Function 'os_flush_stdout' is declared twice, so remove the
repeated declaration.

Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Richard Weinberger <richard@nod.at>

1. Reflect host cpu flags into the UML instance so they can
be used to select the correct implementations for xor, crypto, etc.

2. Reflect host cache alignment into UML instance. This is
important when running 32 bit on a 64 bit host as 32 bit by
default aligns to 32 while the actual alignment should be 64.
Ditto for some Xeons which align at 128.

Signed-off-by: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Signed-off-by: Richard Weinberger <richard@nod.at>

We should be able to ndelay() from any context, even from an
interrupt context! However, this is broken (not functionally,
but locking-wise) in time-travel because we'll get into the
time-travel code and enable interrupts to handle messages on
other time-travel aware subsystems (only virtio for now).

Luckily, I've already reworked the time-travel aware signal
(interrupt) delivery for suspend/resume to have a time travel
handler, which runs directly in the context of the signal and
not from the Linux interrupt.

In order to fix this time-travel issue then, we need to do a
few things:

 1) rework the signal handling code to call time-travel handlers
    (only) if interrupts are disabled but signals aren't blocked,
    instead of marking it only pending there. This is needed to
    not deadlock other communication.
 2) rework time-travel to not enable interrupts while it's
    waiting for a message;
 3) rework time-travel to not (just) disable interrupts but
    rather block signals at a lower level while it needs them
    disabled for communicating with the controller.

Finally, since now we can actually spend even virtual time
in interrupts-disabled sections, the delay warning when we
deliver a time-travel delayed interrupt is no longer valid,
things can (and should) now get delayed.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>

This will be necessary in the userspace side to fix the
signal/interrupt handling in time-travel=ext mode, which
is the next patch.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>

Use signals_enabled instead of always jumping through
a function call to read it, there's not much point in
that.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>

This function doesn't exist, remove its declaration.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Signed-off-by: Richard Weinberger <richard@nod.at>

This mostly reverts the old commit 3963333fe676 ("uml: cover stubs
with a VMA") which had added a VMA to the existing PTEs. However,
there's no real reason to have the PTEs in the first place and the
VMA cannot be 'fixed' in place, which leads to bugs that userspace
could try to unmap them and be forcefully killed, or such. Also,
there's a bit of an ugly hole in userspace's address space.

Simplify all this: just install the stub code/page at the top of
the (inner) address space, i.e. put it just above TASK_SIZE. The
pages are simply hard-coded to be mapped in the userspace process
we use to implement an mm context, and they're out of reach of the
inner mmap/munmap/mprotect etc. since they're above TASK_SIZE.

Getting rid of the VMA also makes vma_merge() no longer hit one of
the VM_WARN_ON()s there because we installed a VMA while the code
assumes the stack VMA is the first one.

It also removes a lockdep warning about mmap_sem usage since we no
longer have uml_setup_stubs() and thus no longer need to do any
manipulation that would require mmap_sem in activate_mm().

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>

The userspace stacks mostly have a stack (and in the case of the
syscall stub we can just set their stack pointer) that points to
the location of the stub data page already.

Rework the stubs to use the stack pointer to derive the start of
the data page, rather than requiring it to be hard-coded.

In the clone stub, also integrate the int3 into the stack remap,
since we really must not use the stack while we remap it.

This prepares for putting the stub at a variable location that's
not part of the normal address space of the userspace processes
running inside the UML machine.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>

If the two are mixed up, then it looks as though the parent
returned an error if the child failed (before) the mmap(),
and then the resulting process never gets killed. Fix this
by splitting the child and parent errors, reporting and
using them appropriately.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>

In some cases we can get to fix_range_common() with mmap_sem held,
and in others we get there without it being held. For example, we
get there with it held from sys_mprotect(), and without it held
from fork_handler().

Avoid any issues in this and simply defer killing the task until
it runs the next time. Do it on the mm so that another task that
shares the same mm can't continue running afterwards.

Cc: stable@vger.kernel.org
Fixes: 468f65976a8d ("um: Fix hung task in fix_range_common()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>