Signed-off-by: Jeff Garzik <jeff@garzik.org>

Lots of work needed to bring it up to scratch but it does work so you can
now use the card. That makes it at least useful, especially as the other
cardbus cards are usually INIC162x which aren't yet supported well.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This driver nicely wraps around pata_platform library functions,
and provides OF platform bus bindings to the PATA devices.

Also add || PPC to the PATA_PLATFORM's "depends on" Kconfig entry,
needed for PA Semi Electra.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

This patch adds support for Freescale 3.0Gbps SATA Controller supporting
Native Command Queueing(NCQ), device hotplug, and ATAPI.  This controller
can be found on MPC8315 and MPC8378.

Signed-off-by: Ashish Kalra <ashish.kalra@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This is a driver for the ATA controller on the Geode CS5536 companion
chip.  The PCI device ID for this device was previously claimed by
pata_amd.c but the PIO timings were not correct.  This driver also
works around a bug in some BIOSes that handle unaligned access to the
PCI config registers poorly.  Finally, the driver allows fallback to
using MSR registers for configuration on BIOSes that are truly
broken.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

	On a cable there may be
	eighty wires or perhaps forty
	and we learn about its type
	In the world of ACPI

	So we call the GTM
	And we find the the timing rate
	And we look through it to see
	If eighty wire it must be

	Timing lives in ACPI routines
	ACPI routines, ACPI routines
	Timing lives in ACPI routines
	ACPI routes ACPI routines

	And the drivers last you see
	Picking up unknown pci ids
	and the code begins to work

	Timing lives in ACPI routines
	ACPI routines, ACPI routines
	Timing lives in ACPI routines
	ACPI routes ACPI routines

	[Full speed ahead, Mr Hacker, full speed ahead]
	 Full speed over here sir!
	 Checking Cable, checking cable
	 Aye aye, 80 wire,
	 Heaven heaven]

	If we use ACPI (ACPI)
	Every box (every box) has all we need (has all we need)
	Cable type (cable type) and mode timing (mode timing)
	In our ATA (in our ATA) subroutines (subroutines, ha ha)

	Timing lives in ACPI routines
	ACPI routines, ACPI routines
	Timing lives in ACPI routines
	ACPI routes ACPI routines
	Timing lives in ACPI routines
	ACPI routines, ACPI routines
	Timing lives in ACPI routines
	ACPI routes ACPI routines

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Implement Port Multiplier support.  To support PMP, a LLDD has to
supply ops->pmp_read() and pmp_write().  If non-null, ->pmp_attach and
->pmp_detach are called on PMP attach and detach, respectively.

->pmp_read/write() can be called while the port is frozen, so they
must be implemented by polling.  This patch supplies several helpers
to ease ->pmp_read/write() implementation.

Also, irq_handler and error_handler must be PMP aware.  Most of PMP
aware EH can be done by calling ata_pmp_do_eh() with appropriate
methods.  PMP EH uses separate set of reset methods and this patch
implements standard prereset, hardreset and postreset methods.

This patch only implements PMP support.  The next patch will integrate
PMP into the reset of libata and thus enable PMP support.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Alan Cox <alan@redhat.com>
[plus SuperIO fixes by Kyle McMartin]
[plus a cleanup from me]
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Updated and simplified driver. Use only register transfer timing for both
data and register transfers. This gives poorer performance in PIO1 and 2,
but should not be a problem in PIO3 and 4, correct me if I'm wrong :)

The driver works very we'll but I still wonder about the interrupts. I have
an interrupt line, that works nicely when POLLING flag is not set. The
problem is the number of interrupts that eat away my CPU cycles.

When using the POLLING flag there seem to be some interrupts that dosen't get
cleared. Furthermore the device dosen't drive INTRQ high, it stays at 2.5 volts
and generates a lot of interrupts due to ripple / noise. What to do?

Signed-off-by: Kristoffer Nyborg Gregertsen <kngregertsen@norway.atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>