linux.git/drivers/clk/sunxi, branch v4.1

clk: sunxi: Add pll6 / 4 clock output to sun4i-a10-pll6

2015-03-25T18:46:41+00:00

The pll6 has a /4 output that is used as an input to the ahb mux clock.

Signed-off-by: Chen-Yu Tsai 
Signed-off-by: Maxime Ripard

clk: sunxi: Make divs clocks specify which output is the base factor clock

2015-03-25T18:46:32+00:00

The current sunxi clock driver has the base factor clock of divs clocks
as the last clock output of the clock node. This makes it rather difficult
to add new outputs, such as fixed dividers, which were previously unknown.

This patch makes the divs clocks data structure specify which output is
the factor clock, and updates all current divs clocks accordingly.

We can then add new outputs after the factor clocks, at least not breaking
backward compatibility with regards to the devicetree bindings.

Also replace kzalloc with kcalloc in sunxi_divs_clk_setup().

Signed-off-by: Chen-Yu Tsai 
Signed-off-by: Maxime Ripard

clk: sunxi: Register divs clocks before factor clocks

2015-03-21T10:49:57+00:00

We want to reparent AHB clock to PLL6 on sun5i/sun7i using the assigned
clocks properties. AHB is a factor clock, while PLL6 is a divs clock.

Register divs clocks before factor clocks so reparenting works. This
is only needed because we do the reparenting on the clock provider.

The proper way to fix this is to split out all the old sunxi clocks
into separate CLK_OF_DECLARE statements, like we are doing for sun9i.

Signed-off-by: Chen-Yu Tsai 
Signed-off-by: Maxime Ripard

clk: sunxi: Add "cpu" to list of protected clocks for sun5i

2015-03-21T10:49:21+00:00

Now that the ahb clock on sun5i/sun7i is muxable, ahb is no longer
guaranteed to be a child of the cpu clock. Add the cpu clock to
the list of protected clocks so it doesn't get disabled.

Signed-off-by: Chen-Yu Tsai 
Signed-off-by: Maxime Ripard

clk: sunxi: Add muxable ahb factors clock for sun5i and sun7i

2015-03-21T10:48:40+00:00

The AHB clock on sun5i and sun7i are muxable divider clocks.
Use a factors clock to support them.

Signed-off-by: Chen-Yu Tsai 
Signed-off-by: Maxime Ripard

clk: sunxi: Add support for sun9i A80 USB clocks and resets

2015-02-23T08:25:54+00:00

The USB controller/phy clocks and reset controls are in a separate
address block, unlike previous SoCs where they were in the clock
controller. Also, access to the address block is controlled by a
clock gate to AHB.

Add support for resets requiring a clock to be enabled when
asserting/deasserting the reset controls, and add the sun9i USB
clocks.

Signed-off-by: Chen-Yu Tsai 
Signed-off-by: Maxime Ripard

clk: sunxi: Move USB clocks to separate file

2015-02-23T08:25:54+00:00

The USB clocks originally shared code with the gates clocks, but had
additional reset controllers. Move these to a separate file. This will
allow us to add new support for slightly different USB clocks, such as
on the A80, without affecting gates clocks, and also facilitate the
migration of gates clocks to a generic solution.

This also cleans up the USB clocks code slightly, such as adding
newlines, getting rid of the unused clkdev call, using a simple
u32 instead of BITMAP for the clock masks, using BIT() macro to
declare the clock bitmasks, and using of_io_request_and_map() to
get the I/O address.

Signed-off-by: Chen-Yu Tsai 
Signed-off-by: Maxime Ripard

Merge tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux

2015-02-21T20:30:30+00:00

Pull clock framework updates from Mike Turquette:
 "The clock framework changes contain the usual driver additions,
  enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
  devices.

  Additionally the framework core underwent a bit of surgery with two
  major changes:

   - The boundary between the clock core and clock providers (e.g clock
     drivers) is now more well defined with dedicated provider helper
     functions.  struct clk no longer maps 1:1 with the hardware clock
     but is a true per-user cookie which helps us tracker users of
     hardware clocks and debug bad behavior.

   - The addition of rate constraints for clocks.  Rate ranges are now
     supported which are analogous to the voltage ranges in the
     regulator framework.

  Unfortunately these changes to the core created some breakeage.  We
  think we fixed it all up but for this reason there are lots of last
  minute commits trying to undo the damage"

* tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux: (113 commits)
  clk: Only recalculate the rate if needed
  Revert "clk: mxs: Fix invalid 32-bit access to frac registers"
  clk: qoriq: Add support for the platform PLL
  powerpc/corenet: Enable CLK_QORIQ
  clk: Replace explicit clk assignment with __clk_hw_set_clk
  clk: Add __clk_hw_set_clk helper function
  clk: Don't dereference parent clock if is NULL
  MIPS: Alchemy: Remove bogus args from alchemy_clk_fgcs_detr
  clkdev: Always allocate a struct clk and call __clk_get() w/ CCF
  clk: shmobile: div6: Avoid division by zero in .round_rate()
  clk: mxs: Fix invalid 32-bit access to frac registers
  clk: omap: compile legacy omap3 clocks conditionally
  clkdev: Export clk_register_clkdev
  clk: Add rate constraints to clocks
  clk: remove clk-private.h
  pci: xgene: do not use clk-private.h
  arm: omap2+ remove dead clock code
  clk: Make clk API return per-user struct clk instances
  clk: tegra: Define PLLD_DSI and remove dsia(b)_mux
  clk: tegra: Add support for the Tegra132 CAR IP block
  ...

clk: Add rate constraints to clocks

2015-02-02T22:23:42+00:00

Adds a way for clock consumers to set maximum and minimum rates. This
can be used for thermal drivers to set minimum rates, or by misc.
drivers to set maximum rates to assure a minimum performance level.

Changes the signature of the determine_rate callback by adding the
parameters min_rate and max_rate.

Signed-off-by: Tomeu Vizoso 
Signed-off-by: Stephen Boyd 
[sboyd@codeaurora.org: set req_rate in __clk_init]
Signed-off-by: Michael Turquette 
[mturquette@linaro.org: min/max rate for sun6i_ahb1_clk_determine_rate
                        migrated clk-private.h changes to clk.c]

sunxi: clk: Set sun6i-pll1 n_start = 1

2015-01-25T15:55:25+00:00

For all pll-s on sun6i n == 0 means use a multiplier of 1, rather then 0 as
it means on sun4i / sun5i / sun7i. n_start = 1 is already correctly set
for sun6i pll6, but was missing for pll1, this commit fixes this.

Cc: Chen-Yu Tsai 
Signed-off-by: Hans de Goede 
Signed-off-by: Maxime Ripard