Commit 67d96729a9e7 ("riscv: Update Canaan Kendryte K210 device tree")
incorrectly removed two entries from the PLIC interrupt-controller node's
interrupts-extended property.

The PLIC driver cannot know the mapping between hart contexts and hart ids,
so this information has to be provided by device tree, as specified by the
PLIC device tree binding.

The PLIC driver uses the interrupts-extended property, and initializes the
hart context registers in the exact same order as provided by the
interrupts-extended property.

In other words, if we don't specify the S-mode interrupts, the PLIC driver
will simply initialize the hart0 S-mode hart context with the hart1 M-mode
configuration. It is therefore essential to specify the S-mode IRQs even
though the system itself will only ever be running in M-mode.

Re-add the S-mode interrupts, so that we get working IRQs on hart1 again.

Cc: <stable@vger.kernel.org>
Fixes: 67d96729a9e7 ("riscv: Update Canaan Kendryte K210 device tree")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>

Some of the GPIO pins on the Unmatched are wire up to control the power
of the board, indicate that in the device tree.

Signed-off-by: Ron Economos <w6rz@comcast.net>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>

Pull RISC-V updates from Palmer Dabbelt:

 - Support for the DA9063 as used on the HiFive Unmatched.

 - Support for relative extables, which puts us in line with other
   architectures and save some space in vmlinux.

 - A handful of kexec fixes/improvements, including the ability to run
   crash kernels from PCI-addressable memory on the HiFive Unmatched.

 - Support for the SBI SRST extension, which allows systems that do not
   have an explicit driver in Linux to reboot.

 - A handful of fixes and cleanups, including to the defconfigs and
   device trees.

* tag 'riscv-for-linus-5.17-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (52 commits)
  RISC-V: Use SBI SRST extension when available
  riscv: mm: fix wrong phys_ram_base value for RV64
  RISC-V: Use common riscv_cpuid_to_hartid_mask() for both SMP=y and SMP=n
  riscv: head: remove useless __PAGE_ALIGNED_BSS and .balign
  riscv: errata: alternative: mark vendor_patch_func __initdata
  riscv: head: make secondary_start_common() static
  riscv: remove cpu_stop()
  riscv: try to allocate crashkern region from 32bit addressible memory
  riscv: use hart id instead of cpu id on machine_kexec
  riscv: Don't use va_pa_offset on kdump
  riscv: dts: sifive: fu540-c000: Fix PLIC node
  riscv: dts: sifive: fu540-c000: Drop bogus soc node compatible values
  riscv: dts: sifive: Group tuples in register properties
  riscv: dts: sifive: Group tuples in interrupt properties
  riscv: dts: microchip: mpfs: Group tuples in interrupt properties
  riscv: dts: microchip: mpfs: Fix clock controller node
  riscv: dts: microchip: mpfs: Fix reference clock node
  riscv: dts: microchip: mpfs: Fix PLIC node
  riscv: dts: microchip: mpfs: Drop empty chosen node
  riscv: dts: canaan: Group tuples in interrupt properties
  ...

Pull Kbuild updates from Masahiro Yamada:

 - Add new kconfig target 'make mod2noconfig', which will be useful to
   speed up the build and test iteration.

 - Raise the minimum supported version of LLVM to 11.0.0

 - Refactor certs/Makefile

 - Change the format of include/config/auto.conf to stop double-quoting
   string type CONFIG options.

 - Fix ARCH=sh builds in dash

 - Separate compression macros for general purposes (cmd_bzip2 etc.) and
   the ones for decompressors (cmd_bzip2_with_size etc.)

 - Misc Makefile cleanups

* tag 'kbuild-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (34 commits)
  kbuild: add cmd_file_size
  arch: decompressor: remove useless vmlinux.bin.all-y
  kbuild: rename cmd_{bzip2,lzma,lzo,lz4,xzkern,zstd22}
  kbuild: drop $(size_append) from cmd_zstd
  sh: rename suffix-y to suffix_y
  doc: kbuild: fix default in `imply` table
  microblaze: use built-in function to get CPU_{MAJOR,MINOR,REV}
  certs: move scripts/extract-cert to certs/
  kbuild: do not quote string values in include/config/auto.conf
  kbuild: do not include include/config/auto.conf from shell scripts
  certs: simplify $(srctree)/ handling and remove config_filename macro
  kbuild: stop using config_filename in scripts/Makefile.modsign
  certs: remove misleading comments about GCC PR
  certs: refactor file cleaning
  certs: remove unneeded -I$(srctree) option for system_certificates.o
  certs: unify duplicated cmd_extract_certs and improve the log
  certs: use $< and $@ to simplify the key generation rule
  kbuild: remove headers_check stub
  kbuild: move headers_check.pl to usr/include/
  certs: use if_changed to re-generate the key when the key type is changed
  ...

Pull RISC-V SoC updates from Arnd Bergmann:
 "Add support for StarFive JH7100 RISC-V SoC

  This adds support for the StarFive JH7100, including the necessary
  device drivers and DT files for the BeagleV Starlight prototype board,
  with additional boards to be added later. This SoC promises to be the
  first usable low-cost platform for RISC-V.

  I've taken this through the SoC tree in the anticipation of adding a
  few other Arm based SoCs as well, but those did not pass the review in
  time, so it's only this one"

* tag 'newsoc-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  reset: starfive-jh7100: Fix 32bit compilation
  RISC-V: Add BeagleV Starlight Beta device tree
  RISC-V: Add initial StarFive JH7100 device tree
  serial: 8250_dw: Add StarFive JH7100 quirk
  dt-bindings: serial: snps-dw-apb-uart: Add JH7100 uarts
  pinctrl: starfive: Add pinctrl driver for StarFive SoCs
  dt-bindings: pinctrl: Add StarFive JH7100 bindings
  dt-bindings: pinctrl: Add StarFive pinctrl definitions
  reset: starfive-jh7100: Add StarFive JH7100 reset driver
  dt-bindings: reset: Add Starfive JH7100 reset bindings
  dt-bindings: reset: Add StarFive JH7100 reset definitions
  clk: starfive: Add JH7100 clock generator driver
  dt-bindings: clock: starfive: Add JH7100 bindings
  dt-bindings: clock: starfive: Add JH7100 clock definitions
  dt-bindings: interrupt-controller: Add StarFive JH7100 plic
  dt-bindings: timer: Add StarFive JH7100 clint
  RISC-V: Add StarFive SoC Kconfig option

Fix the device node for the Platform-Level Interrupt Controller (PLIC):
  - Add missing "#address-cells" property,
  - Sort properties according to DT bindings.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>

"make dtbs_check":

    arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dt.yaml: soc: $nodename:0: '/' was expected
    	From schema: Documentation/devicetree/bindings/riscv/sifive.yaml
    arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dt.yaml: soc: compatible: 'oneOf' conditional failed, one must be fixed:
    	'sifive,fu540-c000' is not one of ['sifive,hifive-unleashed-a00']
    	'sifive,fu540-c000' is not one of ['sifive,hifive-unmatched-a00']
    	'sifive,fu540-c000' was expected
    	'sifive,fu740-c000' was expected
    	'sifive,fu540' was expected
    	'sifive,fu740' was expected
    	From schema: Documentation/devicetree/bindings/riscv/sifive.yaml

This happens because the "soc" subnode declares compatibility with
"sifive,fu540-c000" and "sifive,fu540", while these are only intended
for the root node.

Fix this by removing the bogus compatible values from the "soc" node.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>

To improve human readability and enable automatic validation, the tuples
in "reg" properties containing register blocks should be grouped using
angle brackets.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>

To improve human readability and enable automatic validation, the tuples
in the various properties containing interrupt specifiers should be
grouped.

Fix this by grouping the tuples of "interrupts" and
"interrupts-extended" properties using angle brackets.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>

To improve human readability and enable automatic validation, the tuples
in the various properties containing interrupt specifiers should be
grouped.

Fix this by grouping the tuples of "interrupts" and
"interrupts-extended" properties using angle brackets.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>