The motivation of this renaming is to make these variables and related
helper functions less mmu_notifier bound and can also be used for non
mmu_notifier based page invalidation. mmu_invalidate_* was chosen to
better describe the purpose of 'invalidating' a page that those
variables are used for.

  - mmu_notifier_seq/range_start/range_end are renamed to
    mmu_invalidate_seq/range_start/range_end.

  - mmu_notifier_retry{_hva} helper functions are renamed to
    mmu_invalidate_retry{_hva}.

  - mmu_notifier_count is renamed to mmu_invalidate_in_progress to
    avoid confusion with mn_active_invalidate_count.

  - While here, also update kvm_inc/dec_notifier_count() to
    kvm_mmu_invalidate_begin/end() to match the change for
    mmu_notifier_count.

No functional change intended.

Signed-off-by: Chao Peng <chao.p.peng@linux.intel.com>
Message-Id: <20220816125322.1110439-3-chao.p.peng@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

KVM_PRIVATE_MEM_SLOTS defaults to zero, so it is not necessary to
define it in MIPS's asm/kvm_host.h.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Pull tty / serial driver updates from Greg KH:
 "Here is the big set of tty and serial driver changes for 6.0-rc1.

  It was delayed from last week as I wanted to make sure the last commit
  here got some good testing in linux-next and elsewhere as it seemed to
  show up only late in testing for some reason.

  Nothing major here, just lots of cleanups from Jiri and Ilpo to make
  the tty core cleaner (Jiri) and the rs485 code simpler to use (Ilpo).

  Also included in here is the obligatory n_gsm updates from Daniel
  Starke and lots of tiny driver updates and minor fixes and tweaks for
  other smaller serial drivers.

  All of these have been in linux-next for a while with no reported
  problems"

* tag 'tty-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (186 commits)
  tty: serial: qcom-geni-serial: Fix %lu -> %u in print statements
  tty: amiserial: Fix comment typo
  tty: serial: document uart_get_console()
  tty: serial: serial_core, reformat kernel-doc for functions
  Documentation: serial: link uart_ops properly
  Documentation: serial: move GPIO kernel-doc to the functions
  Documentation: serial: dedup kernel-doc for uart functions
  Documentation: serial: move uart_ops documentation to the struct
  dt-bindings: serial: snps-dw-apb-uart: Document Rockchip RV1126
  serial: mvebu-uart: uart2 error bits clearing
  tty: serial: fsl_lpuart: correct the count of break characters
  serial: stm32: make info structs static to avoid sparse warnings
  serial: fsl_lpuart: zero out parity bit in CS7 mode
  tty: serial: qcom-geni-serial: Fix get_clk_div_rate() which otherwise could return a sub-optimal clock rate.
  serial: 8250_bcm2835aux: Add missing clk_disable_unprepare()
  tty: vt: initialize unicode screen buffer
  serial: remove VR41XX serial driver
  serial: 8250: lpc18xx: Remove redundant sanity check for RS485 flags
  serial: 8250_dwlib: remove redundant sanity check for RS485 flags
  dt_bindings: rs485: Correct delay values
  ...

Pull MIPS updates from Thomas Bogendoerfer:

 - added support for Netgear WNR3500L v2

 - removed support for VR41xx SoC and platforms based on it

 - cleanups and fixes

* tag 'mips_6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (25 commits)
  MIPS: tlbex: Explicitly compare _PAGE_NO_EXEC against 0
  Revert "MIPS: octeon: Remove vestiges of CONFIG_CAVIUM_RESERVE32"
  MIPS: Introduce CAVIUM_RESERVE32 Kconfig option
  MIPS: msi-octeon: eliminate kernel-doc warnings
  MIPS: Fix comment typo
  MIPS: BMIPS: Utilize cfe_die() for invalid DTB
  MIPS: CFE: Add cfe_die()
  MIPS: Fixed __debug_virt_addr_valid()
  MIPS: BCM47XX: Add support for Netgear WNR3500L v2
  MIPS: Remove VR41xx support
  MIPS: dts: align gpio-key node names with dtschema
  MIPS: dts: correct gpio-keys names and properties
  MIPS: cpuinfo: Fix a warning for CONFIG_CPUMASK_OFFSTACK
  MIPS: Make phys_to_virt utilize __va()
  MIPS: vdso: Utilize __pa() for gic_pfn
  MIPS: mm: Use the bitmap API to allocate bitmaps
  MIPS: math-emu: Use the bitmap API to allocate bitmaps
  MIPS: Loongson64: Fix section mismatch warning
  mips: cavium-octeon: Fix missing of_node_put() in octeon2_usb_clocks_start
  MIPS: mscc: ocelot: enable FDMA usage
  ...

Pull MM updates from Andrew Morton:
 "Most of the MM queue. A few things are still pending.

  Liam's maple tree rework didn't make it. This has resulted in a few
  other minor patch series being held over for next time.

  Multi-gen LRU still isn't merged as we were waiting for mapletree to
  stabilize. The current plan is to merge MGLRU into -mm soon and to
  later reintroduce mapletree, with a view to hopefully getting both
  into 6.1-rc1.

  Summary:

   - The usual batches of cleanups from Baoquan He, Muchun Song, Miaohe
     Lin, Yang Shi, Anshuman Khandual and Mike Rapoport

   - Some kmemleak fixes from Patrick Wang and Waiman Long

   - DAMON updates from SeongJae Park

   - memcg debug/visibility work from Roman Gushchin

   - vmalloc speedup from Uladzislau Rezki

   - more folio conversion work from Matthew Wilcox

   - enhancements for coherent device memory mapping from Alex Sierra

   - addition of shared pages tracking and CoW support for fsdax, from
     Shiyang Ruan

   - hugetlb optimizations from Mike Kravetz

   - Mel Gorman has contributed some pagealloc changes to improve
     latency and realtime behaviour.

   - mprotect soft-dirty checking has been improved by Peter Xu

   - Many other singleton patches all over the place"

 [ XFS merge from hell as per Darrick Wong in

   https://lore.kernel.org/all/YshKnxb4VwXycPO8@magnolia/ ]

* tag 'mm-stable-2022-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (282 commits)
  tools/testing/selftests/vm/hmm-tests.c: fix build
  mm: Kconfig: fix typo
  mm: memory-failure: convert to pr_fmt()
  mm: use is_zone_movable_page() helper
  hugetlbfs: fix inaccurate comment in hugetlbfs_statfs()
  hugetlbfs: cleanup some comments in inode.c
  hugetlbfs: remove unneeded header file
  hugetlbfs: remove unneeded hugetlbfs_ops forward declaration
  hugetlbfs: use helper macro SZ_1{K,M}
  mm: cleanup is_highmem()
  mm/hmm: add a test for cross device private faults
  selftests: add soft-dirty into run_vmtests.sh
  selftests: soft-dirty: add test for mprotect
  mm/mprotect: fix soft-dirty check in can_change_pte_writable()
  mm: memcontrol: fix potential oom_lock recursion deadlock
  mm/gup.c: fix formatting in check_and_migrate_movable_page()
  xfs: fail dax mount if reflink is enabled on a partition
  mm/memcontrol.c: remove the redundant updating of stats_flush_threshold
  userfaultfd: don't fail on unrecognized features
  hugetlb_cgroup: fix wrong hugetlb cgroup numa stat
  ...

Pull asm-generic updates from Arnd Bergmann:
 "There are three independent sets of changes:

   - Sai Prakash Ranjan adds tracing support to the asm-generic version
     of the MMIO accessors, which is intended to help understand
     problems with device drivers and has been part of Qualcomm's vendor
     kernels for many years

   - A patch from Sebastian Siewior to rework the handling of IRQ stacks
     in softirqs across architectures, which is needed for enabling
     PREEMPT_RT

   - The last patch to remove the CONFIG_VIRT_TO_BUS option and some of
     the code behind that, after the last users of this old interface
     made it in through the netdev, scsi, media and staging trees"

* tag 'asm-generic-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
  uapi: asm-generic: fcntl: Fix typo 'the the' in comment
  arch/*/: remove CONFIG_VIRT_TO_BUS
  soc: qcom: geni: Disable MMIO tracing for GENI SE
  serial: qcom_geni_serial: Disable MMIO tracing for geni serial
  asm-generic/io: Add logging support for MMIO accessors
  KVM: arm64: Add a flag to disable MMIO trace for nVHE KVM
  lib: Add register read/write tracing support
  drm/meson: Fix overflow implicit truncation warnings
  irqchip/tegra: Fix overflow implicit truncation warnings
  coresight: etm4x: Use asm-generic IO memory barriers
  arm64: io: Use asm-generic high level MMIO accessors
  arch/*: Disable softirq stacks on PREEMPT_RT.

Pull pci updates from Bjorn Helgaas:
 "Enumeration:

   - Consolidate duplicated 'next function' scanning and extend to allow
     'isolated functions' on s390, similar to existing hypervisors
     (Niklas Schnelle)

  Resource management:
   - Implement pci_iobar_pfn() for sparc, which allows us to remove the
     sparc-specific pci_mmap_page_range() and pci_mmap_resource_range().

     This removes the ability to map the entire PCI I/O space using
     /proc/bus/pci, but we believe that's already been broken since
     v2.6.28 (Arnd Bergmann)

   - Move common PCI definitions to asm-generic/pci.h and rework others
     to be be more specific and more encapsulated in arches that need
     them (Stafford Horne)

  Power management:

   - Convert drivers to new *_PM_OPS macros to avoid need for '#ifdef
     CONFIG_PM_SLEEP' or '__maybe_unused' (Bjorn Helgaas)

  Virtualization:

   - Add ACS quirk for Broadcom BCM5750x multifunction NICs that isolate
     the functions but don't advertise an ACS capability (Pavan Chebbi)

  Error handling:

   - Clear PCI Status register during enumeration in case firmware left
     errors logged (Kai-Heng Feng)

   - When we have native control of AER, enable error reporting for all
     devices that support AER. Previously only a few drivers enabled
     this (Stefan Roese)

   - Keep AER error reporting enabled for switches. Previously we
     enabled this during enumeration but immediately disabled it (Stefan
     Roese)

   - Iterate over error counters instead of error strings to avoid
     printing junk in AER sysfs counters (Mohamed Khalfella)

  ASPM:

   - Remove pcie_aspm_pm_state_change() so ASPM config changes, e.g.,
     via sysfs, are not lost across power state changes (Kai-Heng Feng)

  Endpoint framework:

   - Don't stop an EPC when unbinding an EPF from it (Shunsuke Mie)

  Endpoint embedded DMA controller driver:

   - Simplify and clean up support for the DesignWare embedded DMA
     (eDMA) controller (Frank Li, Serge Semin)

  Broadcom STB PCIe controller driver:

   - Avoid config space accesses when link is down because we can't
     recover from the CPU aborts these cause (Jim Quinlan)

   - Look for power regulators described under Root Ports in DT and
     enable them before scanning the secondary bus (Jim Quinlan)

   - Disable/enable regulators in suspend/resume (Jim Quinlan)

  Freescale i.MX6 PCIe controller driver:

   - Simplify and clean up clock and PHY management (Richard Zhu)

   - Disable/enable regulators in suspend/resume (Richard Zhu)

   - Set PCIE_DBI_RO_WR_EN before writing DBI registers (Richard Zhu)

   - Allow speeds faster than Gen2 (Richard Zhu)

   - Make link being down a non-fatal error so controller probe doesn't
     fail if there are no Endpoints connected (Richard Zhu)

  Loongson PCIe controller driver:

   - Add ACPI and MCFG support for Loongson LS7A (Huacai Chen)

   - Avoid config reads to non-existent LS2K/LS7A devices because a
     hardware defect causes machine hangs (Huacai Chen)

   - Work around LS7A integrated devices that report incorrect Interrupt
     Pin values (Jianmin Lv)

  Marvell Aardvark PCIe controller driver:

   - Add support for AER and Slot capability on emulated bridge (Pali
     Rohár)

  MediaTek PCIe controller driver:

   - Add Airoha EN7532 to DT binding (John Crispin)

   - Allow building of driver for ARCH_AIROHA (Felix Fietkau)

  MediaTek PCIe Gen3 controller driver:

   - Print decoded LTSSM state when the link doesn't come up (Jianjun
     Wang)

  NVIDIA Tegra194 PCIe controller driver:

   - Convert DT binding to json-schema (Vidya Sagar)

   - Add DT bindings and driver support for Tegra234 Root Port and
     Endpoint mode (Vidya Sagar)

   - Fix some Root Port interrupt handling issues (Vidya Sagar)

   - Set default Max Payload Size to 256 bytes (Vidya Sagar)

   - Fix Data Link Feature capability programming (Vidya Sagar)

   - Extend Endpoint mode support to devices beyond Controller-5 (Vidya
     Sagar)

  Qualcomm PCIe controller driver:

   - Rework clock, reset, PHY power-on ordering to avoid hangs and
     improve consistency (Robert Marko, Christian Marangi)

   - Move pipe_clk handling to PHY drivers (Dmitry Baryshkov)

   - Add IPQ60xx support (Selvam Sathappan Periakaruppan)

   - Allow ASPM L1 and substates for 2.7.0 (Krishna chaitanya chundru)

   - Add support for more than 32 MSI interrupts (Dmitry Baryshkov)

  Renesas R-Car PCIe controller driver:

   - Convert DT binding to json-schema (Herve Codina)

   - Add Renesas RZ/N1D (R9A06G032) to rcar-gen2 DT binding and driver
     (Herve Codina)

  Samsung Exynos PCIe controller driver:

   - Fix phy-exynos-pcie driver so it follows the 'phy_init() before
     phy_power_on()' PHY programming model (Marek Szyprowski)

  Synopsys DesignWare PCIe controller driver:

   - Simplify and clean up the DWC core extensively (Serge Semin)

   - Fix an issue with programming the ATU for regions that cross a 4GB
     boundary (Serge Semin)

   - Enable the CDM check if 'snps,enable-cdm-check' exists; previously
     we skipped it if 'num-lanes' was absent (Serge Semin)

   - Allocate a 32-bit DMA-able page to be MSI target instead of using a
     driver data structure that may not be addressable with 32-bit
     address (Will McVicker)

   - Add DWC core support for more than 32 MSI interrupts (Dmitry
     Baryshkov)

  Xilinx Versal CPM PCIe controller driver:

   - Add DT binding and driver support for Versal CPM5 Gen5 Root Port
     (Bharat Kumar Gogada)"

* tag 'pci-v5.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (150 commits)
  PCI: imx6: Support more than Gen2 speed link mode
  PCI: imx6: Set PCIE_DBI_RO_WR_EN before writing DBI registers
  PCI: imx6: Reformat suspend callback to keep symmetric with resume
  PCI: imx6: Move the imx6_pcie_ltssm_disable() earlier
  PCI: imx6: Disable clocks in reverse order of enable
  PCI: imx6: Do not hide PHY driver callbacks and refine the error handling
  PCI: imx6: Reduce resume time by only starting link if it was up before suspend
  PCI: imx6: Mark the link down as non-fatal error
  PCI: imx6: Move regulator enable out of imx6_pcie_deassert_core_reset()
  PCI: imx6: Turn off regulator when system is in suspend mode
  PCI: imx6: Call host init function directly in resume
  PCI: imx6: Disable i.MX6QDL clock when disabling ref clocks
  PCI: imx6: Propagate .host_init() errors to caller
  PCI: imx6: Collect clock enables in imx6_pcie_clk_enable()
  PCI: imx6: Factor out ref clock disable to match enable
  PCI: imx6: Move imx6_pcie_clk_disable() earlier
  PCI: imx6: Move imx6_pcie_enable_ref_clk() earlier
  PCI: imx6: Move PHY management functions together
  PCI: imx6: Move imx6_pcie_grp_offset(), imx6_pcie_configure_type() earlier
  PCI: imx6: Convert to NOIRQ_SYSTEM_SLEEP_PM_OPS()
  ...

Pull USB / Thunderbolt updates from Greg KH:
 "Here is the big set of Thunderbolt and USB changes for 6.0-rc1.

  Lots of little things here, nothing major, just constant development
  on some new hardware support and cleanups of older drivers. Highlights
  are:

   - lots of typec changes and improvements for new hardware

   - new gadget controller driver

   - thunderbolt support for new hardware

   - the normal set of new usb-serial device ids and cleanups

   - loads of dwc3 controller fixes and improvements

   - mtu3 driver updates

   - testusb fixes for longtime issues (not many people use this tool it
     seems.)

   - minor driver fixes and improvements over the USB tree

   - chromeos platform driver changes were added and then reverted as
     they depened on some typec changes, but the cross-tree merges
     caused problems so they will come back later through the platform
     tree.

  All of these have been in linux-next for a while now with no reported
  issues"

* tag 'usb-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (193 commits)
  usb: misc: onboard_usb_hub: Remove duplicated power_on delay
  usb: misc: onboard_usb_hub: Add TI USB8041 hub support
  usb: misc: onboard_usb_hub: Add reset-gpio support
  USB: usbsevseg: convert sysfs snprintf to sysfs_emit
  dt-bindings: usb: Add binding for TI USB8041 hub controller
  ARM: multi_v7_defconfig: enable USB onboard HUB driver
  ARM: dts: stm32: add support for USB2514B onboard hub on stm32mp15xx-dkx
  usb: misc: onboard-hub: add support for Microchip USB2514B USB 2.0 hub
  dt-bindings: usb: generic-ehci: allow usb-hcd schema properties
  usb: typec: ucsi: stm32g0: add bootloader support
  usb: typec: ucsi: stm32g0: add support for stm32g0 controller
  dt-bindings: usb: typec: add bindings for stm32g0 controller
  usb: typec: ucsi: Acknowledge the GET_ERROR_STATUS command completion
  usb: cdns3: change place of 'priv_ep' assignment in cdns3_gadget_ep_dequeue(), cdns3_gadget_ep_enable()
  usb/chipidea: fix repeated words in comments
  usb: renesas-xhci: Do not print any log while fw verif success
  usb: typec: retimer: Add missing id check in match callback
  USB: xhci: Fix comment typo
  usb/typec/tcpm: fix repeated words in comments
  usb/musb: fix repeated words in comments
  ...

When CONFIG_XPA is enabled, Clang warns:

  arch/mips/mm/tlbex.c:629:24: error: converting the result of '<<' to a boolean; did you mean '(1 << _PAGE_NO_EXEC_SHIFT) != 0'? [-Werror,-Wint-in-bool-context]
          if (cpu_has_rixi && !!_PAGE_NO_EXEC) {
                              ^
  arch/mips/include/asm/pgtable-bits.h:174:28: note: expanded from macro '_PAGE_NO_EXEC'
  # define _PAGE_NO_EXEC          (1 << _PAGE_NO_EXEC_SHIFT)
                                     ^
  arch/mips/mm/tlbex.c:2568:24: error: converting the result of '<<' to a boolean; did you mean '(1 << _PAGE_NO_EXEC_SHIFT) != 0'? [-Werror,-Wint-in-bool-context]
          if (!cpu_has_rixi || !_PAGE_NO_EXEC) {
                                ^
  arch/mips/include/asm/pgtable-bits.h:174:28: note: expanded from macro '_PAGE_NO_EXEC'
  # define _PAGE_NO_EXEC          (1 << _PAGE_NO_EXEC_SHIFT)
                                     ^
  2 errors generated.

_PAGE_NO_EXEC can be '0' or '1 << _PAGE_NO_EXEC_SHIFT' depending on the
build and runtime configuration, which is what the negation operators
are trying to convey. To silence the warning, explicitly compare against
0 so the result of the '<<' operator is not implicitly converted to a
boolean.

According to its documentation, GCC enables -Wint-in-bool-context with
-Wall but this warning is not visible when building the same
configuration with GCC. It appears GCC only warns when compiling C++,
not C, although the documentation makes no note of this:
https://godbolt.org/z/x39q3brxf

Reported-by: Sudip Mukherjee (Codethink) <sudipm.mukherjee@gmail.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

Pull uapi flexible array update from Gustavo Silva:
 "A treewide patch that replaces zero-length arrays with flexible-array
  members in UAPI. This has been baking in linux-next for 5 weeks now.

  '-fstrict-flex-arrays=3' is coming and we need to land these changes
  to prevent issues like these in the short future:

    fs/minix/dir.c:337:3: warning: 'strcpy' will always overflow; destination buffer has size 0, but the source string has length 2 (including NUL byte) [-Wfortify-source]
		strcpy(de3->name, ".");
		^

  Since these are all [0] to [] changes, the risk to UAPI is nearly
  zero. If this breaks anything, we can use a union with a new member
  name"

Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=101836

* tag 'flexible-array-transformations-UAPI-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
  treewide: uapi: Replace zero-length arrays with flexible-array members