linux.git/drivers/char, branch v5.8-rc4

tpm_tis: Remove the HID IFX0102

2020-07-02T14:49:00+00:00

Acer C720 running Linux v5.3 reports this in klog:

tpm_tis: 1.2 TPM (device-id 0xB, rev-id 16)
tpm tpm0: tpm_try_transmit: send(): error -5
tpm tpm0: A TPM error (-5) occurred attempting to determine the timeouts
tpm_tis tpm_tis: Could not get TPM timeouts and durations
tpm_tis 00:08: 1.2 TPM (device-id 0xB, rev-id 16)
tpm tpm0: tpm_try_transmit: send(): error -5
tpm tpm0: A TPM error (-5) occurred attempting to determine the timeouts
tpm_tis 00:08: Could not get TPM timeouts and durations
ima: No TPM chip found, activating TPM-bypass!
tpm_inf_pnp 00:08: Found TPM with ID IFX0102

% git --no-pager grep IFX0102 drivers/char/tpm
drivers/char/tpm/tpm_infineon.c:	{"IFX0102", 0},
drivers/char/tpm/tpm_tis.c:	{"IFX0102", 0},		/* Infineon */

Obviously IFX0102 was added to the HID table for the TCG TIS driver by
mistake.

Fixes: 93e1b7d42e1e ("[PATCH] tpm: add HID module parameter")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203877
Cc: stable@vger.kernel.org
Cc: Kylene Jo Hall 
Reported-by: Ferry Toth: 
Reviewed-by: Jerry Snitselaar 
Signed-off-by: Jarkko Sakkinen

tpm_tis_spi: Prefer async probe

2020-07-02T14:49:00+00:00

On a Chromebook I'm working on I noticed a big (~1 second) delay
during bootup where nothing was happening.  Right around this big
delay there were messages about the TPM:

[    2.311352] tpm_tis_spi spi0.0: TPM ready IRQ confirmed on attempt 2
[    3.332790] tpm_tis_spi spi0.0: Cr50 firmware version: ...

I put a few printouts in and saw that tpm_tis_spi_init() (specifically
tpm_chip_register() in that function) was taking the lion's share of
this time, though ~115 ms of the time was in cr50_print_fw_version().

Let's make a one-line change to prefer async probe for tpm_tis_spi.
There's no reason we need to block other drivers from probing while we
load.

NOTES:
* It's possible that other hardware runs through the init sequence
  faster than Cr50 and this isn't such a big problem for them.
  However, even if they are faster they are still doing _some_
  transfers over a SPI bus so this should benefit everyone even if to
  a lesser extent.
* It's possible that there are extra delays in the code that could be
  optimized out.  I didn't dig since once I enabled async probe they
  no longer impacted me.

Signed-off-by: Douglas Anderson 
Reviewed-by: Jarkko Sakkinen 
Signed-off-by: Jarkko Sakkinen

tpm: ibmvtpm: Wait for ready buffer before probing for TPM2 attributes

2020-07-02T14:49:00+00:00

The tpm2_get_cc_attrs_tbl() call will result in TPM commands being issued,
which will need the use of the internal command/response buffer.  But,
we're issuing this *before* we've waited to make sure that buffer is
allocated.

This can result in intermittent failures to probe if the hypervisor / TPM
implementation doesn't respond quickly enough.  I find it fails almost
every time with an 8 vcpu guest under KVM with software emulated TPM.

To fix it, just move the tpm2_get_cc_attrs_tlb() call after the
existing code to wait for initialization, which will ensure the buffer
is allocated.

Fixes: 18b3670d79ae9 ("tpm: ibmvtpm: Add support for TPM2")
Signed-off-by: David Gibson 
Reviewed-by: Jerry Snitselaar 
Reviewed-by: Jarkko Sakkinen 
Signed-off-by: Jarkko Sakkinen

tpm/st33zp24: fix spelling mistake "drescription" -> "description"

2020-07-02T14:49:00+00:00

Trivial fix, the spelling of "drescription" is incorrect
in function comment.

Fix this.

Signed-off-by: Binbin Zhou 
Acked-by: Jarkko Sakkinen 
Signed-off-by: Jarkko Sakkinen

tpm_tis: extra chip->ops check on error path in tpm_tis_core_init

2020-07-02T14:49:00+00:00

Found by smatch:
drivers/char/tpm/tpm_tis_core.c:1088 tpm_tis_core_init() warn:
 variable dereferenced before check 'chip->ops' (see line 979)

'chip->ops' is assigned in the beginning of function
in tpmm_chip_alloc->tpm_chip_alloc
and is used before first possible goto to error path.

Signed-off-by: Vasily Averin 
Reviewed-by: Jerry Snitselaar 
Reviewed-by: Jarkko Sakkinen 
Signed-off-by: Jarkko Sakkinen

tpm_tis_spi: Don't send anything during flow control

2020-07-02T14:48:59+00:00

During flow control we are just reading from the TPM, yet our spi_xfer
has the tx_buf and rx_buf both non-NULL which means we're requesting a
full duplex transfer.

SPI is always somewhat of a full duplex protocol anyway and in theory
the other side shouldn't really be looking at what we're sending it
during flow control, but it's still a bit ugly to be sending some
"random" data when we shouldn't.

The default tpm_tis_spi_flow_control() tries to address this by
setting 'phy->iobuf[0] = 0'.  This partially avoids the problem of
sending "random" data, but since our tx_buf and rx_buf both point to
the same place I believe there is the potential of us sending the
TPM's previous byte back to it if we hit the retry loop.

Another flow control implementation, cr50_spi_flow_control(), doesn't
address this at all.

Let's clean this up and just make the tx_buf NULL before we call
flow_control().  Not only does this ensure that we're not sending any
"random" bytes but it also possibly could make the SPI controller
behave in a slightly more optimal way.

NOTE: no actual observed problems are fixed by this patch--it's was
just made based on code inspection.

Signed-off-by: Douglas Anderson 
Reviewed-by: Paul Menzel 
Reviewed-by: Jarkko Sakkinen 
Signed-off-by: Jarkko Sakkinen

tpm: Fix TIS locality timeout problems

2020-07-02T14:48:59+00:00

It has been reported that some TIS based TPMs are giving unexpected
errors when using the O_NONBLOCK path of the TPM device. The problem
is that some TPMs don't like it when you get and then relinquish a
locality (as the tpm_try_get_ops()/tpm_put_ops() pair does) without
sending a command.  This currently happens all the time in the
O_NONBLOCK write path. Fix this by moving the tpm_try_get_ops()
further down the code to after the O_NONBLOCK determination is made.
This is safe because the priv->buffer_mutex still protects the priv
state being modified.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206275
Fixes: d23d12484307 ("tpm: fix invalid locking in NONBLOCKING mode")
Reported-by: Mario Limonciello 
Tested-by: Alex Guzman 
Cc: stable@vger.kernel.org
Reviewed-by: Jerry Snitselaar 
Signed-off-by: James Bottomley 
Reviewed-by: Jarkko Sakkinen 
Signed-off-by: Jarkko Sakkinen

Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6

2020-06-21T17:01:03+00:00

Pull crypto fixes from Herbert Xu:

 - NULL dereference in octeontx

 - PM reference imbalance in ks-sa

 - deadlock in crypto manager

 - memory leak in drbg

 - missing socket limit check on receive SG list size in algif_skcipher

 - typos in caam

 - warnings in ccp and hisilicon

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: drbg - always try to free Jitter RNG instance
  crypto: marvell/octeontx - Fix a potential NULL dereference
  crypto: algboss - don't wait during notifier callback
  crypto: caam - fix typos
  crypto: ccp - Fix sparse warnings in sev-dev
  crypto: hisilicon - Cap block size at 2^31
  crypto: algif_skcipher - Cap recv SG list at ctx->used
  hwrng: ks-sa - Fix runtime PM imbalance on error

maccess: rename probe_kernel_{read,write} to copy_{from,to}_kernel_nofault

2020-06-17T17:57:41+00:00

Better describe what these functions do.

Suggested-by: Linus Torvalds 
Signed-off-by: Christoph Hellwig 
Signed-off-by: Linus Torvalds

hwrng: ks-sa - Fix runtime PM imbalance on error

2020-06-15T07:38:53+00:00

pm_runtime_get_sync() increments the runtime PM usage counter even
the call returns an error code. Thus a pairing decrement is needed
on the error handling path to keep the counter balanced.

Signed-off-by: Dinghao Liu 
Reviewed-by: Alexander Sverdlin 
Signed-off-by: Herbert Xu