linux.git/drivers/acpi, branch v4.0-rc2

Merge tag 'pm+acpi-3.20-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

2015-02-21T21:40:41+00:00

Pull one more batch of power management and ACPI updates from Rafael Wysocki:
 "These are mostly fixes on top of the previously merged recent PM and
  ACPI material.

  First, one commit that broke the ACPI LPSS (Low-Power Subsystem)
  driver on a Dell box is reverted and there are two stable-candidate
  fixes for that driver.  Another fix cleans up two recently added ACPI
  EC messages that look odd and the printk level of a noisy debug
  message in the core ACPI resources handling code is reduced.

  In addition to that we have two stable-candidate fixes for the s3c
  cpufreq driver, two cpuidle powernv driver updates related to Device
  Trees and a PNP subsystem cleanup that will allow us to get rid of
  some old ugliness going forward.  Also there is a new blacklist entry
  for the ACPI backlight code.

  Specifics:

   - Revert a recent ACPI LPSS driver commit that prevented the touchpad
     driver from loading on Dell XPS13 (Jarkko Nikula).

   - Make the ACPI LPSS driver disable the I2C controllers and deassert
     SPI host controllers resets at startup on Intel BayTrail and
     Braswell SoCs in case they have been left in wrong states by the
     platform firmware which then may casuse fatal controller driver
     failures during resume from hibernation (Mika Westerberg).

   - Make two recently added ACPI EC messages look better (Scot Doyle).

   - Reduce the printk level of a recently added debug message related
     to ACPI resources that may become noisy in some cases (Rafael J
     Wysocki).

   - Add a new ACPI backlight blacklist entry for Samsung Series 9
     (900X3C/900X3D/900X3E/900X4C/900X4D) laptops where the native
     backlight interface doesn't work while the ACPI based one does
     (Jens Reyer).

   - Make the PNP sybsystem's core code use __request_region() followed
     by __release_region() instead of __check_region() which then will
     allow us to get rid of the latter as it has no more users (Jakub
     Sitnicki).

   - Fix a build breakage and an issue with two __init functions that
     may be called after initialization in the s3c cpufreq driver (Arnd
     Bergmann).

   - Make the powernv cpuidle driver read target_residency values for
     idle states from a Device Tree (as we have the suitable DT bindings
     for that now) and improve the parsing of the powermgmt DT node in
     that driver (Preeti U Murthy)"

* tag 'pm+acpi-3.20-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpuidle: powernv: Avoid endianness conversions while parsing DT
  cpufreq: s3c: remove last use of resume_clocks callback
  cpufreq: s3c: remove incorrect __init annotations
  ACPI / LPSS: Deassert resets for SPI host controllers on Braswell
  ACPI / LPSS: Always disable I2C host controllers
  ACPI / resources: Change pr_info() to pr_debug() for debug information
  ACPI / video: Disable native backlight on Samsung Series 9 laptops
  cpuidle: powernv: Read target_residency value of idle states from DT if available
  Revert "ACPI / LPSS: Remove non-existing clock control from Intel Lynxpoint I2C"
  ACPI / EC: Remove non-standard log emphasis
  PNP: Switch from __check_region() to __request_region()

Merge branches 'acpi-ec', 'acpi-soc', 'acpi-video' and 'acpi-resources'

2015-02-21T03:28:56+00:00

* acpi-ec:
  ACPI / EC: Remove non-standard log emphasis

* acpi-soc:
  ACPI / LPSS: Deassert resets for SPI host controllers on Braswell
  ACPI / LPSS: Always disable I2C host controllers
  Revert "ACPI / LPSS: Remove non-existing clock control from Intel Lynxpoint I2C"

* acpi-video:
  ACPI / video: Disable native backlight on Samsung Series 9 laptops

* acpi-resources:
  ACPI / resources: Change pr_info() to pr_debug() for debug information

Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux

2015-02-19T19:28:36+00:00

Pull thermal managament updates from Zhang Rui:
 "Specifics:

   - Abstract the code and introduce helper functions for all int340x
     thermal drivers.  From: Srinivas Pandruvada.

   - Reorganize the ACPI LPAT table support code so that it can be
     shared for both ACPI PMIC driver and int340x thermal driver.

   - Add support for Braswell in intel_soc_dts thermal driver.

   - a couple of small fixes/cleanups for step_wise governor and int340x
     thermal driver"

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  Thermal/int340x_thermal: remove unused uuids.
  thermal: step_wise: spelling fixes
  thermal: int340x: fix sparse warning
  Thermal/int340x: LPAT conversion for temperature
  ACPI / PMIC: Use common LPAT table handling functions
  ACPI / LPAT: Common table processing functions
  thermal: Intel SoC DTS: Add Braswell support
  Thermal/int340x/int3402: Provide notification support
  Thermal/int340x/processor_thermal: Add thermal zone support
  Thermal/int340x/int3403: Use int340x thermal API
  Thermal/int340x/int3402: Use int340x thermal API
  Thermal/int340x: Add common thermal zone handler

ACPI / LPSS: Deassert resets for SPI host controllers on Braswell

2015-02-18T17:47:44+00:00

On some Braswell systems BIOS leaves resets for SPI host controllers
active. This prevents the SPI driver from transferring messages on wire.

Fix this in similar way that we do for I2C already by deasserting resets
for the SPI host controllers.

Reported-by: Yang A Fang 
Signed-off-by: Mika Westerberg 
Cc: 3.17+  # 3.17+
Signed-off-by: Rafael J. Wysocki

ACPI / LPSS: Always disable I2C host controllers

2015-02-18T17:46:40+00:00

On Baytrail and Braswell the BIOS might leave the I2C host controllers
enabled, probably because it uses them for its own purposes. This is fine
in normal cases because the I2C driver will disable the hardware when it
is probed anyway.

However, in case of suspend to disk it is different story. If the driver
happens to be compiled as a module the boot kernel never loads the driver
thus leaving host controllers enabled upon loading the hibernation image.

The I2C host controller interrupt mask register has default value of 0x8ff,
in other words it has most of the interrupts unmasked. When combined with
the fact that the host controller is enabled, the driver immediately starts
getting interrupts even before its resume hook is called (once IO-APIC is
resumed). Since the driver is not prepared for this it will crash the
kernel due to NULL pointer derefence because dev->msgs is NULL.

Unfortunately we were not able to get full backtrace to from the console
which could be reproduced here.

In order to fix this even when the driver is compiled as module, we disable
the I2C host controllers in byt_i2c_setup() before devices are created.

Reported-by: Yu Chen 
Signed-off-by: Mika Westerberg 
Cc: 3.17+  # 3.17+
Signed-off-by: Rafael J. Wysocki

ACPI / resources: Change pr_info() to pr_debug() for debug information

2015-02-18T07:05:43+00:00

Annoying and noisy ACPI debug messages are printed with pr_info()
after the recent ACPI resources handling rework.  Replace the
pr_info() with pr_debug() to reduce to noise level.

Reported-by: Borislav Petkov 
Signed-off-by: Rafael J. Wysocki

ACPI / video: Disable native backlight on Samsung Series 9 laptops

2015-02-18T05:41:34+00:00

Add video_disable_native_backlight quirk for SAMSUNG 900X3C/900X3D/
900X3E/900X4C/900X4D laptops.

The native intel backlight controls do not work correctly on SAMSUNG
Series 9 (900X3C/900X3D/900X3E/900X4C/900X4D) laptops:
One machine has an completely dimmed (= black) display after boot at the
GDM login screen and brightness controls work only between 0 and 5%
(= no effect).
Another machine has the same brightness control issues if an external
HDMI monitor is or gets connected, although the initial brightness is
ok.
After login to Gnome both machines always work fine.

Tested on both machines.

Link: https://bugs.freedesktop.org/show_bug.cgi?id=87286
Link: https://bugs.debian.org/772440
Signed-off-by: Jens Reyer 
Signed-off-by: Rafael J. Wysocki

Revert "ACPI / LPSS: Remove non-existing clock control from Intel Lynxpoint I2C"

2015-02-17T17:30:48+00:00

Revert commit b893e80e3147 ("ACPI / LPSS: Remove non-existing clock control
from Intel Lynxpoint I2C") because it causes touchpad to not load on Dell
XPS13.

Regression is a clear indication that not only some early prototype version
of Lynxpoint I2C but also newer versions can be doing clock gating even
documentation does not state it.

Therefore it is best to revert since this clock gating haven't caused known
issues on those Lynxpoint version which don't do clock gating.

Reported-by-and-tested-by: Chris Rorvick 
Signed-off-by: Jarkko Nikula 
Signed-off-by: Rafael J. Wysocki

ACPI / EC: Remove non-standard log emphasis

2015-02-17T17:27:59+00:00

Remove unusual pr_info() visual emphasis introduced in ad479e7f47ca
"ACPI / EC: Introduce STARTED/STOPPED flags to replace BLOCKED flag".

Signed-off-by: Scot Doyle 
[ rjw: Change pr_info() to pr_debug() too in those places. ]
Signed-off-by: Rafael J. Wysocki

ACPI / idle: Implement ->enter_freeze callback routine

2015-02-15T18:40:10+00:00

Add an ->enter_freeze callback routine, acpi_idle_enter_freeze(), to
the ACPI cpuidle driver and point ->enter_freeze to it for all the
C2-type and C3-type states that don't need to fall back to C1
(which may be halt-induced and that will re-enable interrupts on
exit from idle, which ->enter_freeze cannot do).

Signed-off-by: Rafael J. Wysocki 
Acked-by: Peter Zijlstra (Intel)