, and reserve all unused error codes for future usage

   - Overhaul the TDP MMU => S-EPT code to move as much S-EPT specific
     logic as possible into the TDX code, and to funnel (almost) all
     S-EPT updates into a single chokepoint. The motivation is largely
     to prepare for upcoming Dynamic PAMT support, but the cleanups are
     nice to have on their own

   - Plug a hole in shadow page table handling, where KVM fails to
     recursively zap nested EPT/NPT shadow page tables when the nested
     hypervisor tears down its own EPT/NPT page tables from the bottom
     up

  x86 (Intel):

   - Support for nested MBEC (Mode-Based Execute Control), see above in
     the generic section; also run with MBEC enabled even for non-nested
     mode

   - Use the kernel's "enum pg_level" in the TDX APIs instead of the
     TDX-Module's level definitions (which are 0-based)

   - Rework the TDX memory APIs to not require/assume that guest memory
     is backed by "struct page" (in prepartion for guest_memfd hugepage
     support)

   - Fix a largely benign bug where KVM TDX would incorrectly state it
     could emulate several x2APIC MSRs

   - Use the "safe" WRMSR API when proxying LBR MSR writes as the
     to-be-written value is guest controlled and completely unvalidated

  x86 (AMD):

   - Support for nested GMET (Guest Mode Execution Trap), see above in
     the generic section; also run with GMET enabled even for non-nested
     mode

   - Fixes and minor cleanups to GHCB handling, on top of the earlier
     work already merged into 7.1-rc

   - Ensure KVM's copy of CR0 and CR3 are up-to-date prior to invoking
     fastpath handlers

   - Add support for virtualizing gPAT (KVM previously just used L1's
     PAT when running L2)

   - Fix goofs where KVM mishandles side effects (e.g. single-step and
     PMC updates) when emulating VMRUN

   - Fix a variety of bugs in AVIC's handling of x2APIC MSR
     interception, most notably where KVM didn't disable interception of
     IRR, ISR, and TMR regs

   - Add support for virtualizing Host-Only/Guest-Only bits in the
     mediated PMU

   - Don't advertise support for unusable VM types, and account for VM
     types that are disabled by firmware, e.g. to mitigate security
     vulnerabilities

   - Rewrite the SEV {en,de}crypt debug ioctls as they were riddle with
     bugs and unnecessarily complicated, and add comprehensive tests

   - Clean up and deduplicate the SEV page pinning code

   - Fix minor goofs related to writing back CPUID information after
     firmware rejects a CPUID page for an SNP vCPU

  Generic:

   - Rename invalidate_begin() to invalidate_start() throughout KVM to
     follow the kernel's nomenclature, e.g. for mmu_notifiers

   - Use guard() to cleanup up various KVM+VFIO flows

   - Minor cleanups

  guest_memfd:

   - Return -EEXIST instead of -EINVAL if userspace attempts to bind a
     gmem range to multiple memslots, and fix the test that was supposed
     to ensure KVM returns -EEXIST

   - Treat memslot binding offsets and sizes as unsigned values to fix a
     bug where KVM interprets a large "offset + size" as a negative
     value and allows a nonsensical offset

   - Use the inode number instead of the page offset for the NUMA
     interleaving index to fix a bug where the effective index would
     jump by two for consecutive pages (the caller also adds in the page
     offset)

  Selftests:

   - Randomize the dirty log test's delay when reaping the bitmap on the
     first pass, as always waiting only 1ms hid a KVM RISC-V bug as the
     test reaped the bitmap before KVM could build up enough state to
     hit the bug

   - A pile of one-off fixes and cleanups"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (326 commits)
  KVM: x86/mmu: Ensure hugepage is in by slot before checking max mapping level
  KVM: x86: Fix shadow paging use-after-free due to unexpected role
  KVM: s390: Introducing kvm_arch_set_irq_inatomic fast inject
  KVM: s390: Enable adapter_indicators_set to use mapped pages
  KVM: s390: Add map/unmap ioctl and clean mappings post-guest
  riscv: kvm: Use endian-specific __lelong for NACL shared memory
  KVM: selftests: access_tracking_perf_test: bump number of NUMA nodes to 32
  KVM: s390: vsie: Implement ASTFLEIE facility 2
  KVM: s390: vsie: Refactor handle_stfle
  s390/sclp: Detect ASTFLEIE 2 facility
  KVM: s390: Minor refactor of base/ext facility lists
  KVM: x86/mmu: move pdptrs out of the MMU
  KVM: x86: check that kvm_handle_invpcid is only invoked with shadow paging
  KVM: nSVM: invalidate cached PDPTRs across nested NPT transitions
  KVM: nVMX: remove unnecessary code in prepare_vmcs02_rare
  KVM: x86: remove nested_mmu from mmu_is_nested()
  KVM: arm64: vgic-its: Make ABI commit helpers return void
  KVM: s390: Initialize KVM_S390_GET_CMMA_BITS memory
  LoongArch: KVM: Add missing slots_lock for device register/unregister
  LoongArch: KVM: Validate irqchip index in irqfd routing
  ...

Pull crypto updates from Herbert Xu:
 "API:
   - Drop support for off-CPU cryptography in af_alg
   - Document that af_alg is *always* slower
   - Document the deprecation of af_alg
   - Remove zero-copy support from skcipher and aead in af_alg
   - Cap AEAD AD length to 0x80000000 in af_alg
   - Free default RNG on module exit

  Algorithms:
   - Fix vli multiplication carry overflow in ecc
   - Drop unused cipher_null crypto_alg
   - Remove unused variants of drbg
   - Use lib/crypto in drbg
   - Use memcpy_from/to_sglist in authencesn
   - Allow authenc(hmac(sha{256,384}),cts(cbc(aes))) in FIPS mode
   - Disallow RSA PKCS#1 SHA-1 sig algs in FIPS mode
   - Filter out async aead implementations at alloc in krb5
   - Fix non-parallel fallback by rstoring callback in pcrypt
   - Validate poly1305 template argument in chacha20poly1305

  Drivers:
   - Add sysfs PCI reset support to qat
   - Add KPT support for GEN6 devices to qat
   - Remove unused character device and ioctls from qat
   - Add support for hw access via SMCC to mtk
   - Remove prng support from crypto4xx
   - Remove prng support from hisi-trng
   - Remove prng support from sun4i-ss
   - Remove prng support from xilinx-trng
   - Remove loongson-rng
   - Remove exynos-rng

  Others:
   - Remove support for AIO on sockets"

* tag 'v7.2-p1' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (196 commits)
  crypto: tegra - fix refcount leak in tegra_se_host1x_submit()
  crypto: rng - Free default RNG on module exit
  crypto: testmgr - allow authenc(hmac(sha{256,384}),cts(cbc(aes))) in FIPS mode
  hwrng: jh7110 - fix refcount leak in starfive_trng_read()
  crypto: atmel-ecc - drop dead code in atmel_ecdh_max_size
  crypto: cavium/cpt - fix DMA cleanup using wrong loop index
  crypto: marvell/octeontx - fix DMA cleanup using wrong loop index
  MAINTAINERS: make myself the maintainer of the Qualcomm QCE driver
  crypto: amcc - convert irq_of_parse_and_map to platform_get_irq
  crypto: sun4i-ss - Remove insecure and unused rng_alg
  hwrng: xilinx - Move xilinx-rng into drivers/char/hw_random/
  crypto: xilinx-trng - Replace crypto_drbg_ctr_df() with HMAC-SHA512
  crypto: xilinx-trng - Fix return value of xtrng_hwrng_trng_read()
  crypto: xilinx-trng - Remove crypto_rng interface
  crypto: exynos-rng - Remove exynos-rng driver
  hwrng: hisi-trng - Move hisi-trng into drivers/char/hw_random/
  crypto: hisi-trng - Remove crypto_rng interface
  crypto: loongson - Remove broken and unused loongson-rng
  crypto: crypto4xx - Remove insecure and unused rng_alg
  crypto: qat - validate RSA CRT component lengths
  ...

The timeout error path in tegra_se_host1x_submit() returns without
calling host1x_job_put(), while all other paths (success, submit
error, pin error) properly release the job reference through the
job_put label.  Since host1x_job_alloc() initializes the reference
count and host1x_job_put() is required to drop it, omitting it on
timeout causes a permanent refcount leak.

Fix this by redirecting the timeout return to the existing job_put
label, ensuring the job reference and any associated syncpt
references are consistently released.

Cc: stable@vger.kernel.org
Fixes: 0880bb3b00c8 ("crypto: tegra - Add Tegra Security Engine driver")
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Reviewed-by: Akhil R <akhilrajeev@nvidia.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

atmel_ecdh_init_tfm() always allocates ctx->fallback, so it is never
NULL in atmel_ecdh_max_size(). Remove the dead code and return
crypto_kpp_maxsize() directly.

Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The sg_cleanup error path used list[i] instead of list[j] when unmapping
DMA buffers, leaking successfully mapped entries and repeatedly unmapping
the failed one.

Fixes: c694b233295b ("crypto: cavium - Add the Virtual Function driver for CPT")
Signed-off-by: Felix Gu <ustc.gu@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The sg_cleanup path used list[i] instead of list[j] when unmapping DMA
buffers, leaking successfully mapped entries and repeatedly unmapping
the failed one.

Fixes: 10b4f09491bf ("crypto: marvell - add the Virtual Function driver for CPT")
Signed-off-by: Felix Gu <ustc.gu@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Replace the deprecated irq_of_parse_and_map() call with the modern
platform_get_irq() in the probe function. This also improves error
handling: platform_get_irq() returns a negative errno on failure,
whereas irq_of_parse_and_map() returned 0.

Change the irq field in struct crypto4xx_core_device from u32 to int
to match the return type of platform_get_irq().

Assisted-by: opencode:big-pickle
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Remove sun4i_ss_rng, as it is insecure and unused:

- It has multiple vulnerabilities.  sun4i_ss_prng_seed() is missing
  locking and has a buffer overflow.  sun4i_ss_prng_generate() fails to
  fill the entire buffer with cryptographic random bytes, because it
  rounds the destination length down and also doesn't actually wait for
  the hardware to be ready before pulling bytes from it.

- No user of this code is known.  It's usable only theoretically via the
  "rng" algorithm type of AF_ALG.  But userspace actually just uses the
  actual Linux RNG (/dev/random etc) instead.  And rng_algs don't
  contribute entropy to the actual Linux RNG either.  (This may have
  been confused with hwrng, which does contribute entropy.)

The sun4i_ss_prng_seed() buffer overflow was reported by Tianchu Chen
and discovered by Atuin - Automated Vulnerability Discovery Engine

There's no point in fixing all these vulnerabilities individually when
this is unused code, so let's just remove it.

Fixes: b8ae5c7387ad ("crypto: sun4i-ss - support the Security System PRNG")
Cc: stable@vger.kernel.org
Reported-by: Tianchu Chen <flynnnchen@tencent.com>
Closes: https://lore.kernel.org/r/af749a8447bd7f0e9dd26ca6c87e9c6afecb09d9@linux.dev/
Acked-by: Corentin LABBE <clabbe.montjoie@gmail.com>
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Since this file just implements a hwrng driver, move it into
drivers/char/hw_random/.  Rename the kconfig option accordingly as well.

Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>