Pull ARM SoC-related driver updates from Olof Johansson:
 "Various driver updates for platforms and a couple of the small driver
  subsystems we merge through our tree:

  Among the larger pieces:

   - Power management improvements for TI am335x and am437x (RTC
     suspend/wake)

   - Misc new additions for Amlogic (socinfo updates)

   - ZynqMP FPGA manager

   - Nvidia improvements for reset/powergate handling

   - PMIC wrapper for Mediatek MT8516

   - Misc fixes/improvements for ARM SCMI, TEE, NXP i.MX SCU drivers"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (57 commits)
  soc: aspeed: fix Kconfig
  soc: add aspeed folder and misc drivers
  spi: zynqmp: Fix build break
  soc: imx: Add generic i.MX8 SoC driver
  MAINTAINERS: Update email for Qualcomm SoC maintainer
  memory: tegra: Fix a typos for "fdcdwr2" mc client
  Revert "ARM: tegra: Restore memory arbitration on resume from LP1 on Tegra30+"
  memory: tegra: Replace readl-writel with mc_readl-mc_writel
  memory: tegra: Fix integer overflow on tick value calculation
  memory: tegra: Fix missed registers values latching
  ARM: tegra: cpuidle: Handle tick broadcasting within cpuidle core on Tegra20/30
  optee: allow to work without static shared memory
  soc/tegra: pmc: Move powergate initialisation to probe
  soc/tegra: pmc: Remove reset sysfs entries on error
  soc/tegra: pmc: Fix reset sources and levels
  soc: amlogic: meson-gx-pwrc-vpu: Add support for G12A
  soc: amlogic: meson-gx-pwrc-vpu: Fix power on/off register bitmask
  fpga manager: Adding FPGA Manager support for Xilinx zynqmp
  dt-bindings: fpga: Add bindings for ZynqMP fpga driver
  firmware: xilinx: Add fpga API's
  ...

For non legacy cases, add generic sysc_enable_module()
and sysc_disable_module() functions.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Detect DMIC to see what we have connected if config DEBUG is enabled.

Signed-off-by: Tony Lindgren <tony@atomide.com>

In preparation of dropping interconnect target module platform data in
favor of devicetree based data, we must pass swsup idle quirks to the
platform data functions.

For now, let's only tag the UART modules with the SWSUP_SIDLE_ACT quirk.
The other modules will get tagged with swsup quirks as we drop the
platform data and test the changes.

Signed-off-by: Tony Lindgren <tony@atomide.com>

We cannot access mcpdm registers at all unless there is an optional pdmclk
configured. As this is currently only needed for mcpdm, let's check for
mcpdm in sysc_get_clocks(). If it turns out to be needed for other modules
too, we can add more flags to the quirks table for this.

Signed-off-by: Tony Lindgren <tony@atomide.com>

At least mcpdm needs an optional external clock enabled to function and
this clock typically comes from the PMIC. We can detect mcpdm based on
the interconnect target module address and set a quirk flag early.

To do this, let's initialize the clocks a bit later and add a new
function for sysc_init_early_quirks(). Note that we cannot yet enable
the early quirks for mcpdm until the optional external clocks are
handled in the in the following patch.

Signed-off-by: Tony Lindgren <tony@atomide.com>

We can do the rsstctrl a bit later, but need to deassert rstctrl reset
before the clocks are enabled if asserted. Let's only init restctrl
in sysc_init_resets() and do the reset later on just before we enable
the device clocks.

Signed-off-by: Tony Lindgren <tony@atomide.com>

We are currently not managing interconnect target module clocks in the
for legacy platform data based case. This causes a problem for using the
platform data based functions when dropping the platform data for the
interconnect target module configuration.

To avoid a situation where we need to populate the main and optional
clocks also for the platform data based functions, let's just manage the
clocks directly in ti-sysc driver. This means that until the interconnect
target module confugration platform data is dropped our use count for
clk_enable() will be 2 instead of 1.

Signed-off-by: Tony Lindgren <tony@atomide.com>

The platform data based init functions typically reset the interconnect
target module configure the registers. As we may need the interconnect
target module specific quirks configured based on the revision register,
we want to move the platform data based init to happen later.

Let's allocate mdata as needed so it's available for sysc_legacy_init()
that we call with module clocks enabled from sysc_init_module().

Signed-off-by: Tony Lindgren <tony@atomide.com>

The first thing we want to do is just read the module revision register to
be able to configure the module specific quirks and configure the module
registers.

As the interconnect target module may not yet be properly configured and
may need a reset first, we don't want to use pm_runtime_get() at this
point.

To read the revision register, let's just enable the all the clocks for
the interconnect target module during init even if the optional clocks
are not needed. That way we can read the revision register to configure
the quirks needed for PM runtime.

Signed-off-by: Tony Lindgren <tony@atomide.com>