RISC-V Devicetree fixes for v6.10-rc5+

T-Head:
Jisheng hasn't got enough time to look after the platform, so Drew
Fustini is going to take over.

StarFive:
A fix for a regulator voltage range that prevented using low performance
SD cards.

Canaan:
Cleanup for some "over eager" aliases for serial ports that did not
exist on some boards and I/O devices disabled on boards where they were
not actually in use.

Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Currently, for JH7110 boards with EMMC slot, vqmmc voltage for EMMC is
fixed to 1.8V, while the spec needs it to be 3.3V on low speed mode and
should support switching to 1.8V when using higher speed mode. Since
there are no other peripherals using the same voltage source of EMMC's
vqmmc(ALDO4) on every board currently supported by mainline kernel,
regulator-max-microvolt of ALDO4 should be set to 3.3V.

Cc: stable@vger.kernel.org
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Fixes: 7dafcfa79cc9 ("riscv: dts: starfive: enable DCDC1&ALDO4 node in axp15060")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>

Milkv Duo does not have a write-protect pin, so disable write protect
to prevent SDcards misdetected as read-only.

Fixes: 89a7056ed4f7 ("riscv: dts: sophgo: add sdcard support for milkv duo")
Signed-off-by: Haylen Chu <heylenay@outlook.com>
Link: https://lore.kernel.org/r/SEYPR01MB4221943C7B101DD2318DA0D3D7CE2@SEYPR01MB4221.apcprd01.prod.exchangelabs.com
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>

It is considered good practice to disable on-SoC devices providing
external I/O in the SoC-specific .dtsi, and enable them explicitly in
the board-specific DTS files when actually wired-up and used.

Hence:
  - Set the status of I/O devices in k210.dtsi to "disabled",
  - Override the status of used I/O devices in board-specific DTS files
    to "okay",
  - Drop unneeded status overrides in board DTS-specific files for the
    always-enabled pin controller.

On e.g. MAiXBiT, this gets rid of an error message when probing the
unused slave-only spi2 controller:

    dw_spi_mmio 50240000.spi: error -22: problem registering spi host
    dw_spi_mmio 50240000.spi: probe with driver dw_spi_mmio failed with error -22

which is seen since commit 98d75b9ef282f6b9 ("spi: dw: Drop default
number of CS setting").

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>

The SoC-specific k210.dtsi declares aliases for all four serial ports.
However, none of the board-specific DTS files configure pin control for
any but the first serial port, so the last three ports are not usable.

Move the aliases node from the SoC-specific k210.dtsi to the
board-specific DTS files, as these are really board-specific, and retain
the sole port that is usable.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>

Previously the build process would always set KBUILD_IMAGE to the
uncompressed Image file (unless XIP_KERNEL or EFI_ZBOOT was enabled) and
unconditionally compress it into Image.gz. However there are already
build targets for Image.bz2, Image.lz4, Image.lzma, Image.lzo and
Image.zstd, so let's make use of those, make the compression method
configurable and set KBUILD_IMAGE accordingly so that targets like
'make install' and 'make bindeb-pkg' will use the chosen image.

Tested-by: Björn Töpel <bjorn@rivosinc.com>
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Nicolas Schier <n.schier@avm.de>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20240504193446.196886-2-emil.renner.berthing@canonical.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>

Pull more SoC devicetree updates from Arnd Bergmann:
 "This is a follow-up to an earlier pull request for device tree
  changes, as three platform maintainers sent their contents too late to
  be included in the main set, but had not caused any further problems
  since then:

   - The Amlogic platform now containts support for two new SoC types,
     the A4 and A5 chips for audio applications. Both come with a
     reference board, and one more dts file gets addded for the
     combination of the MNT Reform Laptop with the BPI-CM4 CPU module

   - The ASpeed platform adds support for six addititional server
     platforms that use ast2500 or ast2600 as their BMC, while another
     one gets removed

   - The RISC-V platforms from Microchip, Starfive and and T-HEAD get
     additional features for existing hardware, plus the addition of the
     Milk-V Mars based on the StarFive VisionFive v2 board"

* tag 'soc-dt-late-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (76 commits)
  riscv: dts: microchip: add pac1934 power-monitor to icicle
  riscv: dts: thead: Fix node ordering in TH1520 device tree
  ARM: dts: aspeed: Add ASRock E3C256D4I BMC
  dt-bindings: arm: aspeed: document ASRock E3C256D4I
  dt-bindings: trivial-devices: add isil,isl69269
  ARM: dts: aspeed: x4tf: Add dts for asus x4tf project
  dt-bindings: arm: aspeed: add ASUS X4TF board
  ARM: dts: aspeed: Remove Facebook Cloudripper dts
  ARM: dts: aspeed: drop unused ref_voltage ADC property
  ARM: dts: aspeed: harma: correct Mellanox multi-host property
  ARM: dts: aspeed: yosemitev2: correct Mellanox multi-host property
  ARM: dts: aspeed: yosemite4: correct Mellanox multi-host property
  ARM: dts: aspeed: greatlakes: correct Mellanox multi-host property
  ARM: dts: aspeed: Modify I2C bus configuration
  ARM: dts: aspeed: Disable unused ADC channels for Asrock X570D4U BMC
  ARM: dts: aspeed: Modify GPIO table for Asrock X570D4U BMC
  ARM: dts: aspeed: yosemite4: set bus13 frequency to 100k
  ARM: dts: Aspeed: Bonnell: Fix NVMe LED labels
  ARM: dts: aspeed: yosemite4: Enable ipmb device for OCP debug card
  ARM: dts: aspeed: ahe50dc: Update lm25066 regulator name
  ...

Pull Kbuild updates from Masahiro Yamada:

 - Avoid 'constexpr', which is a keyword in C23

 - Allow 'dtbs_check' and 'dt_compatible_check' run independently of
   'dt_binding_check'

 - Fix weak references to avoid GOT entries in position-independent code
   generation

 - Convert the last use of 'optional' property in arch/sh/Kconfig

 - Remove support for the 'optional' property in Kconfig

 - Remove support for Clang's ThinLTO caching, which does not work with
   the .incbin directive

 - Change the semantics of $(src) so it always points to the source
   directory, which fixes Makefile inconsistencies between upstream and
   downstream

 - Fix 'make tar-pkg' for RISC-V to produce a consistent package

 - Provide reasonable default coverage for objtool, sanitizers, and
   profilers

 - Remove redundant OBJECT_FILES_NON_STANDARD, KASAN_SANITIZE, etc.

 - Remove the last use of tristate choice in drivers/rapidio/Kconfig

 - Various cleanups and fixes in Kconfig

* tag 'kbuild-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (46 commits)
  kconfig: use sym_get_choice_menu() in sym_check_prop()
  rapidio: remove choice for enumeration
  kconfig: lxdialog: remove initialization with A_NORMAL
  kconfig: m/nconf: merge two item_add_str() calls
  kconfig: m/nconf: remove dead code to display value of bool choice
  kconfig: m/nconf: remove dead code to display children of choice members
  kconfig: gconf: show checkbox for choice correctly
  kbuild: use GCOV_PROFILE and KCSAN_SANITIZE in scripts/Makefile.modfinal
  Makefile: remove redundant tool coverage variables
  kbuild: provide reasonable defaults for tool coverage
  modules: Drop the .export_symbol section from the final modules
  kconfig: use menu_list_for_each_sym() in sym_check_choice_deps()
  kconfig: use sym_get_choice_menu() in conf_write_defconfig()
  kconfig: add sym_get_choice_menu() helper
  kconfig: turn defaults and additional prompt for choice members into error
  kconfig: turn missing prompt for choice members into error
  kconfig: turn conf_choice() into void function
  kconfig: use linked list in sym_set_changed()
  kconfig: gconf: use MENU_CHANGED instead of SYMBOL_CHANGED
  kconfig: gconf: remove debug code
  ...

Now Kbuild provides reasonable defaults for objtool, sanitizers, and
profilers.

Remove redundant variables.

Note:

This commit changes the coverage for some objects:

  - include arch/mips/vdso/vdso-image.o into UBSAN, GCOV, KCOV
  - include arch/sparc/vdso/vdso-image-*.o into UBSAN
  - include arch/sparc/vdso/vma.o into UBSAN
  - include arch/x86/entry/vdso/extable.o into KASAN, KCSAN, UBSAN, GCOV, KCOV
  - include arch/x86/entry/vdso/vdso-image-*.o into KASAN, KCSAN, UBSAN, GCOV, KCOV
  - include arch/x86/entry/vdso/vdso32-setup.o into KASAN, KCSAN, UBSAN, GCOV, KCOV
  - include arch/x86/entry/vdso/vma.o into GCOV, KCOV
  - include arch/x86/um/vdso/vma.o into KASAN, GCOV, KCOV

I believe these are positive effects because all of them are kernel
space objects.

Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Roberto Sassu <roberto.sassu@huawei.com>

The binding for this landed in v6.9, add the description. In the
off-chance that there were people carrying local patches for this based
on the driver shipped on the Microchip website (or vendor kernel) both
the binding and sysfs filenames changed during upstreaming.

Signed-off-by: Conor Dooley <conor.dooley@microchip.com>