Pull i2c fixes from Wolfram Sang:
 "Bugfixes for the i2c subsystem.

  Except for a few one-liners, there is mainly one revert because of an
  overlooked dependency.  Since there is no linux-next at the moment, I
  did some extra testing, and all was fine for me."

* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
  i2c: mxs: Handle i2c DMA failure properly
  i2c: s3c2410: Fix code to free gpios
  i2c: omap: ensure writes to dev->buf_len are ordered
  Revert "ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints"
  i2c: at91: fix SMBus quick command

Pull one more ARM SoC fix from Olof Johansson:
 "I missed one pull request from Samsung with one fix in the previous
  batch.  Here it is -- a dma driver fix for an early version of silicon
  that they still support."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: EXYNOS: PL330 MDMA1 fix for revision 0 of Exynos4210 SOC

Pull input updates from Dmitry Torokhov:
 "This fixes recent regression where /dev/input/mice got assigned wrong
  device node which messed up setups with static /dev, and a regression
  in ads7846 GPIO debounce setup."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  ARM - OMAP: ads7846: fix pendown debounce setting
  Input: ads7846 - enable pendown GPIO debounce time setting
  Input: mousedev - move /dev/input/mice to the correct minor
  Input: MT - document new 'flags' argument of input_mt_init_slots()

From Kukjin Kim:

Here is Samsung fixes for v3.7 and it is for fixing of mdma1 address
for exynos4210 rev0 SoC.

* 'v3.7-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: EXYNOS: PL330 MDMA1 fix for revision 0 of Exynos4210 SOC

Signed-off-by: Olof Johansson <olof@lixom.net>

From Tony Lindgren:
Few more regression fixes related to u-boot only muxing
essential pins.

* tag 'omap-for-v3.7-rc5/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP4: TWL: mux sys_drm_msecure as output for PMIC
  ARM: OMAP3: igep0020: Set WIFI/BT GPIO pins in correct mux mode
  ARM: OMAP: Add maintainer entry for IGEP machines

Commit 97ee9f01 (ARM: OMAP: fix the ads7846 init code) have enabled the
pendown GPIO debounce time setting by the below sequence:

  gpio_request_one()
  gpio_set_debounce()
  gpio_free()

It also revealed a bug in the OMAP GPIO handling code which prevented
the GPIO debounce clock to be disabled and CORE transition to low power
states.

Commit c9c55d9 (gpio/omap: fix off-mode bug: clear debounce settings on
free/reset) fixes the OMAP GPIO handling code by making sure that the
GPIO debounce clock gets disabled if no GPIO is requested from current
bank.

While fixing the OMAP GPIO handling code (in the right way), the above
commit makes the gpio_request->set_debounce->free sequence invalid as
after freeing the GPIO, the debounce settings are lost.

Fix the debounce settings by moving the debounce initialization to the
actual GPIO requesting code - the ads7846 driver.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Commit 8214513 ("ARM: EXYNOS: fix address for EXYNOS4 MDMA1")
changed EXYNOS specific setup of PL330 DMA engine to use 'non-secure'
mdma1 address instead of 'secure' one (from 0x12840000 to 0x12850000)
to fix issue with some Exynos4212 SOCs.  Unfortunately it brakes
PL330 setup for revision 0 of Exynos4210 SOC (mdma1 device cannot
be found at 'non-secure' address):

[    0.566245] dma-pl330 dma-pl330.2: PERIPH_ID 0x0, PCELL_ID 0x0 !
[    0.566278] dma-pl330: probe of dma-pl330.2 failed with error -22

Fix it by using 'secure' mdma1 address on Exynos4210 revision 0 SOC.

Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Fix the video clock setting when custom timings are used with
pclock <= 27MHz. Existing video clock selection uses PLL2 mode
which results in a 54MHz clock whereas using the MXI mode results
in a 27MHz clock (which is the one actually desired).

This bug affects the Enhanced Definition (ED) support on DM644x.
Without this patch, out-range signals errors are were observed on
the TV when viewing ED. An out-of-range signal is often caused when
the field rate is above the rate that the television will handle.

Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
[nsekhar@ti.com: reword commit message based on on-list discussion]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

From Nicolas Ferre <nicolas.ferre@atmel.com>:

Two little fixes, one related to the move to sparse irq and
another one fixing the check of a GPIO for USB host overcurrent.

* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
  ARM: at91/usbh: fix overcurrent gpio setup
  ARM: at91/AT91SAM9G45: fix crypto peripherals irq issue due to sparse irq support

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

From Sascha Hauer <s.hauer@pengutronix.de>:

ARM i.MX fixes for 3.7-rc

* tag 'imx-fixes-rc' of git://git.pengutronix.de/git/imx/linux-2.6:
  ARM: imx: ehci: fix host power mask bit
  ARM i.MX: fix error-valued pointer dereference in clk_register_gate2()

Signed-off-by: Arnd Bergmann <arnd@arndb.de>