The FPU usage related to task FPU management is either protected by
disabling interrupts (switch_to, return to user) or via fpregs_lock() which
is a wrapper around local_bh_disable(). When kernel code wants to use the
FPU then it has to check whether it is possible by calling irq_fpu_usable().

But the condition in irq_fpu_usable() is wrong. It allows FPU to be used
when:

   !in_interrupt() || interrupted_user_mode() || interrupted_kernel_fpu_idle()

The latter is checking whether some other context already uses FPU in the
kernel, but if that's not the case then it allows FPU to be used
unconditionally even if the calling context interrupted a fpregs_lock()
critical region. If that happens then the FPU state of the interrupted
context becomes corrupted.

Allow in kernel FPU usage only when no other context has in kernel FPU
usage and either the calling context is not hard interrupt context or the
hard interrupt did not interrupt a local bottomhalf disabled region.

It's hard to find a proper Fixes tag as the condition was broken in one way
or the other for a very long time and the eager/lazy FPU changes caused a
lot of churn. Picked something remotely connected from the history.

This survived undetected for quite some time as FPU usage in interrupt
context is rare, but the recent changes to the random code unearthed it at
least on a kernel which had FPU debugging enabled. There is probably a
higher rate of silent corruption as not all issues can be detected by the
FPU debugging code. This will be addressed in a subsequent change.

Fixes: 5d2bd7009f30 ("x86, fpu: decouple non-lazy/eager fpu restore from xsave")
Reported-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220501193102.588689270@linutronix.de

Use the offset calculation to do the size calculation which avoids yet
another series of CPUID instructions for each invocation.

  [ Fix the FP/SSE only case which missed to take the xstate
    header into account, as
    Reported-by: kernel test robot <oliver.sang@intel.com> ]

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/87o81pgbp2.ffs@tglx

The size calculation in __xstate_request_perm() fails to take supervisor
states into account because the permission bitmap is only relevant for user
states.

Up to 5.17 this does not matter because there are no supervisor states
supported, but the (re-)enabling of ENQCMD makes them available.

Fixes: 7c1ef59145f1 ("x86/cpufeatures: Re-enable ENQCMD")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220324134623.681768598@linutronix.de

So far the cached fixed compacted offsets worked, but with (re-)enabling
of ENQCMD this does no longer work with KVM fpstate.

KVM does not have supervisor features enabled for the guest FPU, which
means that KVM has then a different XSAVE area layout than the host FPU
state. This in turn breaks the copy from/to UABI functions when invoked for
a guest state.

Remove the pre-calculated compacted offsets and calculate the offset
of each component at runtime based on the XCOMP_BV field in the XSAVE
header.

The runtime overhead is not interesting because these copy from/to UABI
functions are not used in critical fast paths. KVM uses them to save and
restore FPU state during migration. The host uses them for ptrace and for
the slow path of 32bit signal handling.

Fixes: 7c1ef59145f1 ("x86/cpufeatures: Re-enable ENQCMD")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220324134623.627636809@linutronix.de

In preparation for runtime calculation of XSAVE offsets cache the feature
flags for each XSTATE component during feature enumeration via CPUID(0xD).

EDX has two relevant bits:
    0	Supervisor component
    1	Feature storage must be 64 byte aligned

These bits are currently only evaluated during init, but the alignment bit
must be cached to make runtime calculation of XSAVE offsets efficient.

Cache the full EDX content and use it for the existing alignment and
supervisor checks.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220324134623.573656209@linutronix.de

Reading XSTATE feature information from CPUID over and over does not make
sense. The information has to be cached anyway, so it can be done early.

Prepare for runtime calculation of XSTATE offsets and allow
consolidation of the size calculation functions in a later step.

Rename the function while at it as it does not setup any features.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220324134623.519411939@linutronix.de

No users.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220324134623.465066249@linutronix.de

fpu_copy_uabi_to_guest_fpstate() initializes the XCOMP_BV field in the
XSAVE header. That's a leftover from the old KVM FPU buffer handling code.

Since

  d69c1382e1b7 ("x86/kvm: Convert FPU handling to a single swap buffer")

KVM uses the FPU core allocation code, which initializes the XCOMP_BV
field already.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220324134623.408932232@linutronix.de

ARCH_REQ_XCOMP_PERM is supposed to add the requested feature to the
permission bitmap of thread_group_leader()->fpu. But the code overwrites
the bitmap with the requested feature bit only rather than adding it.

Fix the code to add the requested feature bit to the master bitmask.

Fixes: db8268df0983 ("x86/arch_prctl: Add controls for dynamic XSTATE components")
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Paolo Bonzini <bonzini@gnu.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220129173647.27981-2-chang.seok.bae@intel.com

Pull x86 PASID support from Thomas Gleixner:
 "Reenable ENQCMD/PASID support:

   - Simplify the PASID handling to allocate the PASID once, associate
     it to the mm of a process and free it on mm_exit().

     The previous attempt of refcounted PASIDs and dynamic
     alloc()/free() turned out to be error prone and too complex. The
     PASID space is 20bits, so the case of resource exhaustion is a pure
     academic concern.

   - Populate the PASID MSR on demand via #GP to avoid racy updates via
     IPIs.

   - Reenable ENQCMD and let objtool check for the forbidden usage of
     ENQCMD in the kernel.

   - Update the documentation for Shared Virtual Addressing accordingly"

* tag 'x86-pasid-2022-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  Documentation/x86: Update documentation for SVA (Shared Virtual Addressing)
  tools/objtool: Check for use of the ENQCMD instruction in the kernel
  x86/cpufeatures: Re-enable ENQCMD
  x86/traps: Demand-populate PASID MSR via #GP
  sched: Define and initialize a flag to identify valid PASID in the task
  x86/fpu: Clear PASID when copying fpstate
  iommu/sva: Assign a PASID to mm on PASID allocation and free it on mm exit
  kernel/fork: Initialize mm's PASID
  iommu/ioasid: Introduce a helper to check for valid PASIDs
  mm: Change CONFIG option for mm->pasid field
  iommu/sva: Rename CONFIG_IOMMU_SVA_LIB to CONFIG_IOMMU_SVA