From Shawn Guo: i.MX SoC changes for 3.14: - Add the initial i.MX50 SoC support - Support device tree boot for i.MX35 - Move imx5 clock driver to use macros for clock ID - Some random updates and non-critical fixes on clock drivers - A few defconfig updates and minor cleanups * tag 'imx-soc-3.14' of git://git.linaro.org/people/shawnguo/linux-2.6: (37 commits) ARM: imx: improve the comment of CCM lpm SW workaround ARM: imx: improve status check of clock gate ARM: imx: add necessary interface for pfd ARM: imx_v6_v7_defconfig: Select CONFIG_REGULATOR_PFUZE100 ARM: imx_v6_v7_defconfig: Select MX35 and MX50 device tree support ARM: imx: Add cpu frequency scaling support ARM i.MX35: Add devicetree support. ARM: imx: update imx_v6_v7_defconfig ARM: imx6sl: Add missing spba clock to clock tree ARM: imx6sl: Add missing pll4_audio_div to the clock tree ARM: imx6: Derive spdif clock from pll3_pfd3_454m ARM: imx: use __initconst for const init definition ARM i.MX5: fix obvious typo in ldb_di0_gate clk definition ARM i.MX5: set CAN peripheral clock to 24 MHz parent ARM: imx: pllv1: Fix PLL calculation for i.MX27 ARM i.MX5: fix "shift" value for lp_apm_sel on i.MX50 and i.MX53 ARM: imx: imx53: Add SATA PHY clock ARM: imx_v6_v7_defconfig: Enable STMPE touchscreen ARM: imx: rename IMX6SL_CLK_CLK_END to IMX6SL_CLK_END ARM: imx: select PINCTRL at sub-architecure level ... Signed-off-by: Olof Johansson <olof@lixom.net>
Add appropriate UART address definitions and support defines for using the UARTs of the Freescale IMX50 SoC as debug ports. Signed-off-by: Greg Ungerer <gerg@uclinux.org> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Stop writing to the UART clock divider registers in the Tegra DEBUG_LL code. This allows the DEBUG_LL output to use whatever baud rate was set up by the bootloader. Some users are using higher rates than 115200. This removes the only usage of tegra_uart_config[3], so reduce the size allocated for that array. Finally, fix busyuart() so that it only waits for THRE and not TEMT. For some reason, TEMT doesn't get asserted (at least on Tegra30 Beaver) at 9600 baud, even though it does at 115200 baud. This sounds like a HW bug, but I haven't investigated. For reference, U-Boot's serial code has always only checked THRE, and not checked TEMT. Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Paul Walmsley <pwalmsley@nvidia.com> Reviewed-by: Thierry Reding <treding@nvidia.com>
The DEBUG_LL UART address is mapped as an MMU section, hence, the virtual address must be section-aligned. Sections are 1MB without LPAE and 2MB with LPAE. Tegra's virtual address was only aligned to 1MB, and hence the mapping was set up incorrectly with LPAE enabled, thus causing a hang early during boot. Fix this by picking a different virtual address that is aligned to 2MB. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Thierry Reding <treding@nvidia.com>
Pull ARM updates from Russell King:
"Included in this series are:
1. BE8 (modern big endian) changes for ARM from Ben Dooks
2. big.Little support from Nicolas Pitre and Dave Martin
3. support for LPAE systems with all system memory above 4GB
4. Perf updates from Will Deacon
5. Additional prefetching and other performance improvements from Will.
6. Neon-optimised AES implementation fro Ard.
7. A number of smaller fixes scattered around the place.
There is a rather horrid merge conflict in tools/perf - I was never
notified of the conflict because it originally occurred between Will's
tree and other stuff. Consequently I have a resolution which Will
forwarded me, which I'll forward on immediately after sending this
mail.
The other notable thing is I'm expecting some build breakage in the
crypto stuff on ARM only with Ard's AES patches. These were merged
into a stable git branch which others had already pulled, so there's
little I can do about this. The problem is caused because these
patches have a dependency on some code in the crypto git tree - I
tried requesting a branch I can pull to resolve these, and all I got
each time from the crypto people was "we'll revert our patches then"
which would only make things worse since I still don't have the
dependent patches. I've no idea what's going on there or how to
resolve that, and since I can't split these patches from the rest of
this pull request, I'm rather stuck with pushing this as-is or
reverting Ard's patches.
Since it should "come out in the wash" I've left them in - the only
build problems they seem to cause at the moment are with randconfigs,
and since it's a new feature anyway. However, if by -rc1 the
dependencies aren't in, I think it'd be best to revert Ard's patches"
I resolved the perf conflict roughly as per the patch sent by Russell,
but there may be some differences. Any errors are likely mine. Let's
see how the crypto issues work out..
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (110 commits)
ARM: 7868/1: arm/arm64: remove atomic_clear_mask() in "include/asm/atomic.h"
ARM: 7867/1: include: asm: use 'int' instead of 'unsigned long' for 'oldval' in atomic_cmpxchg().
ARM: 7866/1: include: asm: use 'long long' instead of 'u64' within atomic.h
ARM: 7871/1: amba: Extend number of IRQS
ARM: 7887/1: Don't smp_cross_call() on UP devices in arch_irq_work_raise()
ARM: 7872/1: Support arch_irq_work_raise() via self IPIs
ARM: 7880/1: Clear the IT state independent of the Thumb-2 mode
ARM: 7878/1: nommu: Implement dummy early_paging_init()
ARM: 7876/1: clear Thumb-2 IT state on exception handling
ARM: 7874/2: bL_switcher: Remove cpu_hotplug_driver_{lock,unlock}()
ARM: footbridge: fix build warnings for netwinder
ARM: 7873/1: vfp: clear vfp_current_hw_state for dying cpu
ARM: fix misplaced arch_virt_to_idmap()
ARM: 7848/1: mcpm: Implement cpu_kill() to synchronise on powerdown
ARM: 7847/1: mcpm: Factor out logical-to-physical CPU translation
ARM: 7869/1: remove unused XSCALE_PMU Kconfig param
ARM: 7864/1: Handle 64-bit memory in case of 32-bit phys_addr_t
ARM: 7863/1: Let arm_add_memory() always use 64-bit arguments
ARM: 7862/1: pcpu: replace __get_cpu_var_uses
ARM: 7861/1: cacheflush: consolidate single-CPU ARMv7 cache disabling code
...
Conflicts: arch/arm/include/asm/atomic.h arch/arm/include/asm/hardirq.h arch/arm/kernel/smp.c
Add debug uart support for MSM8974. This patch adds a Kconfig entry and the base address for the debug uart. Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This implements output of debug messages on efm32 SoCs. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add low-level debug support for vybrid, so that earlyprintk can be enabled for debugging early boot issue. Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The PL01X debug code needs to take into account which endian mode the processor is running in. If it is big-endian, ensure the data is swapped appropriately. Note, we could do this slightly more efficiently if we have an macro to do the necessary swap for the bits used by test. Reviewed-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>