linux.git/arch/sh/kernel/cpu/init.c, branch v4.19

Replace with globally

2016-12-24T19:46:01+00:00

This was entirely automated, using the script by Al:

  PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*'
  sed -i -e "s!$PATT!#include !" \
        $(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)

to do the replacement at the end of the merge window.

Requested-by: Al Viro 
Signed-off-by: Linus Torvalds

sh: add support for J-Core J2 processor

2016-08-05T03:29:31+00:00

At the CPU/ISA level, the J2 is compatible with SH-2, and thus the
changes to add J2 support build on existing SH-2 support. However, J2
does not duplicate the memory-mapped SH-2 features like the cache
interface. Instead, the cache interfaces is described in the device
tree, and new code is added to be able to access the flat device tree
at early boot before it is unflattened.

Support is also added for receiving interrupts on trap numbers in the
range 16 to 31, since the J-Core aic1 interrupt controller generates
these traps. This range was unused but nominally for hardware
exceptions on SH-2, and a few values in this range were used for
exceptions on SH-2A, but SH-2A has its own version of the relevant
code.

No individual cpu subtypes are added for J2 since the intent moving
forward is to represent SoCs with device tree rather than as
hard-coded subtypes in the kernel. The CPU_SUBTYPE_J2 Kconfig item
exists only to fit into the existing cpu selection mechanism until it
is overhauled.

Signed-off-by: Rich Felker

sh: disable aliased page logic on NOMMU models

2016-07-31T03:33:32+00:00

SH3/4 (with MMU) have a virtually indexed cache, requiring explicit
work to avoid consistency problems arising from having the same
physical address range cached in multiple cache lines. This is
unneeded for the NOMMU case, and some of the resulting code paths
(kmap_coherent) don't work. SH2 only avoided this problem by having a
4-way associative cache with way size equal to the page size (4k),
yielding no cache index bits outside of the page offset and thus no
aliases.

Signed-off-by: Rich Felker

sh: prefix sh-specific "CCR" and "CCR2" by "SH_"

2014-03-04T15:55:49+00:00

Commit bcf24e1daa94 ("mmc: omap_hsmmc: use the generic config for
omap2plus devices"), enabled the build for other platforms for compile
testing.

sh-allmodconfig now fails with:

    include/linux/omap-dma.h:171:8: error: expected identifier before numeric constant
    make[4]: *** [drivers/mmc/host/omap_hsmmc.o] Error 1

This happens because SuperH #defines "CCR", which is one of the enum
values in include/linux/omap-dma.h.  There's a similar issue with "CCR2"
on sh2a.

As "CCR" and "CCR2" are too generic names for global #defines, prefix
them with "SH_" to fix this.

Signed-off-by: Geert Uytterhoeven 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

sh: delete __cpuinit usage from all sh files

2013-07-14T23:36:53+00:00

The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications.  For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.

After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out.  Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.

Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit  -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings.  In any case, they are temporary and harmless.

This removes all the arch/sh uses of the __cpuinit macros from
all C files.  Currently sh does not have any __CPUINIT used in
assembly files.

[1] https://lkml.org/lkml/2013/5/20/589

Cc: Paul Mundt 
Cc: linux-sh@vger.kernel.org
Signed-off-by: Paul Gortmaker

Disintegrate asm/system.h for SH

2012-03-28T17:30:03+00:00

Disintegrate asm/system.h for SH.

Signed-off-by: David Howells 
cc: linux-sh@vger.kernel.org

sh: Expose physical addressing mode through cpuinfo.

2010-10-26T05:44:58+00:00

CPUs can be in either the legacy 29-bit or 32-bit physical addressing
modes. This follows the x86 approach of tracking the phys bits in cpuinfo
and exposing it to userspace through procfs.

This change was requested to permit kexec-tools to detect the physical
addressing mode in order to determine the appropriate address mangling.

Signed-off-by: Paul Mundt

sh: __cpuinit annotate the CPU init path.

2010-04-21T03:20:42+00:00

All of the regular CPU init path needs to be __cpuinit annotated for CPU
hotplug.

Signed-off-by: Paul Mundt

sh: Tidy CPU probing and fixup section annotations.

2010-04-21T03:01:06+00:00

This does a detect_cpu_and_cache_system() -> cpu_probe() rename, tidies
up the unused return value, and stuffs it under __cpuinit in preparation
for CPU hotplug.

Signed-off-by: Paul Mundt

sh: Setup boot CPU VBR early to enable early page faults.

2010-02-17T03:33:22+00:00

vmemmap and the vmsplit code amongst others need to be able to take page
faults much earlier than trap_init() time, so move this in to the early
CPU initialization. VBR setup for secondary CPUs is already handled
through start_secondary(), so we only need to do this for the boot CPU.

Signed-off-by: Paul Mundt