i.MX fixes for 6.9, round 2:

- Fix i.MX8MP the second CSI2 assigned-clock property which got wrong by
  commit f78835d1e616 ("arm64: dts: imx8mp: reparent MEDIA_MIPI_PHY1_REF
  to CLK_24M")
- Correct USB over-current polarity for imx6ull-tarragon board

* tag 'imx-fixes-6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: dts: imx6ull-tarragon: fix USB over-current polarity
  arm64: dts: imx8mp: Fix assigned-clocks for second CSI2

Link: https://lore.kernel.org/r/ZioopqscxwUOwQkf@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

AT91 fixes for 6.9

It contains:
- fixes for regulator nodes on SAMA7G5 based boards: proper DT property is used
  to setup regulators suspend voltage.

* tag 'at91-fixes-6.9' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
  ARM: dts: microchip: at91-sama7g54_curiosity: Replace regulator-suspend-voltage with the valid property
  ARM: dts: microchip: at91-sama7g5ek: Replace regulator-suspend-voltage with the valid property

Link: https://lore.kernel.org/r/20240421124824.960096-1-claudiu.beznea@tuxon.dev
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Our Tarragon platform uses a active-low signal to inform
the i.MX6ULL about the over-current detection.

Fixes: 5e4f393ccbf0 ("ARM: dts: imx6ull: Add chargebyte Tarragon support")
Signed-off-by: Michael Heimpold <michael.heimpold@chargebyte.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

By checking the pmic node with microchip,mcp16502.yaml#
'regulator-suspend-voltage' does not match any of the
regexes 'pinctrl-[0-9]+' from schema microchip,mcp16502.yaml#
which inherits regulator.yaml#. So replace regulator-suspend-voltage
with regulator-suspend-microvolt to avoid the inconsitency.

Fixes: ebd6591f8ddb ("ARM: dts: microchip: sama7g54_curiosity: Add initial device tree of the board")
Signed-off-by: Andrei Simion <andrei.simion@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20240404123824.19182-3-andrei.simion@microchip.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>

By checking the pmic node with microchip,mcp16502.yaml#
'regulator-suspend-voltage' does not match any of the
regexes 'pinctrl-[0-9]+' from schema microchip,mcp16502.yaml#
which inherits regulator.yaml#. So replace regulator-suspend-voltage
with regulator-suspend-microvolt to avoid the inconsitency.

Fixes: 85b1304b9daa ("ARM: dts: at91: sama7g5ek: set regulator voltages for standby state")
Signed-off-by: Andrei Simion <andrei.simion@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20240404123824.19182-2-andrei.simion@microchip.com
[claudiu.beznea: added a dot before starting the last sentence in commit
 description]
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>

Since commit 63b0cd30b78e ("media: ov2680: Add bus-cfg / endpoint
property verification") the ov2680 no longer probes on a imx7s-warp7:

ov2680 1-0036: error -EINVAL: supported link freq 330000000 not found
ov2680 1-0036: probe with driver ov2680 failed with error -22

Fix it by passing the required 'link-frequencies' property as
recommended by:

https://www.kernel.org/doc/html/v6.9-rc1/driver-api/media/camera-sensor.html#handling-clocks

Cc: stable@vger.kernel.org
Fixes: 63b0cd30b78e ("media: ov2680: Add bus-cfg / endpoint property verification")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

'no-emmc' is not a valid property.

The original intention was to use the 'no-mmc' property.

Change it accordingly to fix the following dt-schema warning:

imx7s-mba7.dtb: mmc@30b40000: Unevaluated properties are not allowed ('no-emmc' was unexpected)

Fixes: d430a7e0e181 ("ARM: dts: imx7-mba7: restrict usdhc interface modes")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pull more ARM SoC updates from Arnd Bergmann:
 "These are changes that for some reason ended up not making it into the
  first four branches but that should still make it into 6.9:

   - A rework of the omap clock support that touches both drivers and
     device tree files

   - The reset controller branch changes that had a dependency on late
     bugfixes. Merging them here avoids a backmerge of 6.8-rc5 into the
     drivers branch

   - The RISC-V/starfive, RISC-V/microchip and ARM/Broadcom devicetree
     changes that got delayed and needed some extra time in linux-next
     for wider testing"

* tag 'soc-late-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (31 commits)
  soc: fsl: dpio: fix kcalloc() argument order
  bus: ts-nbus: Improve error reporting
  bus: ts-nbus: Convert to atomic pwm API
  riscv: dts: starfive: jh7110: Add camera subsystem nodes
  ARM: bcm: stop selecing CONFIG_TICK_ONESHOT
  ARM: dts: omap3: Update clksel clocks to use reg instead of ti,bit-shift
  ARM: dts: am3: Update clksel clocks to use reg instead of ti,bit-shift
  clk: ti: Improve clksel clock bit parsing for reg property
  clk: ti: Handle possible address in the node name
  dt-bindings: pwm: opencores: Add compatible for StarFive JH8100
  dt-bindings: riscv: cpus: reg matches hart ID
  reset: Instantiate reset GPIO controller for shared reset-gpios
  reset: gpio: Add GPIO-based reset controller
  cpufreq: do not open-code of_phandle_args_equal()
  of: Add of_phandle_args_equal() helper
  reset: simple: add support for Sophgo SG2042
  dt-bindings: reset: sophgo: support SG2042
  riscv: dts: microchip: add specific compatible for mpfs pdma
  riscv: dts: microchip: add missing CAN bus clocks
  ARM: brcmstb: Add debug UART entry for 74165
  ...

Pull MTD updates from Miquel Raynal:
 "MTD:

   - The Carillo Ranch driver has been removed

   - Top level mtd bindings have received a couple of improvements
     (references, selects)

   - The ssfdc driver received few minor adjustments

   - The usual load of misc/small improvements and fixes

  Raw NAND:

   - The main series brought is an update of the Broadcom support to
     support all BCMBCA SoCs and their specificity (ECC, write
     protection, configuration straps), plus a few misc fixes and
     changes in the main driver. Device tree updates are also part of
     this PR, initially because of a misunderstanding on my side.

   - The STM32_FMC2 controller driver is also upgraded to properly
     support MP1 and MP25 SoCs.

   - A new compatible is added for an Atmel flavor.

   - Among all these feature changes, there is as well a load of
     continuous read related fixes, avoiding more corner conditions and
     clarifying the logic. Finally a few miscellaneous fixes are made to
     the core, the lpx32xx_mlc, fsl_lbc, Meson and Atmel controller
     driver, as well as final one in the Hynix vendor driver.

  SPI-NAND:

   - The ESMT support has been extended to match 5 bytes ID to avoid
     collisions. Winbond support on its side receives support for
     W25N04KV chips.

  SPI NOR:

   - SPI NOR gets the non uniform erase code cleaned. We stopped using
     bitmasks for erase types and flags, and instead introduced
     dedicated members. We then passed the SPI NOR erase map to MTD.
     Users can now determine the erase regions and make informed
     decisions on partitions size.

   - An optional interrupt property is now described in the bindings"

* tag 'mtd/for-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (50 commits)
  mtd: rawnand: Ensure continuous reads are well disabled
  mtd: rawnand: Constrain even more when continuous reads are enabled
  mtd: rawnand: brcmnand: Add support for getting ecc setting from strap
  mtd: rawnand: brcmnand: fix sparse warnings
  mtd: nand: raw: atmel: Fix comment in timings preparation
  mtd: rawnand: Ensure all continuous terms are always in sync
  mtd: rawnand: Add a helper for calculating a page index
  mtd: rawnand: Fix and simplify again the continuous read derivations
  mtd: rawnand: hynix: remove @nand_technology kernel-doc description
  dt-bindings: atmel-nand: add microchip,sam9x7-pmecc
  mtd: rawnand: brcmnand: Support write protection setting from dts
  mtd: rawnand: brcmnand: Add BCMBCA read data bus interface
  mtd: rawnand: brcmnand: Rename bcm63138 nand driver
  arm64: dts: broadcom: bcmbca: Update router boards
  arm64: dts: broadcom: bcmbca: Add NAND controller node
  ARM: dts: broadcom: bcmbca: Add NAND controller node
  mtd: spi-nor: core: correct type of i
  mtd: spi-nor: core: set mtd->eraseregions for non-uniform erase map
  mtd: spi-nor: core: get rid of SNOR_OVERLAID_REGION flag
  mtd: spi-nor: core: get rid of SNOR_LAST_REGION flag
  ...

Add support for Broadcom STB NAND controller in BCMBCA ARMv7 chip dts
files.

Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: David Regan <dregan@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/linux-mtd/20240223034758.13753-8-william.zhang@broadcom.com