The MIPS Common Device Memory Map (CDMM) is internal to the core and has
native endianness. There is therefore no need to byte swap the accesses
on big endian targets, so convert the CDMM bus driver to use
__raw_readl() rather than readl().

Fixes: 8286ae03308c ("MIPS: Add CDMM bus support")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9904/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Currently in validate_group(), there is a static initializer
for fake_pmu.used_mask which is based on CPU_BITS_NONE but
the used_mask array size is based on CCI_PMU_MAX_HW_EVENTS.
CCI_PMU_MAX_HW_EVENTS is not based on NR_CPUS, so CPU_BITS_NONE
is not correct and will cause a build failure if NR_CPUS
is set high enough to make CPU_BITS_NONE larger than used_mask.

Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The L3 Error handling on OMAP5 for the most part is very similar
to that of OMAP4, and had leveraged common data structures and
register layout definitions so far. Upon closer inspection, there
are a few minor differences causing an incorrect decoding and
reporting of the master NIU upon an error:

  1. The L3_TARG_STDERRLOG_MSTADDR.STDERRLOG_MSTADDR occupies
     11 bits on OMAP5 as against 8 bits on OMAP4, with the master
     NIU connID encoded in the 6 MSBs of the STDERRLOG_MSTADDR
     field.
  2. The CLK3 FlagMux component has 1 input source on OMAP4 and 3
     input sources on OMAP5. The common DEBUGSS source is at a
     different input on each SoC.

Fix the above issues by using a OMAP5-specific compatible property
and using SoC-specific data where there are differences.

Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The base address for DRA7 CLK1_HOST_CLK1_2 host instance is
0x44800000, so correct offset is 0x800000. DRA7 TRM rev X(fewb 2015)
has updates for this information.

With wrong offset these errors are not correctly cleared by the L3
IRQ handler and cause an continuous interrupt scenario and system lockup.

Signed-off-by: Illia Smyrnov <illia.smyrnov@globallogic.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Pull ARM SoC driver updates from Olof Johansson:
 "Driver updates for v4.1.  Some of these are for drivers/soc, where we
  find more and more SoC-specific drivers these days.  Some are for
  other driver subsystems where we have received acks from the
  appropriate maintainers.

  The larger parts of this branch are:

   - MediaTek support for their PMIC wrapper interface, a high-level
     interface for talking to the system PMIC over a dedicated I2C
     interface.

   - Qualcomm SCM driver has been moved to drivers/firmware.  It's used
     for CPU up/down and needs to be in a shared location for arm/arm64
     common code.

   - cleanup of ARM-CCI PMU code.

   - another set of cleanusp to the OMAP GPMC code"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
  soc/mediatek: Remove unused variables
  clocksource: atmel-st: select MFD_SYSCON
  soc: mediatek: Add PMIC wrapper for MT8135 and MT8173 SoCs
  arm-cci: Fix CCI PMU event validation
  arm-cci: Split the code for PMU vs driver support
  arm-cci: Get rid of secure transactions for PMU driver
  arm-cci: Abstract the CCI400 PMU specific definitions
  arm-cci: Rearrange code for splitting PMU vs driver code
  drivers: cci: reject groups spanning multiple HW PMUs
  ARM: at91: remove useless include
  clocksource: atmel-st: remove mach/hardware dependency
  clocksource: atmel-st: use syscon/regmap
  ARM: at91: time: move the system timer driver to drivers/clocksource
  ARM: at91: properly initialize timer
  ARM: at91: at91rm9200: remove deprecated arm_pm_restart
  watchdog: at91rm9200: implement restart handler
  watchdog: at91rm9200: use the system timer syscon
  mfd: syscon: Add atmel system timer registers definition
  ARM: at91/dt: declare atmel,at91rm9200-st as a syscon
  soc: qcom: gsbi: Add support for ADM CRCI muxing
  ...

Pull ARM SoC platform updates from Olof Johansson:
 "Our SoC branch usually contains expanded support for new SoCs and
  other core platform code.  In this case, that includes:

   - support for the new Annapurna Labs "Alpine" platform

   - a rework greatly simplifying adding new platform support to the
     MCPM subsystem (Multi-cluster power management)

   - cpuidle and PM improvements for Exynos3250

   - misc updates for Renesas, OMAP, Meson, i.MX.  Some of these could
     have gone in other branches but ended up here for various reasons"

* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (53 commits)
  ARM: alpine: add support for generic pci
  ARM: Exynos: migrate DCSCB to the new MCPM backend abstraction
  ARM: vexpress: migrate DCSCB to the new MCPM backend abstraction
  ARM: vexpress: DCSCB: tighten CPU validity assertion
  ARM: vexpress: migrate TC2 to the new MCPM backend abstraction
  ARM: MCPM: move the algorithmic complexity to the core code
  ARM: EXYNOS: allow cpuidle driver usage on Exynos3250 SoC
  ARM: EXYNOS: add AFTR mode support for Exynos3250
  ARM: EXYNOS: add code for setting/clearing boot flag
  ARM: EXYNOS: fix CPU1 hotplug on Exynos3250
  ARM: S3C64XX: Use fixed IRQ bases to avoid conflicts on Cragganmore
  ARM: cygnus: fix const declaration bcm_cygnus_dt_compat
  ARM: DRA7: hwmod: Fix the hwmod class for GPTimer4
  ARM: DRA7: hwmod: Add data for GPTimers 13 through 16
  ARM: EXYNOS: Remove left over 'extra_save'
  ARM: EXYNOS: Constify exynos_pm_data array
  ARM: EXYNOS: use static in suspend.c
  ARM: EXYNOS: Use platform device name as power domain name
  ARM: EXYNOS: add support for async-bridge clocks for pm_domains
  ARM: omap-device: add missed callback for suspend-to-disk
  ...

Pull ARM SoC fixes from Olof Johansson:
 "Here's the usual "low-priority fixes that didn't make it into the last
  few -rcs, with a twist: We had a fixes pull request that I didn't send
  in time to get into 4.0, so we'll send some of them to Greg for
  -stable as well.

  Contents here is as usual not all that controversial:

   - a handful of randconfig fixes from Arnd, in particular for older
     Samsung platforms

   - Exynos fixes, !SMP building, DTS updates for MMC and lid switch

   - Kbuild fix to create output subdirectory for DTB files

   - misc minor fixes for OMAP"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
  ARM: at91/dt: sama5d3 xplained: add phy address for macb1
  kbuild: Create directory for target DTB
  ARM: mvebu: Disable CPU Idle on Armada 38x
  ARM: DRA7: Enable Cortex A15 errata 798181
  ARM: dts: am57xx-beagle-x15: Add thermal map to include fan and tmp102
  ARM: dts: DRA7: Add bandgap and related thermal nodes
  bus: ocp2scp: SYNC2 value should be changed to 0x6
  ARM: dts: am4372: Add "ti,am437x-ocp2scp" as compatible string for OCP2SCP
  ARM: OMAP2+: remove superfluous NULL pointer check
  ARM: EXYNOS: Fix build breakage cpuidle on !SMP
  ARM: dts: fix lid and power pin-functions for exynos5250-spring
  ARM: dts: fix mmc node updates for exynos5250-spring
  ARM: OMAP4: remove dead kconfig option OMAP4_ERRATA_I688
  MAINTAINERS: add OMAP defconfigs under OMAP SUPPORT
  ARM: OMAP1: PM: fix some build warnings on 1510-only Kconfigs
  ARM: cns3xxx: don't export static symbol
  ARM: S3C24XX: avoid a Kconfig warning
  ARM: S3C24XX: fix header file inclusions
  ARM: S3C24XX: fix building without PM_SLEEP
  ARM: S3C24XX: use SAMSUNG_WAKEMASK for s3c2416
  ...

Pull MIPS updates from Ralf Baechle:
 "This is the main pull request for MIPS for Linux 4.1.  Most
  noteworthy:

   - Add more Octeon-optimized crypto functions
   - Octeon crypto preemption and locking fixes
   - Little endian support for Octeon
   - Use correct CSR to soft reset Octeons
   - Support LEDs on the Octeon-based DSR-1000N
   - Fix PCI interrupt mapping for the Octeon-based DSR-1000N
   - Mark prom_free_prom_memory() as __init for a number of systems
   - Support for Imagination's Pistachio SOC.  This includes arch and
     CLK bits.  I'd like to merge pinctrl bits later
   - Improve parallelism of csum_partial for certain pipelines
   - Organize DTB files in subdirs like other architectures
   - Implement read_sched_clock for all MIPS platforms other than
     Octeon
   - Massive series of 38 fixes and cleanups for the FPU emulator /
     kernel
   - Further FPU remulator work to support new features.  This sits on a
     separate branch which also has been pulled into the 4.1 KVM branch
   - Clean up and fixes for the SEAD3 eval board; remove unused file
   - Various updates for Netlogic platforms
   - A number of small updates for Loongson 3 platforms
   - Increase the memory limit for ATH79 platforms to 256MB
   - A fair number of fixes and updates for BCM47xx platforms
   - Finish the implementation of XPA support
   - MIPS FDC support.  No, not floppy controller but Fast Debug Channel :)
   - Detect the R16000 used in SGI legacy platforms
   - Fix Kconfig dependencies for the SSB bus support"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (265 commits)
  MIPS: Makefile: Fix MIPS ASE detection code
  MIPS: asm: elf: Set O32 default FPU flags
  MIPS: BCM47XX: Fix detecting Microsoft MN-700 & Asus WL500G
  MIPS: Kconfig: Disable SMP/CPS for 64-bit
  MIPS: Hibernate: flush TLB entries earlier
  MIPS: smp-cps: cpu_set FPU mask if FPU present
  MIPS: lose_fpu(): Disable FPU when MSA enabled
  MIPS: ralink: add missing symbol for RALINK_ILL_ACC
  MIPS: ralink: Fix bad config symbol in PCI makefile.
  SSB: fix Kconfig dependencies
  MIPS: Malta: Detect and fix bad memsize values
  Revert "MIPS: Avoid pipeline stalls on some MIPS32R2 cores."
  MIPS: Octeon: Delete override of cpu_has_mips_r2_exec_hazard.
  MIPS: Fix cpu_has_mips_r2_exec_hazard.
  MIPS: kernel: entry.S: Set correct ISA level for mips_ihb
  MIPS: asm: spinlock: Fix addiu instruction for R10000_LLSC_WAR case
  MIPS: r4kcache: Use correct base register for MIPS R6 cache flushes
  MIPS: Kconfig: Fix typo for the r2-to-r6 emulator kernel parameter
  MIPS: unaligned: Fix regular load/store instruction emulation for EVA
  MIPS: unaligned: Surround load/store macros in do {} while statements
  ...

Merge "arm-cci PMU updates for 4.1" from Will Deacon:

CCI-400 PMU updates

This series reworks some of the CCI-400 PMU code so that it can be used
on both ARM and ARM64-based systems, without the need to boot in secure
mode on the latter. This paves the way for CCI-500 support in future.

* tag 'arm-perf-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/will/linux:
  arm-cci: Fix CCI PMU event validation
  arm-cci: Split the code for PMU vs driver support
  arm-cci: Get rid of secure transactions for PMU driver
  arm-cci: Abstract the CCI400 PMU specific definitions
  arm-cci: Rearrange code for splitting PMU vs driver code
  drivers: cci: reject groups spanning multiple HW PMUs
  + Linux 4.0-rc4

Signed-off-by: Olof Johansson <olof@lixom.net>

Add MIPS Common Device Memory Map (CDMM) support in the form of a bus in
the standard Linux device model. Each device attached via CDMM is
discoverable via an 8-bit type identifier and may contain a number of
blocks of memory mapped registers in the CDMM region. IRQs are expected
to be handled separately.

Due to the per-cpu (per-VPE for MT cores) nature of the CDMM devices,
all the driver callbacks take place from workqueues which are run on the
right CPU for the device in question, so that the driver doesn't need to
be as concerned about which CPU it is running on. Callbacks also exist
for when CPUs are taken offline, so that any per-CPU resources used by
the driver can be disabled so they don't get forcefully migrated. CDMM
devices are created as children of the CPU device they are attached to.

Any existing CDMM configuration by the bootloader will be inherited,
however platforms wishing to enable CDMM should implement the weak
mips_cdmm_phys_base() function (see asm/cdmm.h) so that the bus driver
knows where it should put the CDMM region in the physical address space
if the bootloader hasn't already enabled it.

A mips_cdmm_early_probe() function is also provided to allow early boot
or particularly low level code to set up the CDMM region and probe for a
specific device type, for example early console or KGDB IO drivers for
the EJTAG Fast Debug Channel (FDC) CDMM device.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9599/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>