linux.git/drivers/acpi/sleep.c, branch v4.20

ACPI / PM: save NVS memory for ASUS 1025C laptop

2018-07-11T09:42:13+00:00

Every time I tried to upgrade my laptop from 3.10.x to 4.x I faced an
issue by which the fan would run at full speed upon resume. Bisecting
it showed me the issue was introduced in 3.17 by commit 821d6f0359b0
(ACPI / sleep: Do not save NVS for new machines to accelerate S3). This
code only affects machines built starting as of 2012, but this Asus
1025C laptop was made in 2012 and apparently needs the NVS data to be
saved, otherwise the CPU's thermal state is not properly reported on
resume and the fan runs at full speed upon resume.

Here's a very simple way to check if such a machine is affected :

  # cat /sys/class/thermal/thermal_zone0/temp
  55000

  ( now suspend, wait one second and resume )

  # cat /sys/class/thermal/thermal_zone0/temp
  0

  (and after ~15 seconds the fan starts to spin)

Let's apply the same quirk as commit cbc00c13 (ACPI: save NVS memory
for Lenovo G50-45) and reuse the function it provides. Note that this
commit was already backported to 4.9.x but not 4.4.x.

Cc: 3.17+  # 3.17+: requires cbc00c13
Signed-off-by: Willy Tarreau 
Signed-off-by: Rafael J. Wysocki

ACPI / PM: Default to s2idle in all machines supporting LP S0

2018-07-04T09:50:13+00:00

The Dell Venue Pro 7140 supports the Low Power S0 Idle state, but
does not support any of the _DSM functions that the current heuristic
checks for.

Since suspend-to-mem can not be safely performed on this machine,
and since the bitfield check can't cover this case, it is safer
to enable s2idle by default by checking for the presence of the
_DSM alone and removing the bitfield check.

Signed-off-by: Tristian Celestin 
Signed-off-by: Rafael J. Wysocki

ACPI: EC: Dispatch the EC GPE directly on s2idle wake

2018-05-25T08:32:13+00:00

On platforms where the Low Power S0 Idle _DSM interface is used,
on wakeup from suspend-to-idle, when it is known that the ACPI SCI
has triggered while suspended, dispatch the EC GPE in order to catch
all EC events that may have triggered the wakeup before carrying out
the noirq phase of device resume.

That is needed to handle power button wakeup on some platforms where
the EC goes into a low-power mode during suspend-to-idle and while in
that mode it will discard events after a timeout.  If that timeout is
shorter than the time it takes to complete the noirq resume of
devices, looking for EC events after the latter is too late.

Signed-off-by: Rafael J. Wysocki 
Reported-by: Zhang Rui 
Tested-by: Wendy Wang

ACPI / PM: Blacklist Low Power S0 Idle _DSM for ThinkPad X1 Tablet(2016)

2018-04-23T06:53:17+00:00

ThinkPad X1 Tablet(2016) is reported to have issues with
the Low Power S0 Idle _DSM interface and since this machine
model generally can do ACPI S3 just fine, and user would
like to use S3 as default sleep model, add a blacklist
entry to disable that interface for ThinkPad X1 Tablet(2016).

Link: https://bugzilla.kernel.org/show_bug.cgi?id=199057
Reported-and-tested-by: Robin Lee 
Signed-off-by: Chen Yu 
Signed-off-by: Rafael J. Wysocki

Merge tag 'pm-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

2018-04-03T17:45:39+00:00

Pull power management updates from Rafael Wysocki:
 "These update the cpuidle poll state definition to reduce excessive
  energy usage related to it, add new CPU ID to the RAPL power capping
  driver, update the ACPI system suspend code to handle some special
  cases better, extend the PM core's device links code slightly, add new
  sysfs attribute for better suspend-to-idle diagnostics and easier
  hibernation handling, update power management tools and clean up
  cpufreq quite a bit.

  Specifics:

   - Modify the cpuidle poll state implementation to prevent CPUs from
     staying in the loop in there for excessive times (Rafael Wysocki).

   - Add Intel Cannon Lake chips support to the RAPL power capping
     driver (Joe Konno).

   - Add reference counting to the device links handling code in the PM
     core (Lukas Wunner).

   - Avoid reconfiguring GPEs on suspend-to-idle in the ACPI system
     suspend code (Rafael Wysocki).

   - Allow devices to be put into deeper low-power states via ACPI if
     both _SxD and _SxW are missing (Daniel Drake).

   - Reorganize the core ACPI suspend-to-idle wakeup code to avoid a
     keyboard wakeup issue on Asus UX331UA (Chris Chiu).

   - Prevent the PCMCIA library code from aborting suspend-to-idle due
     to noirq suspend failures resulting from incorrect assumptions
     (Rafael Wysocki).

   - Add coupled cpuidle supprt to the Exynos3250 platform (Marek
     Szyprowski).

   - Add new sysfs file to make it easier to specify the image storage
     location during hibernation (Mario Limonciello).

   - Add sysfs files for collecting suspend-to-idle usage and time
     statistics for CPU idle states (Rafael Wysocki).

   - Update the pm-graph utilities (Todd Brandt).

   - Reduce the kernel log noise related to reporting Low-power Idle
     constraings by the ACPI system suspend code (Rafael Wysocki).

   - Make it easier to distinguish dedicated wakeup IRQs in the
     /proc/interrupts output (Tony Lindgren).

   - Add the frequency table validation in cpufreq to the core and drop
     it from a number of cpufreq drivers (Viresh Kumar).

   - Drop "cooling-{min|max}-level" for CPU nodes from a couple of DT
     bindings (Viresh Kumar).

   - Clean up the CPU online error code path in the cpufreq core (Viresh
     Kumar).

   - Fix assorted issues in the SCPI, CPPC, mediatek and tegra186
     cpufreq drivers (Arnd Bergmann, Chunyu Hu, George Cherian, Viresh
     Kumar).

   - Drop memory allocation error messages from a few places in cpufreq
     and cpuildle drivers (Markus Elfring)"

* tag 'pm-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (56 commits)
  ACPI / PM: Fix keyboard wakeup from suspend-to-idle on ASUS UX331UA
  cpufreq: CPPC: Use transition_delay_us depending transition_latency
  PM / hibernate: Change message when writing to /sys/power/resume
  PM / hibernate: Make passing hibernate offsets more friendly
  cpuidle: poll_state: Avoid invoking local_clock() too often
  PM: cpuidle/suspend: Add s2idle usage and time state attributes
  cpuidle: Enable coupled cpuidle support on Exynos3250 platform
  cpuidle: poll_state: Add time limit to poll_idle()
  cpufreq: tegra186: Don't validate the frequency table twice
  cpufreq: speedstep: Don't validate the frequency table twice
  cpufreq: sparc: Don't validate the frequency table twice
  cpufreq: sh: Don't validate the frequency table twice
  cpufreq: sfi: Don't validate the frequency table twice
  cpufreq: scpi: Don't validate the frequency table twice
  cpufreq: sc520: Don't validate the frequency table twice
  cpufreq: s3c24xx: Don't validate the frequency table twice
  cpufreq: qoirq: Don't validate the frequency table twice
  cpufreq: pxa: Don't validate the frequency table twice
  cpufreq: ppc_cbe: Don't validate the frequency table twice
  cpufreq: powernow: Don't validate the frequency table twice
  ...

ACPI / PM: Fix keyboard wakeup from suspend-to-idle on ASUS UX331UA

2018-03-31T09:00:55+00:00

This issue happens on new ASUS laptop UX331UA which has modern
standby mode (suspend-to-idle). Pressing keys on the PS2 keyboard
can't wake up the system from suspend-to-idle which is not expected.
However, pressing power button can wake up without problem.

Per the engineers of ASUS, the keypress event is routed to Embedded
Controller (EC) in standby mode. EC then signals the SCI event to
BIOS so BIOS would Notify() power button to wake up the system. It's
from BIOS perspective. What we observe here is that kernel receives
the SCI event from SCI interrupt handler which informs that the GPE
status bit belongs to EC needs to be handled and then queries the EC
to find out what event is pending. Then execute the following ACPI
_QDF method which defined in ACPI DSDT for EC to notify power button.

 Method (_QDF, 0, NotSerialized)  // _Qxx: EC Query
        {
            Notify (PWRB, 0x80) // Status Change
        }

With more debug messages added to analyze this problem, we find that
the keypress does wake up the system from suspend-to-idle but it's back
to suspend again almost immediately. As we see in the following messages,
the acpi_button_notify() is invoked but acpi_pm_wakeup_event() can not
really wake up the system here because acpi_s2idle_wakeup() is false.
The acpi_s2idle_wakeup() returnd false because the acpi_s2idle_sync() has
alrealdy exited.

[   52.987048] s2idle_loop going s2idle
[   59.713392] acpi_s2idle_wake enter
[   59.713394] acpi_s2idle_wake exit
[   59.760888] acpi_ev_gpe_detect enter
[   59.760893] acpi_s2idle_sync enter
[   59.760893] acpi_ec_query_flushed ec pending queries 0
[   59.760953] Read registers for GPE 50-57: Status=01, Enable=01, RunEnable=01, WakeEnable=00
[   59.760955] ACPI: EC: ===== IRQ (1) =====
[   59.760972] ACPI: EC: EC_SC(R) = 0x28 SCI_EVT=1 BURST=0 CMD=1 IBF=0 OBF=0
[   59.760979] ACPI: EC: +++++ Polling enabled +++++
[   59.760979] ACPI: EC: ##### Command(QR_EC) submitted/blocked #####
[   59.761003] acpi_s2idle_sync exit
[   59.769587] ACPI: EC: ##### Query(0xdf) started #####
[   59.769611] ACPI: EC: ##### Query(0xdf) stopped #####
[   59.774154] acpi_button_notify button type 1
[   59.813175] s2idle_loop going s2idle

acpi_s2idle_sync() already makes an effort to flush the EC event
queue, but in this case, the EC event has yet to be generated when
the call to acpi_ec_flush_work() is made. The event is generated
shortly after, through the ongoing handling of the SCI interrupt
which is happening on another CPU, and we must synchronize that
to make sure that it has run and completed. Adding another call to
acpi_os_wait_events_complete() solves this issue, since that
function synchronizes with SCI interrupt completion.

Signed-off-by: Chris Chiu 
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki

ACPI / PM: Reduce LPI constraints logging noise

2018-03-18T22:55:01+00:00

If a device referred to by ACPI LPI constrains (coming from function 1
of the Low Power S0 Idle _DSM interface) is not power-manageable via
ACPI (no _PS0 method and no power resources), the code generating
diagnostic information for the LPI constraints will print a message
about that to the kernel log on every system suspend-resume cycle
(possibly for multiple times).

That is not very useful and noisy, so modify that code to disregard
the LPI list entries corresponding to the devices that are not power-
manageable after printing that information for them once.

Signed-off-by: Rafael J. Wysocki 
Reviewed-by: Srinivas Pandruvada

ACPI/sleep: Simplify code by using the new dmi_get_bios_year() helper

2018-02-23T07:20:30+00:00

...instead of open coding its functionality.

No changes in functionality.

Signed-off-by: Andy Shevchenko 
Cc: Bjorn Helgaas 
Cc: Jean Delvare 
Cc: Linus Torvalds 
Cc: Peter Zijlstra 
Cc: Rafael J. Wysocki 
Cc: Thomas Gleixner 
Cc: linux-acpi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/20180222125923.57385-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Ingo Molnar

ACPI / PM: Do not reconfigure GPEs for suspend-to-idle

2018-02-21T22:53:34+00:00

It is reported that commit 235d81a630ca (ACPI / PM: Clean up device
wakeup enable/disable code) broke wakeup from suspend-to-idle on
some platforms.  That is due to the acpi_enable_all_wakeup_gpes() in
acpi_s2idle_prepare() which needs acpi_enable_wakeup_devices() to be
called before it as the latter sets up the GPE masks used by the
former and commit 235d81a630ca removed acpi_enable_wakeup_devices()
invocation from the suspend-to-idle path.

However, acpi_enable_wakeup_devices() does more than just setting
the GPE masks and the remaining part of it is not necessary for
suspend-to-idle.  Moreover, non-wakeup GPEs are disabled on suspend-
to-idle entry to avoid spurious wakeups, but that should not be
strictly necessary any more after commit 33e4f80ee69b (ACPI / PM:
Ignore spurious SCI wakeups from suspend-to-idle) which prevents
spurious GPE wakeups from resuming the system.  The only consequence
of leaving non-wakeup GPEs enabled may be more interrupt-related
activity while suspended, which is not ideal (more energy is used
if that happens), but it is not critical too.

For this reason, drop the GPE reconfiguration from the suspend-to-idle
path entirely.

This change also allows Dells XPS13 9360 blacklisted by commit
71630b7a832f (ACPI / PM: Blacklist Low Power S0 Idle _DSM for Dell
XPS13 9360) to use the power button for waking up from suspend-
to-idle and it helps at least one other older Dell system (the
wakeup button GPE on that one is not listed in _PRW for any
devices, so it is not regarded as a wakeup one and gets disabled
on suspend-to-idle entry today).

Fixes: 235d81a630ca (ACPI / PM: Clean up device wakeup enable/disable code)
Reported-by: Du Wenkai 
Tested-by: Du Wenkai 
Signed-off-by: Rafael J. Wysocki

ACPI / PM: Use Low Power S0 Idle on more systems

2018-01-11T17:54:31+00:00

Some systems don't support the ACPI_LPS0_ENTRY and ACPI_LPS0_EXIT
functions in their Low Power S0 Idle _DSM, but still expect EC
events to be processed in the suspend-to-idle state for power button
wakeup (among other things) to work.  Surface Pro3 turns out to be
one of them.

Fortunately, it still provides Low Power S0 Idle _DSM with the screen
on/off functions supported, so modify the ACPI suspend-to-idle to use
the Low Power S0 Idle code path for all systems supporting the
ACPI_LPS0_ENTRY and ACPI_LPS0_EXIT or the ACPI_LPS0_SCREEN_OFF and
ACPI_LPS0_SCREEN_ON functions in their Low Power S0 Idle _DSM.

Potentially, that will cause more systems to use suspend-to-idle by
default, so some future corrections may be necessary if it leads
to issues, but let it remain more straightforward for now.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=198389#add_comment
Reported-by: Valentin Manea 
Signed-off-by: Rafael J. Wysocki 
Reviewed-by: Andy Shevchenko 
Tested-by: Valentin Manea