machine_early_init is defined in arch/microblaze/kernel/setup.c
I do not see mach-* directory for MicroBlaze.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Switch to the generic noncoherent direct mapping implementation.

This removes the direction-based optimizations in
sync_{single,sg}_for_{cpu,device} which were marked untestested and
do not match the usually very well tested {un,}map_{single,sg}
implementations.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Now that platform.c only has the GPIO reset handling left, move the
initcall to reset.c and remove platform.c.

Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

The call to of_platform_bus_probe has no effect because the DT core
already probes default buses like "simple-bus" before this call.
Michal Simek said 'xlnx,compound' hasn't been used in a long time, so
that match entry isn't needed.

Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Wire up new syscalls io_pgetevents and rseq.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

There is no reason to keep this gpio based code in architecture. Use
ledtrig-heartbeat.c instead which is much more flexible then this
ancient code.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Since commit 96f0e6fcc9ad ("microblaze: remove redundant early_printk
support") prom.h was removed and one instance in heartbeat.c remained.
Include of.h as it is the actual header needed.

Fixes: 96f0e6fcc9ad ("microblaze: remove redundant early_printk support")
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Pull microblaze updates from Michal Simek:

 - Fix simpleImage format generation

 - Remove earlyprintk support and replace it by earlycon

* tag 'microblaze-v4.18-rc1' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: dts: replace 'linux,stdout-path' with 'stdout-path'
  microblaze: remove redundant early_printk support
  microblaze: remove unnecessary prom.h includes
  microblaze: Fix simpleImage format generation

Pull siginfo updates from Eric Biederman:
 "This set of changes close the known issues with setting si_code to an
  invalid value, and with not fully initializing struct siginfo. There
  remains work to do on nds32, arc, unicore32, powerpc, arm, arm64, ia64
  and x86 to get the code that generates siginfo into a simpler and more
  maintainable state. Most of that work involves refactoring the signal
  handling code and thus careful code review.

  Also not included is the work to shrink the in kernel version of
  struct siginfo. That depends on getting the number of places that
  directly manipulate struct siginfo under control, as it requires the
  introduction of struct kernel_siginfo for the in kernel things.

  Overall this set of changes looks like it is making good progress, and
  with a little luck I will be wrapping up the siginfo work next
  development cycle"

* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (46 commits)
  signal/sh: Stop gcc warning about an impossible case in do_divide_error
  signal/mips: Report FPE_FLTUNK for undiagnosed floating point exceptions
  signal/um: More carefully relay signals in relay_signal.
  signal: Extend siginfo_layout with SIL_FAULT_{MCEERR|BNDERR|PKUERR}
  signal: Remove unncessary #ifdef SEGV_PKUERR in 32bit compat code
  signal/signalfd: Add support for SIGSYS
  signal/signalfd: Remove __put_user from signalfd_copyinfo
  signal/xtensa: Use force_sig_fault where appropriate
  signal/xtensa: Consistenly use SIGBUS in do_unaligned_user
  signal/um: Use force_sig_fault where appropriate
  signal/sparc: Use force_sig_fault where appropriate
  signal/sparc: Use send_sig_fault where appropriate
  signal/sh: Use force_sig_fault where appropriate
  signal/s390: Use force_sig_fault where appropriate
  signal/riscv: Replace do_trap_siginfo with force_sig_fault
  signal/riscv: Use force_sig_fault where appropriate
  signal/parisc: Use force_sig_fault where appropriate
  signal/parisc: Use force_sig_mceerr where appropriate
  signal/openrisc: Use force_sig_fault where appropriate
  signal/nios2: Use force_sig_fault where appropriate
  ...

Most mainstream architectures are using 65536 entries, so lets stick to
that.  If someone is really desperate to override it that can still be
done through <asm/dma-mapping.h>, but I'd rather see a really good
rationale for that.

dma_debug_init is now called as a core_initcall, which for many
architectures means much earlier, and provides dma-debug functionality
earlier in the boot process.  This should be safe as it only relies
on the memory allocator already being available.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>