tegra-bpmp clocks driver makes implicit conversion of signed error
code to unsigned value in recalc_rate operation. The behavior for
recalc_rate, according to it's specification, should be that "If the
driver cannot figure out a rate for this clock, it must return 0."
Fixes: ca6f2796eef7 ("clk: tegra: Add BPMP clock driver")
Signed-off-by: Timo Alho <talho@nvidia.com>
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Link: https://lore.kernel.org/r/20230912112951.2330497-1-cyndis@kapsi.fi
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Rework the write operation such that the Byte Count register is written with
a single raw i2c write outside of regmap using transfer which does specify
the number of bytes to be transfered, one in this case, and which makes the
expected subsequent write transfer look like address+register+data, and then
make use of this method. Without this change, the Byte Count register write
in probe() would succeed as it would provide the byte count as part of its
write payload, but any subsequent writes would fail due to this Byte Count
register programming. Such failing writes happens e.g. during resume, when
restoring the regmap content.
Fixes: edc12763a3a2 ("clk: si521xx: Clock driver for Skyworks Si521xx I2C PCIe clock generators")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20230831181656.154750-2-marex@denx.de
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In order to reload registers into the clock generator on resume using
regcache_sync(), it is necessary to select one of the regcache types
which are not NONE. Since this device has some 7 registers, use the
simplest one, FLAT. The regcache code complains about REGCACHE_NONE
being selected and generates a WARNING, this fixes that warning.
Fixes: edc12763a3a2 ("clk: si521xx: Clock driver for Skyworks Si521xx I2C PCIe clock generators")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20230831181656.154750-1-marex@denx.de
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The thm*_clk have two clock sources 32k and 250k,excluding 32m.
Fixes: af3bd36573e3 ("clk: sprd: Add clocks support for UMS512")
Signed-off-by: Zhifeng Tang <zhifeng.tang@unisoc.com>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230824092624.20020-1-zhifeng.tang@unisoc.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Make vc3_clk_mux enum values depend upon vc3_clk enum values to avoid any accidental breakage in the future. Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/r/20230824104812.147775-5-biju.das.jz@bp.renesas.com Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
According to Table 3. ("Output Source") in the 5P35023 datasheet,
the output clock mapping should be 0=REF, 1=SE1, 2=SE2, 3=SE3,
4=DIFF1, 5=DIFF2. But the code uses inverse. Fix this mapping issue.
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Closes: https://lore.kernel.org/all/CAMuHMdUHD+bEco=WYTYWsTAyRt3dTQQt4Xpaejss0Y2ZpLCMNg@mail.gmail.com/
Fixes: 6e9aff555db7 ("clk: Add support for versa3 clock driver")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230824104812.147775-4-biju.das.jz@bp.renesas.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fix the below cocci warnings by replacing do_div()->div64_ul() and
bound the result with a max value of U16_MAX.
cocci warnings:
drivers/clk/clk-versaclock3.c:404:2-8: WARNING: do_div() does a
64-by-32 division, please consider using div64_ul instead.
Reported-by: Julia Lawall <julia.lawall@inria.fr>
Closes: https://lore.kernel.org/r/202307270841.yr5HxYIl-lkp@intel.com/
Fixes: 6e9aff555db7 ("clk: Add support for versa3 clock driver")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230824104812.147775-3-biju.das.jz@bp.renesas.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Pull clk subsystem updates from Stephen Boyd:
"This pull request is full of clk driver changes. In fact, there aren't
any changes to the clk framework this time around. That's probably
because everyone was on vacation (yours truly included). We did lose a
couple clk drivers this time around because nobody was using those
devices. That skews the diffstat a bit, but either way, nothing looks
out of the ordinary here. The usual suspects are chugging along adding
support for more SoCs and fixing bugs.
If I had to choose, I'd say the theme for the past few months has been
"polish". There's quite a few patches that migrate to
devm_platform_ioremap_resource() in here. And there's more than a
handful of patches that move the NR_CLKS define from the DT binding
header to the driver. There's even patches that migrate drivers to use
clk_parent_data and clk_hw to describe clk tree topology. It seems
that the spring (summer?) cleaning bug got some folks, or the
semiconductor shortage finally hit the software side.
New Drivers:
- StarFive JH7110 SoC clock drivers
- Qualcomm IPQ5018 Global Clock Controller driver
- Versa3 clk generator to support 48KHz playback/record with audio
codec on RZ/G2L SMARC EVK
Removed Drivers:
- Remove non-OF mmp clk drivers
- Remove OXNAS clk driver
Updates:
- Add __counted_by to struct clk_hw_onecell_data and struct
spmi_pmic_div_clk_cc
- Move defines for numbers of clks (NR_CLKS) from DT headers to
drivers
- Introduce kstrdup_and_replace() and use it
- Add PLL rates for Rockchip rk3568
- Add the display clock tree for Rockchip rv1126
- Add Audio Clock Generator (ADG) clocks on Renesas R-Car Gen3 and
RZ/G2 SoCs
- Convert sun9i-mmc clock to use
devm_platform_get_and_ioremap_resource()
- Fix function name in a comment in ccu_mmc_timing.c
- Parameter name correction for ccu_nkm_round_rate()
- Implement CLK_SET_RATE_PARENT for Allwinner NKM clocks, i.e.
consider alternative parent rates when determining clock rates
- Set CLK_SET_RATE_PARENT for Allwinner A64 pll-mipi
- Support finding closest (as opposed to closest but not higher)
clock rate for NM, NKM, mux and div type clocks, as use it for
Allwinner A64 pll-video0
- Prefer current parent rate if able to generate ideal clock rate for
Allwinner NKM clocks
- Clean up Qualcomm SMD RPM driver, with interconnect bus clocks
moved out to the interconnect drivers
- Fix various PM runtime bugs across many Qualcomm clk drivers
- Migrate Qualcomm MDM9615 is to parent_hw and parent_data
- Add network related resets on Qualcomm IPQ4019
- Add a couple missing USB related clocks to Qualcomm IPQ9574
- Add missing gpll0_sleep_clk_src to Qualcomm MSM8917 global clock
controller
- In the Qualcomm QDU1000 global clock controller, GDSCs, clkrefs,
and GPLL1 are added, while PCIe pipe clock, SDCC rcg ops are
corrected
- Add missing GDSCs to and correct GDSCs for the SC8280XP global
clock controller driver
- Support retention for the Qualcomm SC8280XP display clock
controller GDSCs.
- Qualcommm's SDCC apps_clk_src is marked with CLK_OPS_PARENT_ENABLE
to fix issues with missing parent clocks across sc7180, sm7150,
sm6350 and sm8250, while sm8450 is corrected to use floor ops
- Correct Qualcomm SM6350 GPU clock controller's clock supplies
- Drop unwanted clocks from the Qualcomm IPQ5332 GCC driver
- Add missing OXILICX GDSC to Qualcomm MSM8226 GCC
- Change the delay in the Qualcomm reset controller to fsleep() for
correctness
- Extend the Qualcomm SM83550 Video clock controller to support
SC8280XP
- Add graphics clock support on Renesas RZ/G2M, RZ/G2N, RZ/G2E, and
R-Car H3, M3-W, and M3-N SoCs
- Add Clocked Serial Interface (CSI) clocks on Renesas RZ/V2M
- Add PWM (MTU3) clock and reset on Renesas RZ/G2UL and RZ/Five
- Add the PDM IPC clock for i.MX93
- Add 519.75MHz frequency support for i.MX9 PLL
- Simplify the .determine_rate() implementation for i.MX GPR mux
- Make the i.MX8QXP LPCG clock use devm_platform_ioremap_resource()
- Add the audio mux clock to i.MX8
- Fix the SPLL2 MULT range for PLLv4
- Update the SPLL2 type in i.MX8ULP
- Fix the SAI4 clock on i.MX8MP
- Add silicon revision print for i.MX25 on clocks init
- Drop the return value from __mx25_clocks_init()
- Fix the clock pauses on no-op set_rate for i.MX8M composite clock
- Drop restrictions for i.MX PLL14xx and fix its max prediv value
- Drop the 393216000 and 361267200 from i.MX PLL14xx rate table to
allow glitch free switching"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (207 commits)
clk: qcom: Fix SM_GPUCC_8450 dependencies
clk: lmk04832: Support using PLL1_LD as SPI readback pin
clk: lmk04832: Don't disable vco clock on probe fail
clk: lmk04832: Set missing parent_names for output clocks
clk: mvebu: Convert to devm_platform_ioremap_resource()
clk: nuvoton: Convert to devm_platform_ioremap_resource()
clk: socfpga: agilex: Convert to devm_platform_ioremap_resource()
clk: ti: Use devm_platform_get_and_ioremap_resource()
clk: mediatek: Convert to devm_platform_ioremap_resource()
clk: hsdk-pll: Convert to devm_platform_ioremap_resource()
clk: gemini: Convert to devm_platform_ioremap_resource()
clk: fsl-sai: Convert to devm_platform_ioremap_resource()
clk: bm1880: Convert to devm_platform_ioremap_resource()
clk: axm5516: Convert to devm_platform_ioremap_resource()
clk: actions: Convert to devm_platform_ioremap_resource()
clk: cdce925: Remove redundant of_match_ptr()
clk: pxa910: Move number of clocks to driver source
clk: pxa1928: Move number of clocks to driver source
clk: pxa168: Move number of clocks to driver source
clk: mmp2: Move number of clocks to driver source
...
* clk-qcom: (87 commits) clk: qcom: Fix SM_GPUCC_8450 dependencies clk: qcom: smd-rpm: Set XO rate and CLK_IS_CRITICAL on PCNoC clk: qcom: smd-rpm: Add a way to define bus clocks with rate and flags clk: qcom: gcc-ipq5018: change some variable static clk: qcom: gcc-ipq4019: add missing networking resets dt-bindings: clock: qcom: ipq4019: add missing networking resets clk: qcom: gcc-msm8917: Enable GPLL0_SLEEP_CLK_SRC dt-bindings: clock: gcc-msm8917: Add definition for GPLL0_SLEEP_CLK_SRC clk: qcom: gcc-qdu1000: Update the RCGs ops clk: qcom: gcc-qdu1000: Update the SDCC clock RCG ops clk: qcom: gcc-qdu1000: Add support for GDSCs clk: qcom: gcc-qdu1000: Add gcc_ddrss_ecpri_gsi_clk support clk: qcom: gcc-qdu1000: Register gcc_gpll1_out_even clock clk: qcom: gcc-qdu1000: Fix clkref clocks handling clk: qcom: gcc-qdu1000: Fix gcc_pcie_0_pipe_clk_src clock handling dt-bindings: clock: Update GCC clocks for QDU1000 and QRU1000 SoCs clk: qcom: gcc-sm8450: Use floor ops for SDCC RCGs clk: qcom: ipq5332: drop the gcc_apss_axi_clk_src clock clk: qcom: ipq5332: drop the mem noc clocks clk: qcom: gcc-msm8998: Don't check halt bit on some branch clks ...
- Add __counted_by to struct clk_hw_onecell_data and struct spmi_pmic_div_clk_cc - Remove non-OF mmp clk drivers - Move number of clks from DT headers to drivers * clk-imx: clk: imx: pll14xx: dynamically configure PLL for 393216000/361267200Hz clk: imx: pll14xx: align pdiv with reference manual clk: imx: composite-8m: fix clock pauses when set_rate would be a no-op clk: imx25: make __mx25_clocks_init return void clk: imx25: print silicon revision during init dt-bindings: clocks: imx8mp: make sai4 a dummy clock clk: imx8mp: fix sai4 clock clk: imx: imx8ulp: update SPLL2 type clk: imx: pllv4: Fix SPLL2 MULT range clk: imx: imx8: add audio clock mux driver dt-bindings: clock: fsl,imx8-acm: Add audio clock mux support clk: imx: clk-imx8qxp-lpcg: Convert to devm_platform_ioremap_resource() clk: imx: clk-gpr-mux: Simplify .determine_rate() clk: imx: Add 519.75MHz frequency support for imx9 pll clk: imx93: Add PDM IPG clk dt-bindings: clock: imx93: Add PDM IPG clk * clk-samsung: dt-bindings: clock: samsung: remove define with number of clocks clk: samsung: exynoautov9: do not define number of clocks in bindings clk: samsung: exynos850: do not define number of clocks in bindings clk: samsung: exynos7885: do not define number of clocks in bindings clk: samsung: exynos5433: do not define number of clocks in bindings clk: samsung: exynos5420: do not define number of clocks in bindings clk: samsung: exynos5410: do not define number of clocks in bindings clk: samsung: exynos5260: do not define number of clocks in bindings clk: samsung: exynos5250: do not define number of clocks in bindings clk: samsung: exynos4: do not define number of clocks in bindings clk: samsung: exynos3250: do not define number of clocks in bindings * clk-annotate: clk: qcom: clk-spmi-pmic-div: Annotate struct spmi_pmic_div_clk_cc with __counted_by clk: Annotate struct clk_hw_onecell_data with __counted_by * clk-marvell: clk: pxa910: Move number of clocks to driver source clk: pxa1928: Move number of clocks to driver source clk: pxa168: Move number of clocks to driver source clk: mmp2: Move number of clocks to driver source clk: mmp: Remove old non-OF clock drivers * clk-lmk: clk: lmk04832: Support using PLL1_LD as SPI readback pin clk: lmk04832: Don't disable vco clock on probe fail clk: lmk04832: Set missing parent_names for output clocks