Qualcomm ARM64 DTS one more fix for 5.15

This reverts a clock change in the Qualcomm RB5 devicetree which in some
combinations of firmware and configuration causes the device to crash
during boot.

Data on an adjacent platform indicates that this is probably not be the
root cause of the problem, but this resolves the regression seen on RB5
and will allow the SM8250 platform to boot v5.15.

* tag 'qcom-arm64-fixes-for-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
  Revert "arm64: dts: qcom: sm8250: remove bus clock from the mdss node for sm8250 target"

Link: https://lore.kernel.org/r/20211025201213.1145348-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

This reverts commit 001ce9785c0674d913531345e86222c965fc8bf4.

This upstream commit broke AOSP (post Android 12 merge) build
on RB5. The device either silently crashes into USB crash mode
after android boot animation or we see a blank blue screen
with following dpu errors in dmesg:

[  T444] hw recovery is not complete for ctl:3
[  T444] [drm:dpu_encoder_phys_vid_prepare_for_kickoff:539] [dpu error]enc31 intf1 ctl 3 reset failure: -22
[  T444] [drm:dpu_encoder_phys_vid_wait_for_commit_done:513] [dpu error]vblank timeout
[  T444] [drm:dpu_kms_wait_for_commit_done:454] [dpu error]wait for commit done returned -110
[    C7] [drm:dpu_encoder_frame_done_timeout:2127] [dpu error]enc31 frame done timeout
[  T444] [drm:dpu_encoder_phys_vid_wait_for_commit_done:513] [dpu error]vblank timeout
[  T444] [drm:dpu_kms_wait_for_commit_done:454] [dpu error]wait for commit done returned -110

Fixes: 001ce9785c06 ("arm64: dts: qcom: sm8250: remove bus clock from the mdss node for sm8250 target")
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211014135410.4136412-1-dmitry.baryshkov@linaro.org

Two patches to fix the GMAC PHY mode on some boards.

* tag 'sunxi-fixes-for-5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  ARM: dts: sun7i: A20-olinuxino-lime2: Fix ethernet phy-mode
  arm64: dts: allwinner: h5: NanoPI Neo 2: Fix ethernet node

Link: https://lore.kernel.org/r/d4c41c71-f1ff-4464-a26f-1bfd4b52fd78.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

i.MX fixes for 5.15, round 4:

- A series from Frieder Schrempf to fix i.MX8MM Kontron N801x board on
  various aspects, voltage settings, GPIO polarity, SPI clock frequency
  and Ethernet PHY type.

* tag 'imx-fixes-5.15-4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  arm64: dts: imx8mm-kontron: Fix connection type for VSC8531 RGMII PHY
  arm64: dts: imx8mm-kontron: Fix CAN SPI clock frequency
  arm64: dts: imx8mm-kontron: Fix polarity of reg_rst_eth2
  arm64: dts: imx8mm-kontron: Set lower limit of VDD_SNVS to 800 mV
  arm64: dts: imx8mm-kontron: Make sure SOC and DRAM supply voltages are correct

Link: https://lore.kernel.org/r/20211018000958.GC25810@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Previously we falsely relied on the PHY driver to unconditionally
enable the internal RX delay. Since the following fix for the PHY
driver this is not the case anymore:

commit 7b005a1742be ("net: phy: mscc: configure both RX and TX internal
delays for RGMII")

In order to enable the delay we need to set the connection type to
"rgmii-rxid". Without the RX delay the ethernet is not functional at
all.

Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The MCP2515 can be used with an SPI clock of up to 10 MHz. Set the
limit accordingly to prevent any performance issues caused by the
really low clock speed of 100 kHz.

This removes the arbitrarily low limit on the SPI frequency, that was
caused by a typo in the original dts.

Without this change, receiving CAN messages on the board beyond a
certain bitrate will cause overrun errors (see 'ip -det -stat link show
can0').

With this fix, receiving messages on the bus works without any overrun
errors for bitrates up to 1 MBit.

Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The regulator reg_rst_eth2 should keep the reset signal of the USB ethernet
adapter deasserted anytime. Fix the polarity and mark it as always-on.

Anyway, using the regulator is only a workaround for the missing support of
specifying a reset GPIO for USB devices in a generic way. As we don't
have a solution for this at the moment, at least fix the current
workaround.

Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to the datasheet the typical value for VDD_SNVS should be
800 mV, so let's make sure that this is within the range of the
regulator.

Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

It looks like the voltages for the SOC and DRAM supply weren't properly
validated before. The datasheet and uboot-imx code tells us that VDD_SOC
should be 800 mV in suspend and 850 mV in run mode. VDD_DRAM should be
950 mV for DDR clock frequencies of up to 1.5 GHz.

Let's fix these values to make sure the voltages are within the required
range.

Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pull ARM SoC fixes from Arnd Bergmann:
 "This is a larger than normal update for Arm SoC specific code, most of
  it in device trees, but also drivers and the omap and at91/sama7
  platforms:

   - There are four new entries to the MAINTAINERS file: Sven Peter and
     Alyssa Rosenzweig for Apple M1, Romain Perier for Mstar/sigmastar,
     and Vignesh Raghavendra for TI K3

   - Build fixes to address randconfig warnings in sharpsl, dove, omap1,
     and qcom platforms as well as the scmi and op-tee subsystems

   - Regression fixes for missing CONFIG_FB and other options for
     several defconfigs

   - Several bug fixes for the newly added Microchip SAMA7 platform,
     mostly regarding power management

   - Missing SMP barriers to protect accesses to SCMI virtio device

   - Regression fixes for TI OMAP, including a boot-time hang on am335x.

   - Lots of bug fixes for NXP i.MX, mostly addressing incorrect
     settings in devicetree files, and one revert for broken suspend.

   - Fixes for ARM Juno/Vexpress devicetree files, addressing a couple
     of schema warnings.

   - Regression fixes for qualcomm SoC specific drivers and devicetree
     files, reverting an mdt_loader change and at least pastially
     reverting some of the 5.15 DTS changes, plus some minor bugfixes"

* tag 'armsoc-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (64 commits)
  MAINTAINERS: Add Sven Peter as ARM/APPLE MACHINE maintainer
  MAINTAINERS: Add Alyssa Rosenzweig as M1 reviewer
  firmware: arm_scmi: Add proper barriers to scmi virtio device
  firmware: arm_scmi: Simplify spinlocks in virtio transport
  ARM: dts: omap3430-sdp: Fix NAND device node
  bus: ti-sysc: Use CLKDM_NOAUTO for dra7 dcan1 for errata i893
  ARM: sharpsl_param: work around -Wstringop-overread warning
  ARM: defconfig: gemini: Restore framebuffer
  ARM: dove: mark 'putc' as inline
  ARM: omap1: move omap15xx local bus handling to usb.c
  MAINTAINERS: Add Vignesh to TI K3 platform maintainership
  arm64: dts: imx8m*-venice-gw7902: fix M2_RST# gpio
  ARM: imx6: disable the GIC CPU interface before calling stby-poweroff sequence
  arm64: dts: ls1028a: fix eSDHC2 node
  arm64: dts: imx8mm-kontron-n801x-som: do not allow to switch off buck2
  ARM: dts: at91: sama7g5ek: to not touch slew-rate for SDMMC pins
  ARM: dts: at91: sama7g5ek: use proper slew-rate settings for GMACs
  ARM: at91: pm: preload base address of controllers in tlb
  ARM: at91: pm: group constants and addresses loading
  ARM: dts: at91: sama7g5ek: add suspend voltage for ddr3l rail
  ...