The check_spi_bus_bridge() in scripts/dtc/checks.c requires that the node
have "spi-slave" property must with "#address-cells = <0>" and
"#size-cells = <0>". But currently both "#address-cells" and "#size-cells"
properties are deleted, the corresponding default values are 2 and 1. As a
result, the check fails and below warnings is displayed.

arch/arm/boot/dts/mmp2.dtsi:472.23-480.6: Warning (spi_bus_bridge): \
/soc/apb@d4000000/spi@d4037000: incorrect #address-cells for SPI bus
  also defined at arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts:225.7-237.3
arch/arm/boot/dts/mmp2.dtsi:472.23-480.6: Warning (spi_bus_bridge): \
/soc/apb@d4000000/spi@d4037000: incorrect #size-cells for SPI bus
  also defined at arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts:225.7-237.3
arch/arm/boot/dts/mmp2-olpc-xo-1-75.dtb: Warning (spi_bus_reg): \
Failed prerequisite 'spi_bus_bridge'

Because the value of "#size-cells" is already defined as zero in the node
"ssp3: spi@d4037000" in arch/arm/boot/dts/mmp2.dtsi. So we only need to
explicitly add "#address-cells = <0>" and keep "#size-cells" no change.

Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20201207084752.1665-2-thunder.leizhen@huawei.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

i.MX fixes for 5.10, round 5:

- Fix a regression on SoC revision detection with ANATOP, that is
  introduced by commit  4a4fb66119eb ("ARM: imx: Add missing
  of_node_put()").
- Drop PAD_GPIO_6 from imx6qdl-wandboard ENET pin group, as the pin is
  used by camera sensor now.
- Fix I2C3_SCL pinmux on imx6qdl-kontron-samx6i board, so that SoM EEPROM
  can be accessed.

* tag 'imx-fixes-5.10-5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: dts: imx6qdl-kontron-samx6i: fix I2C_PM scl pin
  ARM: dts: imx6qdl-wandboard-revd1: Remove PAD_GPIO_6 from enetgrp
  ARM: imx: Use correct SRC base address

Link: https://lore.kernel.org/r/20201201091820.GW4072@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

A few more RGMII-ID fixes, and a bunch of other more random fixes

* tag 'sunxi-fixes-for-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  ARM: dts: sun7i: pcduino3-nano: enable RGMII RX/TX delay on PHY
  ARM: dts: sun8i: v3s: fix GIC node memory range
  ARM: dts: sun8i: v40: bananapi-m2-berry: Fix ethernet node
  ARM: dts: sun8i: r40: bananapi-m2-berry: Fix dcdc1 regulator
  ARM: dts: sun7i: bananapi: Enable RGMII RX/TX delay on Ethernet PHY
  ARM: dts: s3: pinecube: align compatible property to other S3 boards
  ARM: sunxi: Add machine match for the Allwinner V3 SoC
  arm64: dts: allwinner: h6: orangepi-one-plus: Fix ethernet

Link: https://lore.kernel.org/r/1280f1de-1b6d-4cc2-8448-e5a9096a41e8.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Pull Kbuild fixes from Masahiro Yamada:

 - Move -Wcast-align to W=3, which tends to be false-positive and there
   is no tree-wide solution.

 - Pass -fmacro-prefix-map to KBUILD_CPPFLAGS because it is a
   preprocessor option and makes sense for .S files as well.

 - Disable -gdwarf-2 for Clang's integrated assembler to avoid warnings.

 - Disable --orphan-handling=warn for LLD 10.0.1 to avoid warnings.

 - Fix undesirable line breaks in *.mod files.

* tag 'kbuild-fixes-v5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: avoid split lines in .mod files
  kbuild: Disable CONFIG_LD_ORPHAN_WARN for ld.lld 10.0.1
  kbuild: Hoist '--orphan-handling' into Kconfig
  Kbuild: do not emit debug info for assembly with LLVM_IAS=1
  kbuild: use -fmacro-prefix-map for .S sources
  Makefile.extrawarn: move -Wcast-align to W=3

Currently, '--orphan-handling=warn' is spread out across four different
architectures in their respective Makefiles, which makes it a little
unruly to deal with in case it needs to be disabled for a specific
linker version (in this case, ld.lld 10.0.1).

To make it easier to control this, hoist this warning into Kconfig and
the main Makefile so that disabling it is simpler, as the warning will
only be enabled in a couple places (main Makefile and a couple of
compressed boot folders that blow away LDFLAGS_vmlinx) and making it
conditional is easier due to Kconfig syntax. One small additional
benefit of this is saving a call to ld-option on incremental builds
because we will have already evaluated it for CONFIG_LD_ORPHAN_WARN.

To keep the list of supported architectures the same, introduce
CONFIG_ARCH_WANT_LD_ORPHAN_WARN, which an architecture can select to
gain this automatically after all of the sections are specified and size
asserted. A special thanks to Kees Cook for the help text on this
config.

Link: https://github.com/ClangBuiltLinux/linux/issues/1187
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

Use the correct pin for the i2c scl signal else we can't access the
SoM eeprom.

Fixes: 2a51f9dae13d ("ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module")
Signed-off-by: Bernd Bauer <bernd.bauer@anton-paar.com>
[m.felsch@pengutronix.de: Adapt commit message]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Since commit 8ad2d1dcce54 ("ARM: dts: imx6qdl-wandboard: Add OV5645 camera
support") the PAD_GPIO_6 is used for providing the camera sensor clock.

Remove it from the enetgrp to fix the following IOMXU conflict:

[    9.972414] imx6q-pinctrl 20e0000.pinctrl: pin MX6Q_PAD_GPIO_6 already requested by 2188000.ethernet; cannot claim for 1-003c
[    9.983857] imx6q-pinctrl 20e0000.pinctrl: pin-140 (1-003c) status -22
[    9.990514] imx6q-pinctrl 20e0000.pinctrl: could not request pin 140 (MX6Q_PAD_GPIO_6) from group ov5645grp  on device 20e0000.pinctrl

Fixes: 8ad2d1dcce54 ("ARM: dts: imx6qdl-wandboard: Add OV5645 camera support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pull ARM SoC fixes from Arnd Bergmann:
 "Another set of patches for devicetree files and Arm SoC specific
  drivers:

   - A fix for OP-TEE shared memory on non-SMP systems

   - multiple code fixes for the OMAP platform, including one regression
     for the CPSW network driver and a few runtime warning fixes

   - Some DT patches for the Rockchip RK3399 platform, in particular
     fixing the MMC device ordering that recently became
     nondeterministic with async probe.

   - Multiple DT fixes for the Tegra platform, including a regression
     fix for suspend/resume on TX2

   - A regression fix for a user-triggered fault in the NXP dpio driver

   - A regression fix for a bug caused by an earlier bug fix in the
     xilinx firmware driver

   - Two more DTC warning fixes

   - Sylvain Lemieux steps down as maintainer for the NXP LPC32xx
     platform"

* tag 'arm-soc-fixes-v5.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (24 commits)
  arm64: tegra: Fix Tegra234 VDK node names
  arm64: tegra: Wrong AON HSP reg property size
  arm64: tegra: Fix USB_VBUS_EN0 regulator on Jetson TX1
  arm64: tegra: Correct the UART for Jetson Xavier NX
  arm64: tegra: Disable the ACONNECT for Jetson TX2
  optee: add writeback to valid memory type
  firmware: xilinx: Use hash-table for api feature check
  firmware: xilinx: Fix SD DLL node reset issue
  soc: fsl: dpio: Get the cpumask through cpumask_of(cpu)
  ARM: dts: dra76x: m_can: fix order of clocks
  bus: ti-sysc: suppress err msg for timers used as clockevent/source
  MAINTAINERS: Remove myself as LPC32xx maintainers
  arm64: dts: qcom: clear the warnings caused by empty dma-ranges
  arm64: dts: broadcom: clear the warnings caused by empty dma-ranges
  ARM: dts: am437x-l4: fix compatible for cpsw switch dt node
  arm64: dts: rockchip: Reorder LED triggers from mmc devices on rk3399-roc-pc.
  arm64: dts: rockchip: Assign a fixed index to mmc devices on rk3399 boards.
  arm64: dts: rockchip: Remove system-power-controller from pmic on Odroid Go Advance
  arm64: dts: rockchip: fix NanoPi R2S GMAC clock name
  ARM: OMAP2+: Manage MPU state properly for omap_enter_idle_coupled()
  ...

Fixes for omaps for various issues noticed during the -rc cycle:

- Earlier omap4 cpuidle fix was incomplete and needs to use a
  configured idle state instead

- Fix am4 cpsw driver compatible to avoid invalid resource error
  for the legacy driver

- Two kconfig fixes for genpd support that we added for for v5.10
  for proper location of the option and adding missing option

- Fix ti-sysc reset status checking on enabling modules to ignore
  quirky modules with reset status only usable when the quirk is
  activated during reset. Also fix bogus resetdone warning for
  cpsw and modules with no sysst register reset status bit

- Suppress a ti-sysc warning for timers reserved as system timers

- Fix the ordering of clocks for dra7 m_can

* tag 'omap-for-v5.10/fixes-rc5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: dra76x: m_can: fix order of clocks
  bus: ti-sysc: suppress err msg for timers used as clockevent/source
  ARM: dts: am437x-l4: fix compatible for cpsw switch dt node
  ARM: OMAP2+: Manage MPU state properly for omap_enter_idle_coupled()
  bus: ti-sysc: Fix bogus resetdone warning on enable for cpsw
  bus: ti-sysc: Fix reset status check for modules with quirks
  ARM: OMAP2+: Fix missing select PM_GENERIC_DOMAINS_OF
  ARM: OMAP2+: Fix location for select PM_GENERIC_DOMAINS

Link: https://lore.kernel.org/r/pull-1606460270-864284@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The RX/TX delays for the Ethernet PHY on the Linksprite pcDuino 3 Nano
are configured in hardware, using resistors that are populated to pull
the RTL8211E's RXDLY/TXDLY pins low or high as needed.

phy-mode should be set to rgmii-id to reflect this. Previously it was
set to rgmii, which used to work but now results in the delays being
disabled again as a result of the bugfix in commit bbc4d71d6354 ("net:
phy: realtek: fix rtl8211e rx/tx delay config").

Tested on two pcDuino 3 Nano boards purchased in 2015. Without this fix,
Ethernet works unreliably on one board and doesn't work at all on the
other.

Fixes: 061035d456c9 ("ARM: dts: sun7i: Add dts file for pcDuino 3 Nano board")
Signed-off-by: Adam Sampson <ats@offog.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201123174739.6809-1-ats@offog.org