When building a 64bit kernel sometimes functions in the .init section were not
able to reach the standard kernel function. Main reason for this problem is,
that the linkage tables (.plt, .opd, .dlt) tend to become pretty huge and thus
the distance gets too big for short calls.

One option to avoid this is to use the -mlong-calls compiler option, but this
increases the binary size and introduces a performance penalty.

Instead, with this patch we just lay out the binary differently.  Init code is
stored first, followed by text, R/O and finally R/W data. This means, that init
and text code is now much closer to each other, which is sufficient to reach
each other by short calls.

Signed-off-by: Helge Deller <deller@gmx.de>

Since the beginning of the parisc-linux port, sometimes 64bit SMP kernels were
not able to bring up other CPUs than the monarch CPU and instead crashed the
kernel.  The reason was unclear, esp. since it involved various machines (e.g.
J5600, J6750 and SuperDome). Testing showed, that those crashes didn't happened
when less than 4GB were installed, or if a 32bit Linux kernel was booted.

In the end, the fix for those SMP problems is trivial:
During the early phase of the initialization of the CPUs, including the monarch
CPU, the PDC_PSW firmware function to enable WIDE (=64bit) mode is called.
It's documented that this firmware function may clobber various registers, and
one one of those possibly clobbered registers is %cr30 which holds the task
thread info pointer.

Now, if %cr30 would always have been clobbered, then this bug would have been
detected much earlier. But lots of testing finally showed, that - at least for
%cr30 - on some machines only the upper 32bits of the 64bit register suddenly
turned zero after the firmware call.

So, after finding the root cause, the explanation for the various crashes
became clear:
- On 32bit SMP Linux kernels all upper 32bit were zero, so we didn't faced this
  problem.
- Monarch CPUs in 64bit mode always booted sucessfully, because the inital task
  thread info pointer was below 4GB.
- Secondary CPUs booted sucessfully on machines with less than 4GB RAM because
  the upper 32bit were zero anyay.
- Secondary CPus failed to boot if we had more than 4GB RAM and the task thread
  info pointer was located above the 4GB boundary.

Finally, the patch to fix this problem is trivial by saving the %cr30 register
before the firmware call and restoring it afterwards.

Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # 2.6.12+
Signed-off-by: Helge Deller <deller@gmx.de>

Currently parisc has the whole kernel marked as RWX, meaning any
kernel page at all is eligible to be executed.  This can cause a
theoretical problem on systems with combined I/D TLB because the act
of referencing a page causes a TLB insertion with an executable bit.
This TLB entry may be used by the CPU as the basis for speculating the
page into the I-Cache.  If this speculated page is subsequently used
for a user process, there is the possibility we will get a stale
I-cache line picked up as the binary executes.

As a point of good practise, only mark actual kernel text pages as
executable.  The same has to be done for init_text pages, but they're
converted to data pages (and the I-Cache flushed) when the init memory
is released.

Signed-off-by: James Bottomley <James.Bottomley@suse.de>

Fixes generated by 'codespell' and manually reviewed.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>

Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>

Bang in our own start_parisc call, which initializes the PDC
width, and turns on the FPU.

Previously, if CONFIG_PRINTK_TIME was on, we'd attempt to use
the FPU before we had enabled it, resulting in a difficult
to diagnose panic.

This patch causes init_per_cpu to redundantly set these for
cpu0, but this is harmless.

And explicitly list it in vmlinux.lds...

Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

This reverts commit bd3bb8c15b9a80dbddfb7905b237a4a11a4725b4.

Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

This trivial patch fixes the following section warnings on PARISC:
> WARNING: vmlinux.o (.text.1): unexpected section name.
>The (.[number]+) following section name are ld generated and not expected.
> Did you forget to use "ax"/"aw" in a .S file?
> Note that for example <linux/init.h> contains
> section definitions for use in .S files.

Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

- move boot_args[] into the init section
- move $global$ into the read_mostly section
- fix the following two section mismatches:
WARNING: vmlinux.o(.text+0x9c): Section mismatch: reference to .init.text:start_kernel (between '$pgt_fill_loop' and '$is_pa20')
WARNING: vmlinux.o(.text+0xa0): Section mismatch: reference to .init.text:start_kernel (between '$pgt_fill_loop' and '$is_pa20')

Signed-off-by: Helge Deller <deller@gmx.de>
SIgned-off-by: Kyle McMartin <kyle@mcmartin.ca>