linux.git/drivers/acpi/scan.c, branch v5.8

Merge tag 'pm-5.8-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

2020-06-10T21:04:39+00:00

Pull more power management updates from Rafael Wysocki:
 "These are operating performance points (OPP) framework updates mostly,
  including support for interconnect bandwidth in the OPP core, plus a
  few cpufreq changes, including boost support in the CPPC cpufreq
  driver, an ACPI device power management fix and a hibernation code
  cleanup.

  Specifics:

   - Add support for interconnect bandwidth to the OPP core (Georgi
     Djakov, Saravana Kannan, Sibi Sankar, Viresh Kumar).

   - Add support for regulator enable/disable to the OPP core (Kamil
     Konieczny).

   - Add boost support to the CPPC cpufreq driver (Xiongfeng Wang).

   - Make the tegra186 cpufreq driver set the
     CPUFREQ_NEED_INITIAL_FREQ_CHECK flag (Mian Yousaf Kaukab).

   - Prevent the ACPI power management from using power resources with
     devices where the list of power resources for power state D0 (full
     power) is missing (Rafael Wysocki).

   - Annotate a hibernation-related function with __init (Christophe
     JAILLET)"

* tag 'pm-5.8-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: PM: Avoid using power resources if there are none for D0
  cpufreq: CPPC: add SW BOOST support
  cpufreq: change '.set_boost' to act on one policy
  PM: hibernate: Add __init annotation to swsusp_header_init()
  opp: Don't parse icc paths unnecessarily
  opp: Remove bandwidth votes when target_freq is zero
  opp: core: add regulators enable and disable
  opp: Reorder the code for !target_freq case
  opp: Expose bandwidth information via debugfs
  cpufreq: dt: Add support for interconnect bandwidth scaling
  opp: Update the bandwidth on OPP frequency changes
  opp: Add sanity checks in _read_opp_key()
  opp: Add support for parsing interconnect bandwidth
  cpufreq: tegra186: add CPUFREQ_NEED_INITIAL_FREQ_CHECK flag
  OPP: Add helpers for reading the binding properties
  dt-bindings: opp: Introduce opp-peak-kBps and opp-avg-kBps bindings

mm: reorder includes after introduction of linux/pgtable.h

2020-06-09T16:39:13+00:00

The replacement of  with  made the include
of the latter in the middle of asm includes.  Fix this up with the aid of
the below script and manual adjustments here and there.

	import sys
	import re

	if len(sys.argv) is not 3:
	    print "USAGE: %s  " % (sys.argv[0])
	    sys.exit(1)

	hdr_to_move="#include " % sys.argv[2]
	moved = False
	in_hdrs = False

	with open(sys.argv[1], "r") as f:
	    lines = f.readlines()
	    for _line in lines:
		line = _line.rstrip('
')
		if line == hdr_to_move:
		    continue
		if line.startswith("#include 
Signed-off-by: Andrew Morton 
Cc: Arnd Bergmann 
Cc: Borislav Petkov 
Cc: Brian Cain 
Cc: Catalin Marinas 
Cc: Chris Zankel 
Cc: "David S. Miller" 
Cc: Geert Uytterhoeven 
Cc: Greentime Hu 
Cc: Greg Ungerer 
Cc: Guan Xuetao 
Cc: Guo Ren 
Cc: Heiko Carstens 
Cc: Helge Deller 
Cc: Ingo Molnar 
Cc: Ley Foon Tan 
Cc: Mark Salter 
Cc: Matthew Wilcox 
Cc: Matt Turner 
Cc: Max Filippov 
Cc: Michael Ellerman 
Cc: Michal Simek 
Cc: Nick Hu 
Cc: Paul Walmsley 
Cc: Richard Weinberger 
Cc: Rich Felker 
Cc: Russell King 
Cc: Stafford Horne 
Cc: Thomas Bogendoerfer 
Cc: Thomas Gleixner 
Cc: Tony Luck 
Cc: Vincent Chen 
Cc: Vineet Gupta 
Cc: Will Deacon 
Cc: Yoshinori Sato 
Link: http://lkml.kernel.org/r/20200514170327.31389-4-rppt@kernel.org
Signed-off-by: Linus Torvalds

mm: introduce include/linux/pgtable.h

2020-06-09T16:39:13+00:00

The include/linux/pgtable.h is going to be the home of generic page table
manipulation functions.

Start with moving asm-generic/pgtable.h to include/linux/pgtable.h and
make the latter include asm/pgtable.h.

Signed-off-by: Mike Rapoport 
Signed-off-by: Andrew Morton 
Cc: Arnd Bergmann 
Cc: Borislav Petkov 
Cc: Brian Cain 
Cc: Catalin Marinas 
Cc: Chris Zankel 
Cc: "David S. Miller" 
Cc: Geert Uytterhoeven 
Cc: Greentime Hu 
Cc: Greg Ungerer 
Cc: Guan Xuetao 
Cc: Guo Ren 
Cc: Heiko Carstens 
Cc: Helge Deller 
Cc: Ingo Molnar 
Cc: Ley Foon Tan 
Cc: Mark Salter 
Cc: Matthew Wilcox 
Cc: Matt Turner 
Cc: Max Filippov 
Cc: Michael Ellerman 
Cc: Michal Simek 
Cc: Nick Hu 
Cc: Paul Walmsley 
Cc: Richard Weinberger 
Cc: Rich Felker 
Cc: Russell King 
Cc: Stafford Horne 
Cc: Thomas Bogendoerfer 
Cc: Thomas Gleixner 
Cc: Tony Luck 
Cc: Vincent Chen 
Cc: Vineet Gupta 
Cc: Will Deacon 
Cc: Yoshinori Sato 
Link: http://lkml.kernel.org/r/20200514170327.31389-3-rppt@kernel.org
Signed-off-by: Linus Torvalds

ACPI: PM: Avoid using power resources if there are none for D0

2020-06-08T11:31:24+00:00

As recently reported, some platforms provide a list of power
resources for device power state D3hot, through the _PR3 object,
but they do not provide a list of power resources for device power
state D0.

Among other things, this causes acpi_device_get_power() to return
D3hot as the current state of the device in question if all of the
D3hot power resources are "on", because it sees the power_resources
flag set and calls acpi_power_get_inferred_state() which finds that
D3hot is the shallowest power state with all of the associated power
resources turned "on", so that's what it returns.  Moreover, that
value takes precedence over the acpi_dev_pm_explicit_get() return
value, because it means a deeper power state.  The device may very
well be in D0 physically at that point, however.

Moreover, the presence of _PR3 without _PR0 for a given device
means that only one D3-level power state can be supported by it.
Namely, because there are no power resources to turn "off" when
transitioning the device from D0 into D3cold (which should be
supported since _PR3 is present), the evaluation of _PS3 should
be sufficient to put it straight into D3cold, but this means that
the effect of turning "on" the _PR3 power resources is unclear,
so it is better to avoid doing that altogether.  Consequently,
there is no practical way do distinguish D3cold from D3hot for
the device in question and the power states of it can be labeled
so that D3hot is the deepest supported one (and Linux assumes
that putting a device into D3hot via ACPI may cause power to be
removed from it anyway, for legacy reasons).

To work around the problem described above modify the ACPI
enumeration of devices so that power resources are only used
for device power management if the list of D0 power resources
is not empty and make it mart D3cold as supported only if that
is the case and the D3hot list of power resources is not empty
too.

Fixes: ef85bdbec444 ("ACPI / scan: Consolidate extraction of power resources lists")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205057
Link: https://lore.kernel.org/linux-acpi/20200603194659.185757-1-hdegoede@redhat.com/
Reported-by: Hans de Goede 
Tested-by: Hans de Goede 
Tested-by: youling257@gmail.com
Cc: 3.10+  # 3.10+
Signed-off-by: Rafael J. Wysocki 
Reviewed-by: Hans de Goede

ACPI: scan: Put SPCR and STAO table after using it

2020-05-09T09:29:17+00:00

The SPCR and STAO table needs to be released after
using it.

Signed-off-by: Hanjun Guo 
Signed-off-by: Rafael J. Wysocki

treewide: remove redundant IS_ERR() before error code check

2020-02-04T03:05:27+00:00

'PTR_ERR(p) == -E*' is a stronger condition than IS_ERR(p).
Hence, IS_ERR(p) is unneeded.

The semantic patch that generates this commit is as follows:

// 
@@
expression ptr;
constant error_code;
@@
-IS_ERR(ptr) && (PTR_ERR(ptr) == - error_code)
+PTR_ERR(ptr) == - error_code
// 

Link: http://lkml.kernel.org/r/20200106045833.1725-1-masahiroy@kernel.org
Signed-off-by: Masahiro Yamada 
Cc: Julia Lawall 
Acked-by: Stephen Boyd  [drivers/clk/clk.c]
Acked-by: Bartosz Golaszewski  [GPIO]
Acked-by: Wolfram Sang  [drivers/i2c]
Acked-by: Rafael J. Wysocki  [acpi/scan.c]
Acked-by: Rob Herring 
Cc: Eric Biggers 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

ACPI: platform: Unregister stale platform devices

2019-10-17T21:48:39+00:00

When commit 68bdb6773289 ("ACPI: add support for ACPI reconfiguration
notifiers") introduced reconfiguration notifiers, it missed the point
that the ACPI table, which might be loaded and then unloaded via
ConfigFS, could contain devices that were not enumerated by their
parents.

In such cases, the stale platform device is dangling in the system
while the rest of the devices from the same table are already gone.

Introduce acpi_platform_device_remove_notify() notifier that, in
similar way to I²C or SPI buses, unregisters the platform devices
on table removal event.

Fixes: 68bdb6773289 ("ACPI: add support for ACPI reconfiguration notifiers")
Depends-on: 00500147cbd3 ("drivers: Introduce device lookup variants by ACPI_COMPANION device")
Signed-off-by: Andy Shevchenko 
[ rjw: Changelog & function rename ]
Signed-off-by: Rafael J. Wysocki

drivers/acpi/scan.c: document why we don't need the device_hotplug_lock

2019-08-03T14:02:01+00:00

Let's document why the lock is not needed in acpi_scan_init(), right now
this is not really obvious.

[akpm@linux-foundation.org: fix tpyo]
Link: http://lkml.kernel.org/r/20190731135306.31524-1-david@redhat.com
Signed-off-by: David Hildenbrand 
Acked-by: Michal Hocko 
Acked-by: Rafael J. Wysocki 
Cc: Oscar Salvador 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

treewide: Add SPDX license identifier for missed files

2019-05-21T08:50:45+00:00

Add SPDX license identifiers to all files which:

 - Have no license information of any form

 - Have EXPORT_.*_SYMBOL_GPL inside which was used in the
   initial scan/conversion to ignore the file

These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:

  GPL-2.0-only

Signed-off-by: Thomas Gleixner 
Signed-off-by: Greg Kroah-Hartman

Merge tag 'driver-core-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

2019-05-07T20:01:40+00:00

Pull driver core/kobject updates from Greg KH:
 "Here is the "big" set of driver core patches for 5.2-rc1

  There are a number of ACPI patches in here as well, as Rafael said
  they should go through this tree due to the driver core changes they
  required. They have all been acked by the ACPI developers.

  There are also a number of small subsystem-specific changes in here,
  due to some changes to the kobject core code. Those too have all been
  acked by the various subsystem maintainers.

  As for content, it's pretty boring outside of the ACPI changes:
   - spdx cleanups
   - kobject documentation updates
   - default attribute groups for kobjects
   - other minor kobject/driver core fixes

  All have been in linux-next for a while with no reported issues"

* tag 'driver-core-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (47 commits)
  kobject: clean up the kobject add documentation a bit more
  kobject: Fix kernel-doc comment first line
  kobject: Remove docstring reference to kset
  firmware_loader: Fix a typo ("syfs" -> "sysfs")
  kobject: fix dereference before null check on kobj
  Revert "driver core: platform: Fix the usage of platform device name(pdev->name)"
  init/config: Do not select BUILD_BIN2C for IKCONFIG
  Provide in-kernel headers to make extending kernel easier
  kobject: Improve doc clarity kobject_init_and_add()
  kobject: Improve docs for kobject_add/del
  driver core: platform: Fix the usage of platform device name(pdev->name)
  livepatch: Replace klp_ktype_patch's default_attrs with groups
  cpufreq: schedutil: Replace default_attrs field with groups
  padata: Replace padata_attr_type default_attrs field with groups
  irqdesc: Replace irq_kobj_type's default_attrs field with groups
  net-sysfs: Replace ktype default_attrs field with groups
  block: Replace all ktype default_attrs with groups
  samples/kobject: Replace foo_ktype's default_attrs field with groups
  kobject: Add support for default attribute groups to kobj_type
  driver core: Postpone DMA tear-down until after devres release for probe failure
  ...