ARM64: hisi fixes for 4.18

- Added power capabilities for the mmc host controller on the
  hikey and hikey960 boards to avoid broken wifi.

* tag 'hisi-fixes-for-4.18' of git://github.com/hisilicon/linux-hisi:
  arm64: dts: hikey960: Define wl1837 power capabilities
  arm64: dts: hikey: Define wl1835 power capabilities

Signed-off-by: Olof Johansson <olof@lixom.net>

Amlogic fixes for v4.18-rc
- minor 64-bit DT fixes

* tag 'amlogic-fixes' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM64: dts: meson-gxl: fix Mali GPU compatible string
  ARM64: dts: meson-axg: fix ethernet stability issue
  ARM64: dts: meson-gx: fix ATF reserved memory region
  ARM64: dts: meson-gxl-s905x-p212: Add phy-supply for usb0
  ARM64: dts: meson: fix register ranges for SD/eMMC
  ARM64: dts: meson: disable sd-uhs modes on the libretech-cc

Signed-off-by: Olof Johansson <olof@lixom.net>

These properties are required for compatibility with runtime PM.
Without these properties, MMC host controller will not be aware
of power capabilities. When the wlcore driver attempts to power
on the device, it will erroneously fail with -EACCES. This fixes
a regression found here: https://lkml.org/lkml/2018/6/12/930

Fixes: 60f36637bbbd ("wlcore: sdio: allow pm to handle sdio power")
Signed-off-by: Ryan Grachek <ryan@edited.us>
Tested-by: John Stultz <john.stultz@linaro.org>
Acked-by: John Stultz <john.stultz@linaro.org>
Tested-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>

These properties are required for compatibility with runtime PM.
Without these properties, MMC host controller will not be aware
of power capabilities. When the wlcore driver attempts to power
on the device, it will erroneously fail with -EACCES.

Fixes: 60f36637bbbd ("wlcore: sdio: allow pm to handle sdio power")
Signed-off-by: Ryan Grachek <ryan@edited.us>
Tested-by: John Stultz <john.stultz@linaro.org>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>

meson-gxl-mali.dtsi is only used on GXL SoCs. Thus it should use the GXL
specific compatible string instead of the GXBB one.
For now this is purely cosmetic since the (out-of-tree) lima driver for
this GPU currently uses the "arm,mali-450" match instead of the SoC
specific one. However, update the .dts to match the documentation since
this driver behavior might change in the future.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

Like the odroid-c2 and wetek, the s400 uses the RTL8211F and seems to
suffer from the kind of stability issue.

Doing an iperf3 download test, we can see a significant number of LPI
interrupts on the tx path. After a short while (5 to 15 seconds), the
network connection dies. If using rootfs over NFS, the connection may
also break during the boot sequence.

We still don't have a real explanation for this problem so let's disable
EEE once again.

Fixes: f6f6ac914b82 ("ARM64: dts: meson-axg: enable ethernet for A113D S400 board")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

Vendor firmware/uboot has different reserved regions depending on
firmware version, but current codebase reserves the same regions on
GXL and GXBB, so move the additional reserved memory region to common
.dtsi.

Found when putting a recent vendor u-boot on meson-gxbb-p200.

Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Cc: stable@vger.kernel.org
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

Like LibreTech-CC, the USB0 needs the 5V regulator to be enabled to power the
devices on the P212 Reference Design based boards.

Fixes: b9f07cb4f41f ("ARM64: dts: meson-gxl-s905x-p212: enable the USB controller")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

Based on updated information from Amlogic, correct the register range
for the SD/eMMC blocks to the right size.

Reported-by: Yixun Lan <yixun.lan@amlogic.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

There is a problem with the sd-uhs mode when doing a soft reboot.
Switching back from 1.8v to 3.3v messes with the card, which no longer
respond (timeout errors). According to the specification, we should
perform a card reset (power cycling the card) but this is something we
cannot control on this design.

Then the only solution to restore the communication with the card is an
"unplug-plug" which is not acceptable

Until we find a solution, if any, disable the sd-uhs modes on this design.
For the people using uhs at the moment, there will a performance drop as
a result.

Fixes: 3cde63ebc85c ("ARM64: dts: meson-gxl: libretech-cc: enable high speed modes")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Cc: stable@vger.kernel.org
Signed-off-by: Kevin Hilman <khilman@baylibre.com>