Pull libata changes from Tejun Heo:
 "Nothing too interesting.  Only two minor fixes in libata core.  Most
  changes are specific to hardware which isn't too common"

* 'for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  ahci: Add Device IDs for Intel Wildcat Point-LP
  sata_rcar: Convert to clk_prepare/unprepare
  drivers/libata: Set max sector to 65535 for Slimtype DVD A DS8A9SH drive
  libata: Add some missing command descriptions
  sata_highbank: clear whole array in highbank_initialize_phys()
  ahci: disabled FBS prior to issuing software reset
  libata: Fix display of sata speed
  ahci: imx: setup power saving methods
  ata_piix: minor typo and a printk fix
  ahci: Changing two module params with static and __read_mostly

Tested with Marvell 88se9125, attached with one port mulitplier(5 ports)
and one disk, we will get following boot log messages if using current
code:

  ata8: SATA link up 6.0 Gbps (SStatus 133 SControl 330)
  ata8.15: Port Multiplier 1.2, 0x1b4b:0x9715 r160, 5 ports, feat 0x1/0x1f
  ahci 0000:03:00.0: FBS is enabled
  ata8.00: hard resetting link
  ata8.00: SATA link down (SStatus 0 SControl 330)
  ata8.01: hard resetting link
  ata8.01: SATA link down (SStatus 0 SControl 330)
  ata8.02: hard resetting link
  ata8.02: SATA link down (SStatus 0 SControl 330)
  ata8.03: hard resetting link
  ata8.03: SATA link up 6.0 Gbps (SStatus 133 SControl 133)
  ata8.04: hard resetting link
  ata8.04: failed to resume link (SControl 133)
  ata8.04: failed to read SCR 0 (Emask=0x40)
  ata8.04: failed to read SCR 0 (Emask=0x40)
  ata8.04: failed to read SCR 1 (Emask=0x40)
  ata8.04: failed to read SCR 0 (Emask=0x40)
  ata8.03: native sectors (2) is smaller than sectors (976773168)
  ata8.03: ATA-8: ST3500413AS, JC4B, max UDMA/133
  ata8.03: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
  ata8.03: configured for UDMA/133
  ata8.04: failed to IDENTIFY (I/O error, err_mask=0x100)
  ata8.15: hard resetting link
  ata8.15: SATA link up 6.0 Gbps (SStatus 133 SControl 330)
  ata8.15: Port Multiplier vendor mismatch '0x1b4b' != '0x133'
  ata8.15: PMP revalidation failed (errno=-19)
  ata8.15: hard resetting link
  ata8.15: SATA link up 6.0 Gbps (SStatus 133 SControl 330)
  ata8.15: Port Multiplier vendor mismatch '0x1b4b' != '0x133'
  ata8.15: PMP revalidation failed (errno=-19)
  ata8.15: limiting SATA link speed to 3.0 Gbps
  ata8.15: hard resetting link
  ata8.15: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
  ata8.15: Port Multiplier vendor mismatch '0x1b4b' != '0x133'
  ata8.15: PMP revalidation failed (errno=-19)
  ata8.15: failed to recover PMP after 5 tries, giving up
  ata8.15: Port Multiplier detaching
  ata8.03: disabled
  ata8.00: disabled
  ata8: EH complete

The reason is that current detection code doesn't follow AHCI spec:

First,the port multiplier detection process look like this:

	ahci_hardreset(link, class, deadline)
	if (class == ATA_DEV_PMP) {
		sata_pmp_attach(dev)	/* will enable FBS */
		sata_pmp_init_links(ap, nr_ports);
		ata_for_each_link(link, ap, EDGE) {
			sata_std_hardreset(link, class, deadline);
			if (link_is_online)	/* do soft reset */
				ahci_softreset(link, class, deadline);
		}
	}
But, according to chapter 9.3.9 in AHCI spec: Prior to issuing software
reset, software shall clear PxCMD.ST to '0' and then clear PxFBS.EN to
'0'.

The patch test ok with kernel 3.11.1.

tj: Patch white space contaminated, applied manually with trivial
    updates.

Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org

If EM Transmit bit is busy during init ata_msleep() is called.  It is
wrong - msleep() should be used instead of ata_msleep(), because if EM
Transmit bit is busy for one port, it will be busy for all other ports
too, so using ata_msleep() causes wasting tries for another ports.

The most common scenario looks like that now
(six ports try to transmit a LED meaasege):
- port #0 tries for the 1st time and succeeds
- ports #1-5 try for the 1st time and sleeps
- port #1 tries for the 2nd time and succeeds
- ports #2-5 try for the 2nd time and sleeps
- port #2 tries for the 3rd time and succeeds
- ports #3-5 try for the 3rd time and sleeps
- port #3 tries for the 4th time and succeeds
- ports #4-5 try for the 4th time and sleeps
- port #4 tries for the 5th time and succeeds
- port #5 tries for the 5th time and sleeps

At this moment port #5 wasted all its five tries and failed to
initialize.  Because there are only 5 (EM_MAX_RETRY) tries available
usually only five ports succeed to initialize. The sixth port and next
ones usually will fail.

If msleep() is used instead of ata_msleep() the first port succeeds to
initialize in the first try and next ones usually succeed to
initialize in the second try.

tj: updated comment

Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>

In order to save power consumption as much as possible.

* Disable sata phy internal pll reference clock when sysetem enter
  into suspend mode, enable it after resume.

* Setup module parameter used to enable imx ahci test power down
  mode(PDDQ) or not, when there is no device detected on the port

* minor modifications:
  - The format of the copyright is changed, because that the original
    one can't pass fsl internal patch reivew without the character
    '(c)'.
  - Exports ahci_platform_ops and ahci_error_handler().

NOTE:
* The hot-plug can't be supported when PDDQ mode is ever enabled.

* module parameter usage how-to:
  - default: enable PDDQ mode when no device detected.
  - add "ahci-imx.hotplug=1" into kernel command line if your don't
    want to enable PDDQ mode when no device detected on the port.

tj: Slightly updated description and comments.

Signed-off-by: Richard Zhu <r65037@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>

Here module parameters ahci_em_messages and devslp_idle_timeout can
be set as static and __read_mostly.

Signed-off-by: Liu, Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>

libata/for-3.10-fixes never got submitted during v3.10 cycle.  Merge
it into for-3.11 so that it can be routed together with other changes
scheduled for v3.11.

Three trivial conflicts in drivers/ata/sata_rcar.c.  All are caused by
1b20f6a9ad ("sata_rcar: add 'base' local variable to some functions")
conflicting with logic updates in for-3.10-fixes.  The offending
commit simply adds local variable @base on functions which
dereferences sata_rcar_priv->base multiple times.  The resolutions are
trivial - applying s/priv->base/base/ in the conflicting logic
updates.

Signed-off-by: Tejun Heo <tj@kernel.org>

ahci_hardreset() and ahci_p5wdh_hardreset() use bare numbers for the
BSY bit of the ATA status register, despite it's #define'd in
<linux/ata.h>.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>

ata_link_online() check in ahci_error_intr() is unnecessary, it should
be removed otherwise may lead to lockup with FBS enabled PMP.
http://marc.info/?l=linux-ide&m=137050421603272&w=2

Reported-by: Yu Liu <liuyu.ac@gmail.com>
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org

Create a new ata_port_operations function pointer called
transmit_led_message and give it the default value of
ahci_transmit_led_message. This allows AHCI controllers with
non-standard LED interfaces to use the existing em_ interface.

Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>

Currently all interrupts assigned to AHCI ports show up in
'/proc/interrupts' as 'ahci'. This fix adds port numbers as
suffixes and hence makes the descriptions distinct.

Reported-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>