Pull SH driver fix from Simon Horman:
 "Confine SH_INTC to platforms that need it"

* tag 'renesas-sh-drivers-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  sh: intc: Confine SH_INTC to platforms that need it

On r8a7791, i2c6 (aka iic3) doesn't need pinmux, but the koelsch dts
refers to non-existent pinmux configuration data:

pinmux core: sh-pfc does not support function i2c6
sh-pfc e6060000.pfc: invalid function i2c6 in map table

Remove it to fix this.

Fixes: commit 1d41f36a68c0f4e9b01d563ce33bab5201858b54 ("ARM: shmobile:
       koelsch dts: Add VDD MPU regulator for DVFS")

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Olof Johansson <olof@lixom.net>

Working on Gigabit/PCIe support in U-Boot for Apalis T30 I realised
that the current device tree source includes for our modules only
happen to work due to referencing the on-carrier 5v0 supply from USB
which is not at all available on-module. The modules actually contain
TPS60150 charge pumps to generate the PMIC required 5 volts from the
one and only 3.3 volt module supply. This patch fixes this.

(Note: When back-porting this to v3.16 stable releases, simply drop the
change to tegra30-apalis.dtsi; that file was added in v3.17)

Cc: <stable@vger.kernel.org> #v3.16+
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge "ARM: rockchip: fix for 3.17" from Heiko Stubner:

Pinctrl that got accidentially dropped when reorganizing the
dts files and addition of the new Rockchip list to MAINTAINERS.

* tag 'v3.17-rockchip-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  MAINTAINERS: add new Rockchip SoC list
  ARM: dts: rockchip: readd missing mmc0 pinctrl settings

Signed-off-by: Olof Johansson <olof@lixom.net>

During the restructuring of the Rockchip Cortex-A9 dtsi files it seems
like the pinctrl settings vanished at some point from the mmc0 support.

This of course renders them unusable, so readd the necessary pinctrl
properties.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Merge "Allwinner DT changes, take 2" from Maxime Ripard:

Only a single patch in here that fixes a DTC warning.

* tag 'sunxi-dt-for-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
  ARM: dt: sun6i: Add #address-cells and #size-cells to i2c controller nodes

Signed-off-by: Olof Johansson <olof@lixom.net>

Currently the sh-intc driver is compiled on all SuperH and
non-multiplatform SH-Mobile platforms, while it's only used on a limited
number of platforms:
  - SuperH: SH2(A), SH3(A), SH4(A)(L) (all but SH5)
  - ARM: sh7372, sh73a0

Drop the "default y" on SH_INTC, make all CPU platforms that use it
select it, and protect all sub-options by "if SH_INTC" to fix this.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Increase max i2c bus frequency beyond the default for faster
data transfers. According to the manual, these faster speeds are
only available when the board is wired up the right way. In this case,
the vendor kernel has run at this speed for a long time.

sda-delay is needed for talking to RTC on PMIC, otherwise the i2c
controller never sees an ACK. Strangely the other PMIC i2c slave (the
main one) works fine even without this delay. I Chose value 100 to
match the vendor kernel.

Signed-off-by: Daniel Drake <drake@endlessm.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Tested-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

The ODROID kernel shows that the PMIC interrupt line is hooked up
to pin GPX3-2.

This is needed for the max77686-irq driver to create the PMIC IRQ
domain, which is needed by max77686-rtc.

Signed-off-by: Daniel Drake <drake@endlessm.com>
Tested-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

The current pinfunc define all uart CTS_B IO port for DCE uart 'CTS_B'
IP port. Since uart IP port 'CTS_B' is output, and it don't need to
set 'SELECT_INPUT' bit.

Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>