Pull clk fixes from Stephen Boyd:
 "Two reverts and two EN7581 driver fixes:

   - Revert the attempt to make CLK_GET_RATE_NOCACHE flag work in
     clk_set_rate() because it led to problems with the Qualcomm CPUFreq
     driver

   - Revert Amlogic reset driver back to the initial implementation.
     This broke probe of the audio subsystem on axg based platforms and
     also had compilation problems. We'll try again next time.

   - Fix a clk frequency and fix array bounds runtime checks in the
     Airoha EN7581 driver"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: en7523: Initialize num before accessing hws in en7523_register_clocks()
  clk: en7523: Fix wrong BUS clock for EN7581
  clk: amlogic: axg-audio: revert reset implementation
  Revert "clk: Fix invalid execution of clk_set_rate"

With the new __counted_by annotation in clk_hw_onecell_data, the "num"
struct member must be set before accessing the "hws" array. Failing to
do so will trigger a runtime warning when enabling CONFIG_UBSAN_BOUNDS
and CONFIG_FORTIFY_SOURCE.

Fixes: f316cdff8d67 ("clk: Annotate struct clk_hw_onecell_data with __counted_by")
Signed-off-by: Haoyu Li <lihaoyu499@gmail.com>
Link: https://lore.kernel.org/r/20241203142915.345523-1-lihaoyu499@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

The Documentation for EN7581 had a typo and still referenced the EN7523
BUS base source frequency. This was in conflict with a different page in
the Documentration that state that the BUS runs at 300MHz (600MHz source
with divisor set to 2) and the actual watchdog that tick at half the BUS
clock (150MHz). This was verified with the watchdog by timing the
seconds that the system takes to reboot (due too watchdog) and by
operating on different values of the BUS divisor.

The correct values for source of BUS clock are 600MHz and 540MHz.

This was also confirmed by Airoha.

Cc: stable@vger.kernel.org
Fixes: 66bc47326ce2 ("clk: en7523: Add EN7581 support")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20241116105710.19748-1-ansuelsmth@gmail.com
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

The audio subsystem of axg based platform is not probing anymore.
This is due to the introduction of RESET_MESON_AUX and the config
not being enabled with the default arm64 defconfig.

This brought another discussion around proper decoupling between
the clock and reset part. While this discussion gets sorted out,
revert back to the initial implementation.

This reverts
 * commit 681ed497d676 ("clk: amlogic: axg-audio: fix Kconfig dependency on RESET_MESON_AUX")
 * commit 664988eb47dd ("clk: amlogic: axg-audio: use the auxiliary reset driver")

Both are reverted with single change to avoid creating more compilation
problems.

Fixes: 681ed497d676 ("clk: amlogic: axg-audio: fix Kconfig dependency on RESET_MESON_AUX")
Cc: Arnd Bergmann <arnd@arndb.de>
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20241128-clk-audio-fix-rst-missing-v2-1-cf437d1a73da@baylibre.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

This reverts commit 25f1c96a0e841013647d788d4598e364e5c2ebb7.

The offending commit results in errors like

	cpu cpu0: _opp_config_clk_single: failed to set clock rate: -22

spamming the logs on the Lenovo ThinkPad X13s and other Qualcomm
machines when cpufreq tries to update the CPUFreq HW Engine clocks.

As mentioned in commit 4370232c727b ("cpufreq: qcom-hw: Add CPU clock
provider support"):

	[T]he frequency supplied by the driver is the actual frequency
	that comes out of the EPSS/OSM block after the DCVS operation.
	This frequency is not same as what the CPUFreq framework has set
	but it is the one that gets supplied to the CPUs after
	throttling by LMh.

which seems to suggest that the driver relies on the previous behaviour
of clk_set_rate().

Since this affects many Qualcomm machines, let's revert for now.

Fixes: 25f1c96a0e84 ("clk: Fix invalid execution of clk_set_rate")
Reported-by: Aishwarya TCV <aishwarya.tcv@arm.com>
Link: https://lore.kernel.org/all/e2d83e57-ad07-411b-99f6-a4fc3c4534fa@arm.com/
Cc: Chuan Liu <chuan.liu@amlogic.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241202100621.29209-1-johan+linaro@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

Clean up the existing export namespace code along the same lines of
commit 33def8498fdd ("treewide: Convert macro and uses of __section(foo)
to __section("foo")") and for the same reason, it is not desired for the
namespace argument to be a macro expansion itself.

Scripted using

  git grep -l -e MODULE_IMPORT_NS -e EXPORT_SYMBOL_NS | while read file;
  do
    awk -i inplace '
      /^#define EXPORT_SYMBOL_NS/ {
        gsub(/__stringify\(ns\)/, "ns");
        print;
        next;
      }
      /^#define MODULE_IMPORT_NS/ {
        gsub(/__stringify\(ns\)/, "ns");
        print;
        next;
      }
      /MODULE_IMPORT_NS/ {
        $0 = gensub(/MODULE_IMPORT_NS\(([^)]*)\)/, "MODULE_IMPORT_NS(\"\\1\")", "g");
      }
      /EXPORT_SYMBOL_NS/ {
        if ($0 ~ /(EXPORT_SYMBOL_NS[^(]*)\(([^,]+),/) {
  	if ($0 !~ /(EXPORT_SYMBOL_NS[^(]*)\(([^,]+), ([^)]+)\)/ &&
  	    $0 !~ /(EXPORT_SYMBOL_NS[^(]*)\(\)/ &&
  	    $0 !~ /^my/) {
  	  getline line;
  	  gsub(/[[:space:]]*\\$/, "");
  	  gsub(/[[:space:]]/, "", line);
  	  $0 = $0 " " line;
  	}

  	$0 = gensub(/(EXPORT_SYMBOL_NS[^(]*)\(([^,]+), ([^)]+)\)/,
  		    "\\1(\\2, \"\\3\")", "g");
        }
      }
      { print }' $file;
  done

Requested-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://mail.google.com/mail/u/2/#inbox/FMfcgzQXKWgMmjdFwwdsfgxzKpVHWPlc
Acked-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull clk updates from Stephen Boyd:
 "The core framework gained a clk provider helper, a clk consumer
  helper, and some unit tests for the assigned clk rates feature in
  DeviceTree. On the vendor driver side, we gained a whole pile of SoC
  driver support detailed below. The majority in the diffstat is
  Qualcomm, but there's also quite a few Samsung and Mediatek clk driver
  additions in here as well. The top vendors is quite common, but the
  sheer amount of new drivers is uncommon, so I'm anticipating a larger
  number of fixes for clk drivers this cycle.

  Core:
   - devm_clk_bulk_get_all_enabled() to return number of clks acquired
   - devm_clk_hw_register_gate_parent_hw() helper to modernize drivers
   - KUnit tests for clk-assigned-rates{,-u64}

  New Drivers:
   - Marvell PXA1908 SoC clks
   - Mobileye EyeQ5, EyeQ6L and EyeQ6H clk driver
   - TWL6030 clk driver
   - Nuvoton Arbel BMC NPCM8XX SoC clks
   - MediaTek MT6735 SoC clks
   - MediaTek MT7620, MT7628 and MT7688 MMC clks
   - Add a driver for gated fixed rate clocks
   - Global clock controllers for Qualcomm QCS8300 and IPQ5424 SoCs
   - Camera, display and video clock controllers for Qualcomm SA8775P
     SoCs
   - Global, display, GPU, TCSR, and RPMh clock controllers for Qualcomm
     SAR2130P
   - Global, camera, display, GPU, and video clock controllers for
     Qualcomm SM8475 SoCs
   - RTC power domain and Battery Backup Function (VBATTB) clock support
     for the Renesas RZ/G3S SoC
   - Qualcomm IPQ9574 alpha PLLs
   - Support for i.MX91 CCM in the i.MX93 driver
   - Microchip LAN969X SoC clks
   - Cortex-A55 core clocks and Interrupt Control Unit (ICU) clock and
     reset on Renesas RZ/V2H(P)
   - Samsung ExynosAutov920 clk drivers for PERIC1, MISC, HSI0 and HSI1
   - Samsung Exynos8895 clk drivers for FSYS0/1, PERIC0/1, PERIS and TOP

  Updates:
   - Convert more clk bindings to YAML
   - Various clk driver cleanups: NULL checks, add const, etc.
   - Remove END/NUM #defines that count number of clks in various
     binding headers
   - Continue moving reset drivers to drivers/reset via auxiliary bus"

* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (162 commits)
  clk: clk-loongson2: Fix potential buffer overflow in flexible-array member access
  clk: Fix invalid execution of clk_set_rate
  clk: clk-loongson2: Fix memory corruption bug in struct loongson2_clk_provider
  clk: lan966x: make it selectable for ARCH_LAN969X
  clk: eyeq: add EyeQ6H west fixed factor clocks
  clk: eyeq: add EyeQ6H central fixed factor clocks
  clk: eyeq: add EyeQ5 fixed factor clocks
  clk: eyeq: add fixed factor clocks infrastructure
  clk: eyeq: require clock index with phandle in all cases
  clk: fixed-factor: add clk_hw_register_fixed_factor_index() function
  dt-bindings: clock: eyeq: add more Mobileye EyeQ5/EyeQ6H clocks
  dt-bindings: soc: mobileye: set `#clock-cells = <1>` for all compatibles
  clk: clk-axi-clkgen: make sure to enable the AXI bus clock
  dt-bindings: clock: axi-clkgen: include AXI clk
  clk: mmp: Add Marvell PXA1908 MPMU driver
  clk: mmp: Add Marvell PXA1908 APMU driver
  clk: mmp: Add Marvell PXA1908 APBCP driver
  clk: mmp: Add Marvell PXA1908 APBC driver
  dt-bindings: clock: Add Marvell PXA1908 clock bindings
  clk: mmp: Switch to use struct u32_fract instead of custom one
  ...

 - Add devm_clk_bulk_get_all_enabled() to return number of clks acquired
 - Marvell PXA1908 SoC clks

* clk-marvell:
  clk: mmp: Add Marvell PXA1908 MPMU driver
  clk: mmp: Add Marvell PXA1908 APMU driver
  clk: mmp: Add Marvell PXA1908 APBCP driver
  clk: mmp: Add Marvell PXA1908 APBC driver
  dt-bindings: clock: Add Marvell PXA1908 clock bindings
  clk: mmp: Switch to use struct u32_fract instead of custom one

* clk-adi:
  clk: clk-axi-clkgen: make sure to enable the AXI bus clock
  dt-bindings: clock: axi-clkgen: include AXI clk

* clk-qcom: (43 commits)
  clk: qcom: remove unused data from gcc-ipq5424.c
  clk: qcom: Add support for Global Clock Controller on QCS8300
  dt-bindings: clock: qcom: Add GCC clocks for QCS8300
  clk: qcom: add Global Clock controller (GCC) driver for IPQ5424 SoC
  clk: qcom: clk-alpha-pll: Add NSS HUAYRA ALPHA PLL support for ipq9574
  dt-bindings: clock: Add Qualcomm IPQ5424 GCC binding
  clk: qcom: add SAR2130P GPU Clock Controller support
  clk: qcom: dispcc-sm8550: enable support for SAR2130P
  clk: qcom: tcsrcc-sm8550: add SAR2130P support
  clk: qcom: add support for GCC on SAR2130P
  clk: qcom: rpmh: add support for SAR2130P
  clk: qcom: rcg2: add clk_rcg2_shared_floor_ops
  dt-bindings: clk: qcom,sm8450-gpucc: add SAR2130P compatibles
  dt-bindings: clock: qcom,sm8550-dispcc: Add SAR2130P compatible
  dt-bindings: clock: qcom,sm8550-tcsr: Add SAR2130P compatible
  dt-bindings: clock: qcom: document SAR2130P Global Clock Controller
  dt-bindings: clock: qcom,rpmhcc: Add SAR2130P compatible
  clk: qcom: Make GCC_6125 depend on QCOM_GDSC
  dt-bindings: clock: qcom: gcc-ipq9574: remove q6 bring up clock macros
  dt-bindings: clock: qcom: gcc-ipq5332: remove q6 bring up clock macros
  ...

* clk-devm:
  clk: Provide devm_clk_bulk_get_all_enabled() helper

* clk-samsung:
  clk: samsung: Introduce Exynos8895 clock driver
  clk: samsung: clk-pll: Add support for pll_{1051x,1052x}
  dt-bindings: clock: samsung: Add Exynos8895 SoC
  clk: samsung: gs101: make all ufs related clocks critical
  clk: samsung: exynosautov920: add peric1, misc and hsi0/1 clock support
  dt-bindings: clock: exynosautov920: add peric1, misc and hsi0/1 clock definitions
  clk: samsung: Fix out-of-bound access of of_match_node()
  dt-bindings: clock: samsung: remove define with number of clocks for FSD
  clk: samsung: fsd: do not define number of clocks in bindings
  clk: samsung: Fix errors reported by checkpatch
  clk: samsung: Fix block comment style warnings reported by checkpatch

* clk-microchip:
  clk: lan966x: add support for lan969x SoC clock driver
  clk: lan966x: prepare driver for lan969x support
  clk: lan966x: make clk_names const char * const
  dt-bindings: clock: add support for lan969x

* clk-imx:
  clk: imx: imx8-acm: Fix return value check in clk_imx_acm_attach_pm_domains()
  clk: imx: lpcg-scu: Skip HDMI LPCG clock save/restore
  clk: imx: clk-scu: fix clk enable state save and restore
  clk: imx: fracn-gppll: fix pll power up
  clk: imx: fracn-gppll: correct PLL initialization flow
  clk: imx: lpcg-scu: SW workaround for errata (e10858)
  clk: imx: add i.MX91 clk
  dt-bindings: clock: Add i.MX91 clock support
  dt-bindings: clock: imx93: Drop IMX93_CLK_END macro definition
  clk: imx93: Move IMX93_CLK_END macro to clk driver
  clk: imx95-blk-ctl: Add one clock gate for HSIO block
  dt-bindings: clock: nxp,imx95-blk-ctl: Add compatible string for i.MX95 HSIO BLK CTRL

* clk-amlogic:
  clk: amlogic: axg-audio: fix Kconfig dependency on RESET_MESON_AUX
  clk: amlogic: axg-audio: use the auxiliary reset driver
  reset: amlogic: Fix small whitespace issue
  reset: amlogic: add auxiliary reset driver support
  reset: amlogic: split the device core and platform probe
  reset: amlogic: move drivers to a dedicated directory
  reset: amlogic: add reset status support
  reset: amlogic: use reset number instead of register count
  reset: amlogic: add driver parameters
  reset: amlogic: make parameters unsigned
  reset: amlogic: use generic data matching function
  reset: amlogic: convert driver to regmap
  dt-bindings: clock: convert amlogic,meson8b-clkc.txt to dtschema
  clk: meson: meson8b: remove spinlock
  clk: meson: mpll: Delete a useless spinlock from the MPLL
  clk: meson: s4: pll: fix frac maximum value for hifi_pll
  clk: meson: c3: pll: fix frac maximum value for hifi_pll
  clk: meson: Support PLL with fixed fractional denominators
  clk: meson: s4: pll: hifi_pll support fractional multiplier

* clk-allwinner:
  clk: sunxi-ng: Use of_property_present() for non-boolean properties
  clk: sunxi-ng: d1: Fix PLL_AUDIO0 preset
  clk: sunxi-ng: Constify struct ccu_reset_map
  clk: sunxi-ng: h616: Add sigma-delta modulation settings for audio PLL

 - Mobileye EyeQ5, EyeQ6L and EyeQ6H clk driver
 - TWL6030 clk driver
 - Nuvoton Arbel BMC NPCM8XX SoC clks
 - Convert more clk bindings to YAML

* clk-mobileye:
  clk: eyeq: add EyeQ6H west fixed factor clocks
  clk: eyeq: add EyeQ6H central fixed factor clocks
  clk: eyeq: add EyeQ5 fixed factor clocks
  clk: eyeq: add fixed factor clocks infrastructure
  clk: eyeq: require clock index with phandle in all cases
  clk: fixed-factor: add clk_hw_register_fixed_factor_index() function
  dt-bindings: clock: eyeq: add more Mobileye EyeQ5/EyeQ6H clocks
  dt-bindings: soc: mobileye: set `#clock-cells = <1>` for all compatibles
  clk: eyeq: add driver
  clk: divider: Introduce CLK_DIVIDER_EVEN_INTEGERS flag
  dt-bindings: clock: add Mobileye EyeQ6L/EyeQ6H clock indexes
  Revert "dt-bindings: clock: mobileye,eyeq5-clk: add bindings"

* clk-twl:
  clk: twl: add TWL6030 support
  clk: twl: remove is_prepared

* clk-nuvoton:
  clk: npcm8xx: add clock controller
  reset: npcm: register npcm8xx clock auxiliary bus device
  dt-bindings: reset: npcm: add clock properties

* clk-renesas:
  clk: renesas: vbattb: Add VBATTB clock driver
  clk: Add devm_clk_hw_register_gate_parent_hw()
  clk: renesas: rzg2l: Fix FOUTPOSTDIV clk
  dt-bindings: clock: renesas,r9a08g045-vbattb: Document VBATTB
  clk: renesas: r9a08g045: Add power domain for RTC
  clk: renesas: r9a08g045: Mark the watchdog and always-on PM domains as IRQ safe
  clk: renesas: rzg2l-cpg: Use GENPD_FLAG_* flags instead of local ones
  clk: renesas: rzg2l-cpg: Move PM domain power on in rzg2l_cpg_pd_setup()
  dt-bindings: clock: r9a08g045-cpg: Add power domain ID for RTC
  clk: renesas: r8a779h0: Drop CLK_PLL2_DIV2 to clarify ZCn clocks
  clk: renesas: r9a09g057: Add clock and reset entries for ICU
  clk: renesas: r9a09g057: Add CA55 core clocks
  clk: renesas: Remove duplicate and trailing empty lines

* clk-bindings:
  dt-bindings: clock: actions,owl-cmu: convert to YAML
  dt-bindings: clock: ti: Convert mux.txt to json-schema
  dt-bindings: clock: ti: Convert divider.txt to json-schema
  dt-bindings: clock: ti: Convert interface.txt to json-schema
  dt-bindings: clock: convert rockchip,rk3328-cru.txt to YAML