Convert arch/powerpc/ over to long long based u64:

 -#ifdef __powerpc64__
 -# include <asm-generic/int-l64.h>
 -#else
 -# include <asm-generic/int-ll64.h>
 -#endif
 +#include <asm-generic/int-ll64.h>

This will avoid reoccuring spurious warnings in core kernel code that
comes when people test on their own hardware. (i.e. x86 in ~98% of the
cases) This is what x86 uses and it generally helps keep 64-bit code
32-bit clean too.

[Adjusted to not impact user mode (from paulus) - sfr]

Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
  x86: export vector_used_by_percpu_irq
  x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
  sched: nominate preferred wakeup cpu, fix
  x86: fix lguest used_vectors breakage, -v2
  x86: fix warning in arch/x86/kernel/io_apic.c
  sched: fix warning in kernel/sched.c
  sched: move test_sd_parent() to an SMP section of sched.h
  sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
  sched: activate active load balancing in new idle cpus
  sched: bias task wakeups to preferred semi-idle packages
  sched: nominate preferred wakeup cpu
  sched: favour lower logical cpu number for sched_mc balance
  sched: framework for sched_mc/smt_power_savings=N
  sched: convert BALANCE_FOR_xx_POWER to inline functions
  x86: use possible_cpus=NUM to extend the possible cpus allowed
  x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
  x86: update io_apic.c to the new cpumask code
  x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
  x86: xen: use smp_call_function_many()
  x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
  ...

Fixed up trivial conflict in kernel/time/tick-sched.c manually

Impact: change existing irq_chip API

Not much point with gentle transition here: the struct irq_chip's
setaffinity method signature needs to change.

Fortunately, not widely used code, but hits a few architectures.

Note: In irq_select_affinity() I save a temporary in by mangling
irq_desc[irq].affinity directly.  Ingo, does this break anything?

(Folded in fix from KOSAKI Motohiro)

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Acked-by: Ingo Molnar <mingo@redhat.com>
Cc: ralf@linux-mips.org
Cc: grundler@parisc-linux.org
Cc: jeremy@xensource.com
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>

In the CONFIG_SMP case the irq_choose_cpu() code was returning back
a logical cpu id not the physical id.  We were writing that directly
into the HW register.

We need to be calling get_hard_smp_processor_id() so irq_choose_cpu()
always returns a physical cpu id.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Kexec/kdump currently fails on the IBM QS2x blades when the kexec happens
on a CPU other than the initial boot CPU.  It turns out that this is the
result of mpic_init trying to set affinity of each interrupt vector to the
current boot CPU.

As far as I can tell,  the same problem is likely to exist on any
secondary MPIC, because they have to deliver interrupts to the first
output all the time. There are two potential solutions for this: either
not set up affinity at all for secondary MPICs, or assume that a single
CPU output is connected to the upstream interrupt controller and hardcode
affinity to that per architecture.

This patch implements the second approach, defaulting to the first output.
Currently, all known secondary MPICs are routed to their upstream port
using the first destination, so we hardcode that.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>

MPIC has 4 ipis, so it can use the new smp_request_message_ipi to
reduce pathlength when receiving an ipi.

This has the side effect of using the common ipi names, and also
continuing to try request the remaining messages when one fails.

Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The Freescale implementation of MPIC only allows a single CPU destination
for non-IPI interrupts.  We add a flag to the mpic_init to distinquish
these variants of MPIC.  We pull in the irq_choose_cpu from sparc64 to
select a single CPU as the destination of the interrupt.

This is to deal with the fact that the default smp affinity was
changed by commit 18404756765c713a0be4eb1082920c04822ce588 ("genirq:
Expose default irq affinity mask (take 3)") to be all CPUs.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Manual merge of:

	arch/powerpc/Kconfig
	arch/powerpc/kernel/stacktrace.c
	arch/powerpc/mm/slice.c
	arch/ppc/kernel/smp.c

This converts ppc to use the new helpers for smp_call_function() and
friends, and adds support for smp_call_function_single().

ppc loses the timeout functionality of smp_call_function_mask() with
this change, as the generic code does not provide that.

Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>