Pull ARM DT updates from Olof Johansson:
 "Device tree contents continue to be the largest branches we submit.
  This time around, some of the contents worth pointing out is:

  New SoC platforms:
   - Freescale i.MX 7Solo
   - Broadcom BCM23550
   - Cirrus Logic EP7209 and EP7211 (clps711x platforms)_
   - Hisilicon HI3519
   - Renesas R8A7792

  Some of the other delta that is sticking out, line-count wise:
   - Exynos moves of IP blocks under an SoC bus, which causes a large
     delta due to indentation changes
   - a new Tegra K1 board: Apalis
   - a bunch of small updates to many Allwinner platforms; new hardware
     support, some cleanup, etc"

* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (426 commits)
  ARM: dts: sun8i: Add dts file for inet86dz board
  ARM: dts: sun8i: Add dts file for Polaroid MID2407PXE03 tablet
  ARM: dts: sun8i: Use sun8i-reference-design-tablet for ga10h dts
  ARM: dts: sun8i: Use sun8i-reference-design-tablet for polaroid mid2809pxe04
  ARM: dts: sun8i: reference-design-tablet: Add drivevbus-supply
  ARM: dts: Copy sun8i-q8-common.dtsi sun8i-reference-design-tablet.dtsi
  ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for utoo p66 dts
  ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for dit4350 dts
  ARM: dts: sun5i: reference-design-tablet: Remove mention of q8
  ARM: dts: sun5i: reference-design-tablet: Set lradc vref to avcc
  ARM: dts: sun5i: Rename sun5i-q8-common.dtsi sun5i-reference-design-tablet.dtsi
  ARM: dts: sun5i: Move q8 display bits to sun5i-a13-q8-tablet.dts
  ARM: dts: sunxi: Rename sunxi-q8-common.dtsi sunxi-reference-design-tablet.dtsi
  ARM: dts: at91: Don't build unnecessary dtbs
  ARM: dts: at91: sama5d3x: separate motherboard gmac and emac definitions
  ARM: dts: at91: at91sam9g25ek: fix isi endpoint node
  ARM: dts: at91: move isi definition to at91sam9g25ek
  ARM: dts: at91: fix i2c-gpio node name
  ARM: dts: at91: vinco: fix regulator name
  ARM: dts: at91: ariag25 : fix onewire node
  ...

Add clk node for RNG module.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add tblck to the pwm nodes. This insures that the ehrpwm driver has access
to the time-based clk.

Do not remove similar entries for ehrpwm node. Later patches will switch
from using ehrpwm node name to pwm. But to maintain ABI compatibility we
shouldn't remove the old entries.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Pull clk updates from Stephen Boyd:
 "It's the usual big pile of driver updates and additions, but we do
  have a couple core changes in here as well.

  Core:

   - CLK_IS_CRITICAL support has been added.  This should allow drivers
     to properly express that a certain clk should stay on even if their
     prepare/enable count drops to 0 (and in turn the parents of these
     clks should stay enabled).

   - A clk registration API has been added, clk_hw_register(), and an OF
     clk provider API has been added, of_clk_add_hw_provider().  These
     APIs have been put in place to further split clk providers from clk
     consumers, with the goal being to have clk providers never deal
     with struct clk pointers at all.  Conversion of provider drivers is
     on going.  clkdev has also gained support for registering clk_hw
     pointers directly so we can convert drivers that don't use
     devicetree.

  New Drivers:

   - Marvell ap806 and cp110 system controllers (with clks inside!)
   - Hisilicon Hi3519 clock and reset controller
   - Axis ARTPEC-6 clock controllers
   - Oxford Semiconductor OXNAS clock controllers
   - AXS10X I2S PLL
   - Rockchip RK3399 clock and reset controller

  Updates:

   - MMC2 and UART2 clks on Samsung Exynos 3250, ACLK on Samsung Exynos
     542x SoCs, and some more clk ID exporting for bus frequency scaling
   - Proper BCM2835 PCM clk support and various other clks
   - i.MX clk updates for i.MX6SX, i.MX7, and VF610
   - Renesas updates for R-Car H3
   - Tegra210 got updates for DisplayPort and HDMI 2.0
   - Rockchip driver refactorings and fixes due to adding RK3399 support"

* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (139 commits)
  clk: fix critical clock locking
  clk: qcom: mmcc-8996: Remove clocks that should be controlled by RPM
  clk: ingenic: Allow divider value to be divided
  clk: sunxi: Add display and TCON0 clocks driver
  clk: rockchip: drop old_rate calculation on pll rate changes
  clk: rockchip: simplify GRF handling in pll clocks
  clk: rockchip: lookup General Register Files in rockchip_clk_init
  clk: rockchip: fix the rk3399 sdmmc sample / drv name
  clk: mvebu: new driver for Armada CP110 system controller
  dt-bindings: arm: add DT binding for Marvell CP110 system controller
  clk: mvebu: new driver for Armada AP806 system controller
  clk: hisilicon: add CRG driver for hi3519 soc
  clk: hisilicon: export some hisilicon APIs to modules
  reset: hisilicon: add reset controller driver for hisilicon SOCs
  clk: bcm/kona: Do not use sizeof on pointer type
  clk: qcom: msm8916: Fix crypto clock flags
  clk: nxp: lpc18xx: Initialize clk_init_data::flags to 0
  clk/axs10x: Add I2S PLL clock driver
  clk: imx7d: fix ahb clock mux 1
  clk: fix comment of devm_clk_hw_register()
  ...

of_find_node_by_name() will call of_node_put() on the node so we need to
get it first to avoid warnings.
The cfg_node needs to be put after we have finished processing the
properties.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

The OMAP Platform code provides possibility to select GP Timer as
default clocksource instead of counter_32K by using bootcmd parameter
'clocksource', but the system will crash during early boot when this
option is used on dra7 or omap5 platforms, because it will hit BUG()
statement:

 omap2_gptimer_clocksource_init
  ->BUG_ON(res);

This happens because clk_dev alias "sys_clkin_ck" is not registered.
Hence, fix it by adding missing "sys_clkin_ck" clk_dev aliases
definitions for omap5 and dra7.

Acked-by: Tero Kristo <t-kristo@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

AM33xx/AM43xx devices use the same DPLL IP blocks, which only support
maximum rate of 1GHz [1] for the default and 2GHz for the low-jitter type
DPLLs [2]. Reflect this limitation in the DPLL init code by adding the
max-rate parameter based on the DPLL types.

[1] Functional, integration & test specification for GS70 ADPLLS, Rev 1.0-01
[2] Functional, integration & test specification for GS70 ADPLLLJ, Rev 0.8-02

Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

DPLLs typically have a maximum rate they can support, and this varies
from DPLL to DPLL. Add support of the maximum rate value to the DPLL
data struct, and also add check for this in the DPLL round_rate function.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Commit 7aba4f5201d1 ("clk: ti: dflt: fix enable_reg validity check")
fixed a validation check by using an IS_ERR() macro within the
existing unlikely expression, but IS_ERR() macro already has an
unlikely inside it, so get rid of the redundant unlikely macro
from the validation check.

Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

rename the mcasp8_ahclk_mux to mcasp8_ahclkx_mux.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated for the unit offsets]
Signed-off-by: Tony Lindgren <tony@atomide.com>