The PMU node has no working interrupt, as shown by this dtc warning:

arch/arm64/boot/dts/altera/socfpga_stratix10_socdk.dtb: Warning (interrupts_property): Missing interrupt-parent for /pmu

This adds an interrupt-parent property so we can correct parse
that interrupt number.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

mvebu fixess for 4.15 (part 1)

2 device tree related fixes fixing 2 issues:
 - broken pinctrl support since 4.11 on OpenBlocks A7
 - implicit clock dependency making the kernel hang if the Xenon sdhci
   module was loaded before the mvpp2 Ethernet support (for this one
   the driver had to be fixed which was done in v4.14)

* tag 'mvebu-fixes-4.15-1' of git://git.infradead.org/linux-mvebu:
  ARM64: dts: marvell: armada-cp110: Fix clock resources for various node
  ARM: dts: kirkwood: fix pin-muxing of MPP7 on OpenBlocks A7

Signed-off-by: Olof Johansson <olof@lixom.net>

On the CP modules we found on Armada 7K/8K, many IP block actually also
need a "functional" clock (from the bus). This patch add them which allows
to fix some issues hanging the kernel:

If Ethernet and sdhci driver are built as modules and sdhci was loaded
first then the kernel hang.

Fixes: bb16ea1742c8 ("mmc: sdhci-xenon: Fix clock resource by adding an
optional bus clock")
Cc: stable@vger.kernel.org
Reported-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

This is probably a copy-paste mistake.  The gpio-ranges of PXs3 is
different from that of LD20.

Fixes: 277b51e7050f ("arm64: dts: uniphier: add GPIO controller nodes")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Pull "Allwinner fixes for 4.15" from Chen-Yu Tsai:

First, one fix that adds proper regulator references for the EMAC
external PHYs on A64 boards. The EMAC bindings were developed for 4.13,
but reverted at the last minute. They were finalized and brought back
for 4.15. However in the time between, regulator support for the A64
boards was merged. When EMAC device tree changes were reintroduced,
this was not taken into account.

Second, a patch that adds OF based modalias uevent for RSB slave devices.
This has been missing since the introduction of RSB, and recently with
PMIC regulator support introduced for the A64, has been seen affecting
distributions, which have the all-important PMIC mfd drivers built as
modules, which then don't get loaded.

Other minor cleanups include final conversion of raw indices to CCU
binding macros for sun[4567]i HDMI, cleanup of dummy regulators on the
A64 SOPINE, a SD card detection polarity fix for the Orange Pi Zero
Plus2, and adding a missing compatible for the PMIC on the TBS A711
tablet.

* tag 'sunxi-fixes-for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  ARM: dts: sun8i: a711: Reinstate the PMIC compatible
  arm64: dts: orange-pi-zero-plus2: fix sdcard detect
  arm64: allwinner: a64-sopine: Fix to use dcdc1 regulator instead of vcc3v3
  ARM: dts: sunxi: Convert to CCU index macros for HDMI controller
  sunxi-rsb: Include OF based modalias in device uevent
  arm64: allwinner: a64: add Ethernet PHY regulator for several boards

Pull "Renesas ARM Based SoC Fixes for v4.15" from Simon Horman:

Vladimir Zapolskiy says:

The present change is a bug fix for AVB link iteratively up/down.

Steps to reproduce:
- start AVB TX stream (Using aplay via MSE),
- disconnect+reconnect the eth cable,
- after a reconnection the eth connection goes iteratively up/down
  without user interaction,
- this may heal after some seconds or even stay for minutes.

As the documentation specifies, the "renesas,no-ether-link" option
should be used when a board does not provide a proper AVB_LINK signal.
There is no need for this option enabled on RCAR H3/M3 Salvator-X/XS
and ULCB starter kits since the AVB_LINK is correctly handled by HW.

Choosing to keep or remove the "renesas,no-ether-link" option will
have impact on the code flow in the following ways:
- keeping this option enabled may lead to unexpected behavior since
  the RX & TX are enabled/disabled directly from adjust_link function
  without any HW interrogation,
- removing this option, the RX & TX will only be enabled/disabled after
  HW interrogation. The HW check is made through the LMON pin in PSR
  register which specifies AVB_LINK signal value (0 - at low level;
  1 - at high level).

In conclusion, the change is also a safety improvement because it
removes the "renesas,no-ether-link" option leading to a proper way
of detecting the link state based on HW interrogation and not on
software heuristic.

Note that DTS files for V3M Starter Kit, Draak and Eagle boards
contain the same property, the files are untouched due to unavailable
schematics to verify if the fix applies to these boards as well.

* tag 'renesas-fixes-for-v4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  arm64: dts: renesas: ulcb: Remove renesas, no-ether-link property
  arm64: dts: renesas: salvator-x: Remove renesas, no-ether-link property

The present change is a bug fix for AVB link iteratively up/down.

Steps to reproduce:
- start AVB TX stream (Using aplay via MSE),
- disconnect+reconnect the eth cable,
- after a reconnection the eth connection goes iteratively up/down
  without user interaction,
- this may heal after some seconds or even stay for minutes.

As the documentation specifies, the "renesas,no-ether-link" option
should be used when a board does not provide a proper AVB_LINK signal.
There is no need for this option enabled on RCAR H3/M3 Salvator-X/XS
and ULCB starter kits since the AVB_LINK is correctly handled by HW.

Choosing to keep or remove the "renesas,no-ether-link" option will
have impact on the code flow in the following ways:
- keeping this option enabled may lead to unexpected behavior since
  the RX & TX are enabled/disabled directly from adjust_link function
  without any HW interrogation,
- removing this option, the RX & TX will only be enabled/disabled after
  HW interrogation. The HW check is made through the LMON pin in PSR
  register which specifies AVB_LINK signal value (0 - at low level;
  1 - at high level).

In conclusion, the present change is also a safety improvement because
it removes the "renesas,no-ether-link" option leading to a proper way
of detecting the link state based on HW interrogation and not on
software heuristic.

Fixes: dc36965a8905 ("arm64: dts: r8a7796: salvator-x: Enable EthernetAVB")
Fixes: 6fa501c549aa ("arm64: dts: r8a7795: enable EthernetAVB on Salvator-X")
Signed-off-by: Bogdan Mirea <Bogdan-Stefan_Mirea@mentor.com>
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The present change is a bug fix for AVB link iteratively up/down.

Steps to reproduce:
- start AVB TX stream (Using aplay via MSE),
- disconnect+reconnect the eth cable,
- after a reconnection the eth connection goes iteratively up/down
  without user interaction,
- this may heal after some seconds or even stay for minutes.

As the documentation specifies, the "renesas,no-ether-link" option
should be used when a board does not provide a proper AVB_LINK signal.
There is no need for this option enabled on RCAR H3/M3 Salvator-X/XS
and ULCB starter kits since the AVB_LINK is correctly handled by HW.

Choosing to keep or remove the "renesas,no-ether-link" option will
have impact on the code flow in the following ways:
- keeping this option enabled may lead to unexpected behavior since
  the RX & TX are enabled/disabled directly from adjust_link function
  without any HW interrogation,
- removing this option, the RX & TX will only be enabled/disabled after
  HW interrogation. The HW check is made through the LMON pin in PSR
  register which specifies AVB_LINK signal value (0 - at low level;
  1 - at high level).

In conclusion, the present change is also a safety improvement because
it removes the "renesas,no-ether-link" option leading to a proper way
of detecting the link state based on HW interrogation and not on
software heuristic.

Fixes: dc36965a8905 ("arm64: dts: r8a7796: salvator-x: Enable EthernetAVB")
Fixes: 6fa501c549aa ("arm64: dts: r8a7795: enable EthernetAVB on Salvator-X")
Signed-off-by: Bogdan Mirea <Bogdan-Stefan_Mirea@mentor.com>
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Pull "Rockchip dts64 fixes for 4.15" from Heiko Stübner:

Another trailing interrupt-cell 0 removed.

Removed as well got the vdd_log regulator from the rk3399-puma board.
While it is there, the absence of any user makes it prone to configuration
problems when the pwm-regulator takes over the boot-up default and wiggles
settings there. Case in question was the PCIe host not working anymore.
With vdd_log removed for the time being, PCIe on Puma works again.

And a second stopgap is limiting the speed of the gmac on the rk3328-rock64
to 100MBit. While the hardware can reach 1GBit, currently it is not stable.
Limiting it to 100MBit for the time being allows nfsroots to be used again
until the problem is identified.

* tag 'v4.15-rockchip-dts64fixes-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  arm64: dts: rockchip: limit rk3328-rock64 gmac speed to 100MBit for now
  arm64: dts: rockchip: remove vdd_log from rk3399-puma
  arm64: dts: rockchip: fix trailing 0 in rk3328 tsadc interrupts

Amlogic fixes for v4.15-rc
- GPIO interrupt fixes
- socinfo fix for GX series
- fix typo

* tag 'amlogic-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM64: dts: meson-gx: fix UART pclk clock name
  meson-gx-socinfo: Fix package id parsing
  ARM: meson: fix spelling mistake: "Couln't" -> "Couldn't"
  ARM: dts: meson: fix the memory region of the GPIO interrupt controller
  ARM: dts: meson: correct the sort order for the the gpio_intc node

Signed-off-by: Olof Johansson <olof@lixom.net>