Fixes for omaps for v5.4-rc cycle Here are fixes for omaps to deal with few regressions, and to fix more boot time errors and warnings: - The recent ti-sysc interconnect target module driver changes had incorrect clock bits for both clocks and dts that cause warnings - For omap3-gta04, gpio changes caused the LCD to break a while back, and after discussing things the right fix is to set spi-cs-high - Recent omapdrm changes to use generic panels caused tfp410 to be disabled as we now must enable the generic support for it in defconfig - Recent omapdrm and backlight changes also finally made droid4 LCD to work, so let's enable it in the defconfig it can be used out of the box. This is not strictly a fix, but we still also have the older CONFIG_MFD_TI_LMU options available so this cuts down the confusion for trying to guess which display and which backlight is needed - Recent ti-sysc interconnect target module changes need the gpio module disabled on some boards, but this now needs to happen at the module level, not at the gpio driver level - Recent changes to probe system timers with ti-sysc caused warnings about mismatch in syconfig registers, so let's configure the option for RESET_STATUS as available in the TRMs - Recent changes to probe LCDC with ti-sysc caused warnings about mismatch in sysconfig registers, so let's configure the missing idlemodes for both platform data and dts as documented in TRMs - Since we moved mach-omap2 to probe with device tree, we've been getting voltage controller warnings. Turns out this code is no longer needed, so let's just remove omap2_set_init_voltage() to get rid of the pointless warnings - Configure am4372 dispc memory bandwidth to avoid underflow errors * tag 'omap-for-v5.4/fixes-rc1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: dts: am4372: Set memory bandwidth limit for DISPC ARM: OMAP2+: Fix warnings with broken omap2_set_init_voltage() ARM: OMAP2+: Add missing LCDC midlemode for am335x ARM: OMAP2+: Fix missing reset done flag for am3 and am43 ARM: dts: Fix gpio0 flags for am335x-icev2 ARM: omap2plus_defconfig: Enable more droid4 devices as loadable modules ARM: omap2plus_defconfig: Enable DRM_TI_TFP410 DTS: ARM: gta04: introduce legacy spi-cs-high to make display work again ARM: dts: Fix wrong clocks for dra7 mcasp clk: ti: dra7: Fix mcasp8 clock bits Link: https://lore.kernel.org/r/pull-1570040410-308159@atomide.com Signed-off-by: Olof Johansson <olof@lixom.net>
There's a typo for dra7 mcasp clkctrl bit, it should be 22 like the other
macasp instances, and not 24. And in dra7xx_clks[] we have the bits wrong
way around.
Fixes: dffa9051d546 ("clk: ti: dra7: add new clkctrl data")
Cc: linux-clk@vger.kernel.org
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Suman Anna <s-anna@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull MIPS updates from Paul Burton:
"Main MIPS changes:
- boot_mem_map is removed, providing a nice cleanup made possible by
the recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs
or MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of
Vincenzo Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic
SoCs.
- pte_special() is now supported for some configurations, allowing
among other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil,
mostly enabled by the inclusion of the new TCU (timer-counter unit)
drivers he's spent a very patient year or so working on. Plus some
fixes for X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems"
* tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (89 commits)
MIPS: Detect bad _PFN_SHIFT values
MIPS: Disable pte_special() for MIPS32 with RiXi
MIPS: ralink: deactivate PCI support for SOC_MT7621
mips: compat: vdso: Use legacy syscalls as fallback
MIPS: Drop Loongson _CACHE_* definitions
MIPS: tlbex: Remove cpu_has_local_ebase
MIPS: tlbex: Simplify r3k check
MIPS: Select R3k-style TLB in Kconfig
MIPS: PCI: refactor ioc3 special handling
mips: remove ioremap_cachable
mips/atomic: Fix smp_mb__{before,after}_atomic()
mips/atomic: Fix loongson_llsc_mb() wreckage
mips/atomic: Fix cmpxchg64 barriers
MIPS: Octeon: remove duplicated include from dma-octeon.c
firmware: bcm47xx_nvram: Allow COMPILE_TEST
firmware: bcm47xx_nvram: Correct size_t printf format
MIPS: Treat Loongson Extensions as ASEs
MIPS: Remove dev_err() usage after platform_get_irq()
MIPS: dts: mscc: describe the PTP ready interrupt
MIPS: dts: mscc: describe the PTP register range
...
Pull ARM SoC late updates from Arnd Bergmann:
"This is some material that we picked up into our tree late or that had
complex inter-depondencies. The fact that there are these
interdependencies tends to meant that these are often actually the
most interesting new additions:
- The new Aspeed AST2600 baseboard management controller is added,
this is a Cortex-A7 based follow-up to the ARM11 based AST2500 and
had some dependencies on other device drivers.
- After many years, support for the MMP2 based OLPC XO-1.75 finally
makes it into the kernel.
- The Armada 3720 based Turris Mox open source router platform is a
late addition and it follows some preparatory work across multiple
branches.
- The OMAP2+ platform had some large-scale cleanup involving driver
changes and DT changes, here we finish it off, dropping a lot of
the now-unused platform data.
- The TI K3 platform that got added for 5.3 gains a lot more support
for individual bits on the SoC, this part just came late for the
merge window"
[ This pull request itself wasn't actually sent late at all by Arnd, but
I waited on the branches that it used to be pulled first, so it ends
up being merged much later than the other ARM SoC pull requests this
merge window - Linus ]
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (57 commits)
ARM: dts: dir685: Drop spi-cpol from the display
ARM: dts: aspeed: Add AST2600 pinmux nodes
ARM: dts: aspeed: Add AST2600 and EVB
ARM: exynos: Enable support for ARM architected timers
ARM: samsung: Fix system restart on S3C6410
ARM: dts: mmp2: add OLPC XO 1.75 machine
ARM: dts: mmp2: rename the USB PHY node
ARM: dts: mmp2: specify reg-shift for the UARTs
ARM: dts: mmp2: add camera interfaces
ARM: dts: mmp2: fix the SPI nodes
ARM: dts: mmp2: trivial whitespace fix
arm64: dts: marvell: add DTS for Turris Mox
dt-bindings: marvell: document Turris Mox compatible
arm64: dts: marvell: armada-37xx: add SPI CS1 pinctrl
arm64: dts: ti: k3-j721e-main: Fix gic-its node unit-address
arm64: dts: ti: k3-am65-main: Fix gic-its node unit-address
arm64: dts: ti: k3-j721e-main: Add hwspinlock node
arm64: dts: ti: k3-am65-main: Add hwspinlock node
arm64: dts: k3-j721e: Add gpio-keys on common processor board
dt-bindings: pinctrl: k3: Introduce pinmux definitions for J721E
...
Pull clk updates from Stephen Boyd: "We have a small collection of core framework updates this time, mostly around clk registration by clk providers and debugfs "nice to haves" for rate constraints. I'll highlight that we're now setting the clk_init_data pointer inside struct clk_hw to NULL during clk_register(), which may break some drivers that thought they could use that pointer during normal operations. That change has been sitting in next for a while now but maybe something is still broken. We'l see. Other than that the core framework changes aren't invasive and they're fixing bugs, simplifying, and making things better. On the clk driver side we got the usual addition of new SoC support, new features for existing drivers, and bug fixes scattered throughout. The biggest diffstat is the Amlogic driver that gained CPU clk support in addition to migrating to the new way of specifying clk parents. After that the Qualcomm, i.MX, Mediatek, and Rockchip clk drivers got support for various new SoCs and clock controllers from those vendors. Core: - Drop NULL checks in clk debugfs - Add min/max rates to clk debugfs - Set clk_init_data pointer inside clk_hw to NULL after registration - Make clk_bulk_get_all() return an 'id' corresponding to clock-names - Evict parents from parent cache when they're unregistered New Drivers: - Add clock driver for i.MX8MN SoCs - Support aspeed AST2600 SoCs - Support for Mediatek MT6779 SoCs - Support qcom SM8150 GCC and RPMh clks - Support qcom QCS404 WCSS clks - Add CPU clock support for Armada 7K/8K (specifically AP806 and AP807) - Addition of clock driver for Rockchip rk3308 SoCs Updates: - Add regulator support to the cdce925 clk driver - Add support for Raspberry Pi 4 bcm2711 SoCs - Add SDIO gate support to aspeed driver - Add missing of_node_put() calls in various clk drivers - Migrate Amlogic driver to new clock parent description method - Add DVFS support to Amlogic Meson g12 - Add Amlogic Meson g12a reset support to the axg audio clock controller - Add sm1 support to the Amlogic Meson g12a clock controller - Switch i.MX8MM clock driver to platform driver - Add Hifi4 DSP related clocks for i.MX8QXP SoC - Fix Audio PLL setting and parent clock for USB - Misc i.MX8 clock driver improvements and corrections - Set floor ops for Qualcomm SD clks so that rounding works - Fix "always-on" Clock Domains on Renesas R-Car M1A, RZ/A1, RZ/A2, and RZ/N1 - Enable the Allwinner V3 SoC and fix the i2s clock for H6" * tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (137 commits) clk: Drop !clk checks in debugfs dumping clk: imx: imx8mn: fix pll mux bit clk: imx: imx8mm: fix pll mux bit clk: imx: clk-pll14xx: unbypass PLL by default clk: imx: pll14xx: avoid glitch when set rate clk: mvebu: ap80x: add AP807 clock support clk: mvebu: ap806: Prepare the introduction of AP807 clock support clk: mvebu: ap806: add AP-DCLK (hclk) to system controller driver clk: mvebu: ap806: be more explicit on what SaR is clk: mvebu: ap80x-cpu: add AP807 CPU clock support clk: mvebu: ap806-cpu: prepare mapping of AP807 CPU clock dt-bindings: ap806: Document AP807 clock compatible dt-bindings: ap80x: Document AP807 CPU clock compatible clk: sprd: add missing kfree clk: at91: allow 24 Mhz clock as input for PLL clk: Make clk_bulk_get_all() return a valid "id" clk: actions: Fix factor clk struct member access clk: qcom: rcg: Return failure for RCG update clk: remove extra ---help--- tags in Kconfig clk: add include guard to clk-conf.h ...
- Make clk_bulk_get_all() return an 'id' corresponding to clock-names * clk-bulk-fix: clk: Make clk_bulk_get_all() return a valid "id" * clk-at91: clk: at91: allow 24 Mhz clock as input for PLL clk: at91: select parent if main oscillator or bypass is enabled clk: at91: fix update bit maps on CFG_MOR write * clk-sprd: clk: sprd: add missing kfree
- Add regulator support to the cdce925 clk driver - Add support for Raspberry Pi 4 bcm2711 SoCs - Evict parents from parent cache when they're unregistered * clk-cdce-regulator: clk: clk-cdce925: Add regulator support dt-bindings: clock: cdce925: Add regulator documentation * clk-bcm: clk: bcm2835: Mark PLLD_PER as CRITICAL clk: bcm2835: Add BCM2711_CLOCK_EMMC2 support clk: bcm2835: Introduce SoC specific clock registration dt-bindings: bcm2835-cprman: Add bcm2711 support * clk-evict-parent-cache: clk: Evict unregistered clks from parent caches * clk-actions: clk: actions: Fix factor clk struct member access
* clk-renesas: clk: renesas: cpg-mssr: Set GENPD_FLAG_ALWAYS_ON for clock domain clk: renesas: r9a06g032: Set GENPD_FLAG_ALWAYS_ON for clock domain clk: renesas: mstp: Set GENPD_FLAG_ALWAYS_ON for clock domain dt-bindings: clk: emev2: Rename bindings documentation file clk: renesas: rcar-usb2-clock-sel: Use devm_platform_ioremap_resource() helper * clk-rockchip: clk: rockchip: Add clock controller for the rk3308 clk: rockchip: Add dt-binding header for rk3308 dt-bindings: Add bindings for rk3308 clock controller clk: rockchip: Fix -Wunused-const-variable in rv1108 clk driver * clk-const: clk: spear: Make structure i2s_sclk_masks constant * clk-simplify: clk/ti: Use kmemdup rather than duplicating its implementation clk: fix devm_platform_ioremap_resource.cocci warnings
- Set clk_init_data pointer inside clk_hw to NULL after registration * clk-init-destroy: clk: Overwrite clk_hw::init with NULL during clk_register() clk: sunxi: Don't call clk_hw_get_name() on a hw that isn't registered clk: ti: Don't reference clk_init_data after registration clk: qcom: Remove error prints from DFS registration rtc: sun6i: Don't reference clk_init_data after registration clk: zx296718: Don't reference clk_init_data after registration clk: milbeaut: Don't reference clk_init_data after registration clk: socfpga: deindent code to proper indentation phy: ti: am654-serdes: Don't reference clk_init_data after registration clk: sprd: Don't reference clk_init_data after registration clk: socfpga: Don't reference clk_init_data after registration clk: sirf: Don't reference clk_init_data after registration clk: qcom: Don't reference clk_init_data after registration clk: meson: axg-audio: Don't reference clk_init_data after registration clk: lochnagar: Don't reference clk_init_data after registration clk: actions: Don't reference clk_init_data after registration * clk-doc: clk: remove extra ---help--- tags in Kconfig clk: add include guard to clk-conf.h clk: Document of_parse_clkspec() some more clk: Remove extraneous 'for' word in comments * clk-imx: (32 commits) clk: imx: imx8mn: fix pll mux bit clk: imx: imx8mm: fix pll mux bit clk: imx: clk-pll14xx: unbypass PLL by default clk: imx: pll14xx: avoid glitch when set rate clk: imx: imx8mn: fix audio pll setting clk: imx8mn: Add necessary frequency support for ARM PLL table clk: imx8mn: Add missing rate_count assignment for each PLL structure clk: imx8mn: fix int pll clk gate clk: imx8mn: Add GIC clock clk: imx8mn: Fix incorrect parents clk: imx8mm: Fix incorrect parents clk: imx8mq: Fix sys3 pll references clk: imx8mq: Unregister clks when of_clk_add_provider failed clk: imx8mm: Unregister clks when of_clk_add_provider failed clk: imx8mq: Mark AHB clock as critical clk: imx8mn: Keep uart clocks on for early console clk: imx: Remove unused function statement clk: imx7ulp: Make sure earlycon's clock is enabled clk: imx8mm: Switch to platform driver clk: imx: imx8mm: fix audio pll setting ... * clk-allwinner: clk: sunxi-ng: h6: Allow I2S to change parent rate clk: sunxi-ng: v3s: add Allwinner V3 support clk: sunxi-ng: v3s: add missing clock slices for MMC2 module clocks dt-bindings: clk: sunxi-ccu: add compatible string for V3 CCU clk: sunxi-ng: v3s: add the missing PLL_DDR1
- Support qcom SM8150 RPMh clks - Set floor ops for qcom sd clks - Support qcom QCS404 WCSS clks - Support for Mediatek MT6779 SoCs - Add CPU clock support for Armada 7K/8K (specifically AP806 and AP807) * clk-qcom: clk: qcom: rcg: Return failure for RCG update clk: qcom: fix QCS404 TuringCC regmap clk: qcom: clk-rpmh: Add support for SM8150 dt-bindings: clock: Document SM8150 rpmh-clock compatible clk: qcom: clk-rpmh: Convert to parent data scheme dt-bindings: clock: Document the parent clocks clk: qcom: gcc: Use floor ops for SDCC clocks clk: qcom: gcc-qcs404: Use floor ops for sdcc clks clk: qcom: gcc-sdm845: Use floor ops for sdcc clks clk: qcom: define probe by index API as common API clk: qcom: Add WCSS gcc clock control for QCS404 clk: qcom: msm8916: Don't build by default clk: qcom: gcc: Add global clock controller driver for SM8150 dt-bindings: clock: Document gcc bindings for SM8150 clk: qcom: clk-alpha-pll: Add support for Trion PLLs clk: qcom: clk-alpha-pll: Remove post_div_table checks clk: qcom: clk-alpha-pll: Remove unnecessary cast * clk-mtk: clk: mediatek: Runtime PM support for MT8183 mcucfg clock provider clk: mediatek: Register clock gate with device clk: mediatek: add pericfg clocks for MT8183 dt-bindings: clock: mediatek: add pericfg for MT8183 clk: mediatek: Add MT6779 clock support clk: mediatek: Add dt-bindings for MT6779 clocks dt-bindings: mediatek: bindings for MT6779 clk clk: reset: Modify reset-controller driver * clk-armada: clk: mvebu: ap80x: add AP807 clock support clk: mvebu: ap806: Prepare the introduction of AP807 clock support clk: mvebu: ap806: add AP-DCLK (hclk) to system controller driver clk: mvebu: ap806: be more explicit on what SaR is clk: mvebu: ap80x-cpu: add AP807 CPU clock support clk: mvebu: ap806-cpu: prepare mapping of AP807 CPU clock dt-bindings: ap806: Document AP807 clock compatible dt-bindings: ap80x: Document AP807 CPU clock compatible clk: mvebu: ap806: Fix clock name for the cluster clk: mvebu: add CPU clock driver for Armada 7K/8K clk: mvebu: add helper file for Armada AP and CP clocks dt-bindings: ap806: add the cluster clock node in the syscon file * clk-ingenic: clk: ingenic: Use CLK_OF_DECLARE_DRIVER macro clk: ingenic/jz4740: Fix "pll half" divider not read/written properly * clk-meson: (23 commits) clk: meson: g12a: add support for SM1 CPU 1, 2 & 3 clocks clk: meson: g12a: add support for SM1 DynamIQ Shared Unit clock clk: meson: g12a: add support for SM1 GP1 PLL dt-bindings: clk: meson: add sm1 periph clock controller bindings clk: meson: axg-audio: add g12a reset support dt-bindings: clock: meson: add resets to the audio clock controller clk: meson: g12a: expose CPUB clock ID for G12B clk: meson: g12a: add notifiers to handle cpu clock change clk: meson: add g12a cpu dynamic divider driver clk: core: introduce clk_hw_set_parent() clk: meson: remove clk input helper clk: meson: remove ee input bypass clocks clk: meson: clk-regmap: migrate to new parent description method clk: meson: meson8b: migrate to the new parent description method clk: meson: axg: migrate to the new parent description method clk: meson: gxbb: migrate to the new parent description method clk: meson: g12a: migrate to the new parent description method clk: meson: remove ao input bypass clocks clk: meson: axg-aoclk: migrate to the new parent description method clk: meson: gxbb-aoclk: migrate to the new parent description method ...