The X.509 certificates trusted by the platform and required to secure
boot the OS kernel are wrapped in secure variables, which are
controlled by OPAL.

This patch adds firmware/kernel interface to read and write OPAL
secure variables based on the unique key.

This support can be enabled using CONFIG_OPAL_SECVAR.

Signed-off-by: Claudio Carvalho <cclaudio@linux.ibm.com>
Signed-off-by: Nayna Jain <nayna@linux.ibm.com>
Signed-off-by: Eric Richter <erichte@linux.ibm.com>
[mpe: Make secvar_ops __ro_after_init, only build opal-secvar.c if PPC_SECURE_BOOT=y]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1573441836-3632-2-git-send-email-nayna@linux.ibm.com

MPIPL is Memory Preserving IPL supported from POWER9. This enables the
kernel to reset the system with memory 'preserved'. Also, it supports
copying memory from a source address to some destination address during
MPIPL boot. Add MPIPL interface definitions here to leverage these f/w
features in adding FADump support for PowerNV platform.

Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/156821340710.5656.10071829040515662624.stgit@hbathini.in.ibm.com

We have OPAL_MSG_PRD message type to pass prd related messages from
OPAL to `opal-prd`. It can handle messages upto 64 bytes. We have a
requirement to send bigger than 64 bytes of data from OPAL to
`opal-prd`. Lets add new message type (OPAL_MSG_PRD2) to pass bigger
data.

Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
[mpe: Make the error string clear that it's the PRD2 event that failed]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190826065701.8853-2-hegdevasant@linux.vnet.ibm.com

Pull powerpc updates from Michael Ellerman:
 "Notable changes:

   - Removal of the NPU DMA code, used by the out-of-tree Nvidia driver,
     as well as some other functions only used by drivers that haven't
     (yet?) made it upstream.

   - A fix for a bug in our handling of hardware watchpoints (eg. perf
     record -e mem: ...) which could lead to register corruption and
     kernel crashes.

   - Enable HAVE_ARCH_HUGE_VMAP, which allows us to use large pages for
     vmalloc when using the Radix MMU.

   - A large but incremental rewrite of our exception handling code to
     use gas macros rather than multiple levels of nested CPP macros.

  And the usual small fixes, cleanups and improvements.

  Thanks to: Alastair D'Silva, Alexey Kardashevskiy, Andreas Schwab,
  Aneesh Kumar K.V, Anju T Sudhakar, Anton Blanchard, Arnd Bergmann,
  Athira Rajeev, Cédric Le Goater, Christian Lamparter, Christophe
  Leroy, Christophe Lombard, Christoph Hellwig, Daniel Axtens, Denis
  Efremov, Enrico Weigelt, Frederic Barrat, Gautham R. Shenoy, Geert
  Uytterhoeven, Geliang Tang, Gen Zhang, Greg Kroah-Hartman, Greg Kurz,
  Gustavo Romero, Krzysztof Kozlowski, Madhavan Srinivasan, Masahiro
  Yamada, Mathieu Malaterre, Michael Neuling, Nathan Lynch, Naveen N.
  Rao, Nicholas Piggin, Nishad Kamdar, Oliver O'Halloran, Qian Cai, Ravi
  Bangoria, Sachin Sant, Sam Bobroff, Satheesh Rajendran, Segher
  Boessenkool, Shaokun Zhang, Shawn Anastasio, Stewart Smith, Suraj
  Jitindar Singh, Thiago Jung Bauermann, YueHaibing"

* tag 'powerpc-5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (163 commits)
  powerpc/powernv/idle: Fix restore of SPRN_LDBAR for POWER9 stop state.
  powerpc/eeh: Handle hugepages in ioremap space
  ocxl: Update for AFU descriptor template version 1.1
  powerpc/boot: pass CONFIG options in a simpler and more robust way
  powerpc/boot: add {get, put}_unaligned_be32 to xz_config.h
  powerpc/irq: Don't WARN continuously in arch_local_irq_restore()
  powerpc/module64: Use symbolic instructions names.
  powerpc/module32: Use symbolic instructions names.
  powerpc: Move PPC_HA() PPC_HI() and PPC_LO() to ppc-opcode.h
  powerpc/module64: Fix comment in R_PPC64_ENTRY handling
  powerpc/boot: Add lzo support for uImage
  powerpc/boot: Add lzma support for uImage
  powerpc/boot: don't force gzipped uImage
  powerpc/8xx: Add microcode patch to move SMC parameter RAM.
  powerpc/8xx: Use IO accessors in microcode programming.
  powerpc/8xx: replace #ifdefs by IS_ENABLED() in microcode.c
  powerpc/8xx: refactor programming of microcode CPM params.
  powerpc/8xx: refactor printing of microcode patch name.
  powerpc/8xx: Refactor microcode write
  powerpc/8xx: refactor writing of CPM microcode arrays
  ...

If the kernel is notified of an HMI caused by the NPU2, it's currently
not being recognized and it logs the default message:

    Unknown Malfunction Alert of type 3

The NPU on Power 9 has 3 Fault Isolation Registers, so that's a lot of
possible causes, but we should at least log that it's an NPU problem
and report which FIR and which bit were raised if opal gave us the
information.

Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 3029 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add the macros needed for IMC (In-Memory Collection Counters) trace-mode
and data structure to hold the trace-imc record data.
Also, add the new type "OPAL_IMC_COUNTERS_TRACE" in 'opal-api.h', since
there is a new switch case added in the opal-calls for IMC.

Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

On TOD/TB errors timebase register stops/freezes until HMI error recovery
gets TOD/TB back into running state. On successful recovery, TB starts
running again and udelay() that relies on TB value continues to function
properly. But in case when HMI fails to recover from TOD/TB errors, the
TB register stay freezed. With TB not running the __delay() function
keeps looping and never return. If __delay() is called while in panic
path then system hangs and never reboots after panic.

Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The support for XIVE native exploitation mode in Linux/KVM needs a
couple more OPAL calls to get and set the state of the XIVE internal
structures being used by a sPAPR guest.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Ever since fast reboot is enabled by default in opal,
opal_cec_reboot() will use fast-reset instead of full IPL to perform
system reboot. This leaves the user with no direct way to force a full
IPL reboot except changing an nvram setting that persistently disables
fast-reset for all subsequent reboots.

This patch provides a more direct way for the user to force a one-shot
full IPL reboot by passing the command line argument 'full' to the
reboot command. So the user will be able to tweak the reboot behavior
via:

  $ sudo reboot full	# Force a full ipl reboot skipping fast-reset

  or
  $ sudo reboot  	# default reboot path (usually fast-reset)

The reboot command passes the un-parsed command argument to the kernel
via the 'Reboot' syscall which is then passed on to the arch function
pnv_restart(). The patch updates pnv_restart() to handle this cmd-arg
and issues opal_cec_reboot2 with OPAL_REBOOT_FULL_IPL to force a full
IPL reset.

Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>