mvebu fixes for 5.0

They are all device tree fixes which also worth being in stable:

 - Reserve PSCI area on Armada 7K/8K preventing the kernel accessing
   this area and crashing while doing it.

 - Use correct PCIe reset signal on MACCHIATOBin  (Armada 8040 based)

 - Fix polarity of GPIO fan line D-Link DNS NASes(kikwood based)

* tag 'mvebu-fixes-5.0-1' of git://git.infradead.org/linux-mvebu:
  ARM: dts: kirkwood: Fix polarity of GPIO fan lines
  arm64: dts: marvell: mcbin: fix PCIe reset signal
  arm64: dts: marvell: armada-ap806: reserve PSCI area

Signed-off-by: Olof Johansson <olof@lixom.net>

These two lines are active high, not active low. The bug was
found when we changed the kernel to respect the polarity defined
in the device tree.

Fixes: 1b90e06b1429 ("ARM: kirkwood: Use devicetree to define DNS-32[05] fan")
Cc: Jamie Lentin <jm@lentin.co.uk>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Julien D'Ascenzio <jdascenzio@posteo.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Reported-by: Julien D'Ascenzio <jdascenzio@posteo.net>
Tested-by: Julien D'Ascenzio <jdascenzio@posteo.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

To avoid  the following error:
asoc-simple-card sound: ASoC: Failed to create card debugfs directory

Which is because the card name contains '/' character, which can not be
used in file or directory names.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

Add the board level fixed regulators for 3.3V and 1.8V which is used to
power - among other things - the tlv320aic3106 codec.

Apart from removing the following warning during boot:
tlv320aic3x-codec 0-0018: Invalid supply voltage(s) AVDD: -22, DVDD: -22

With the correct voltages the driver can select correct OCMV value to
reduce pop noise.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

To avoid  the following error:
asoc-simple-card sound: ASoC: Failed to create card debugfs directory

Which is because the card name contains '/' character, which can not be
used in file or directory names.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

Add the board level fixed regulators for 3.3V and 1.8V which is used to
power - among other things - the tlv320aic3106 codec.

Apart from removing the following warning during boot:
tlv320aic3x-codec 0-0018: Too high supply voltage(s) AVDD: 5000000, DVDD: 5000000

With the correct voltages the driver can select correct OCMV value to
reduce pop noise.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

Pull more Kbuild updates from Masahiro Yamada:

 - improve boolinit.cocci and use_after_iter.cocci semantic patches

 - fix alignment for kallsyms

 - move 'asm goto' compiler test to Kconfig and clean up jump_label
   CONFIG option

 - generate asm-generic wrappers automatically if arch does not
   implement mandatory UAPI headers

 - remove redundant generic-y defines

 - misc cleanups

* tag 'kbuild-v4.21-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kconfig: rename generated .*conf-cfg to *conf-cfg
  kbuild: remove unnecessary stubs for archheader and archscripts
  kbuild: use assignment instead of define ... endef for filechk_* rules
  arch: remove redundant UAPI generic-y defines
  kbuild: generate asm-generic wrappers if mandatory headers are missing
  arch: remove stale comments "UAPI Header export list"
  riscv: remove redundant kernel-space generic-y
  kbuild: change filechk to surround the given command with { }
  kbuild: remove redundant target cleaning on failure
  kbuild: clean up rule_dtc_dt_yaml
  kbuild: remove UIMAGE_IN and UIMAGE_OUT
  jump_label: move 'asm goto' support test to Kconfig
  kallsyms: lower alignment on ARM
  scripts: coccinelle: boolinit: drop warnings on named constants
  scripts: coccinelle: check for redeclaration
  kconfig: remove unused "file" field of yylval union
  nds32: remove redundant kernel-space generic-y
  nios2: remove unneeded HAS_DMA define

Pull PCI updates from Bjorn Helgaas:

 - Remove unused lists from ASPM pcie_link_state (Frederick Lawler)

 - Fix Broadcom CNB20LE host bridge unintended sign extension (Colin Ian
   King)

 - Expand Kconfig "PF" acronyms (Randy Dunlap)

 - Update MAINTAINERS for arch/x86/kernel/early-quirks.c (Bjorn Helgaas)

 - Add missing include to drivers/pci.h (Alexandru Gagniuc)

 - Override Synopsys USB 3.x HAPS device class so dwc3-haps can claim it
   instead of xhci (Thinh Nguyen)

 - Clean up P2PDMA documentation (Randy Dunlap)

 - Allow runtime PM even if driver doesn't supply callbacks (Jarkko
   Nikula)

 - Remove status check after submitting Switchtec MRPC Firmware Download
   commands to avoid Completion Timeouts (Kelvin Cao)

 - Set Switchtec coherent DMA mask to allow 64-bit DMA (Boris Glimcher)

 - Fix Switchtec SWITCHTEC_IOCTL_EVENT_IDX_ALL flag overwrite issue
   (Joey Zhang)

 - Enable write combining for Switchtec MRPC Input buffers (Kelvin Cao)

 - Add Switchtec MRPC DMA mode support (Wesley Sheng)

 - Skip VF scanning on powerpc, which does this in firmware (Sebastian
   Ott)

 - Add Amlogic Meson PCIe controller driver and DT bindings (Yue Wang)

 - Constify histb dw_pcie_host_ops structure (Julia Lawall)

 - Support multiple power domains for imx6 (Leonard Crestez)

 - Constify layerscape driver data (Stefan Agner)

 - Update imx6 Kconfig to allow imx6 PCIe in imx7 kernel (Trent Piepho)

 - Support armada8k GPIO reset (Baruch Siach)

 - Support suspend/resume support on imx6 (Leonard Crestez)

 - Don't hard-code DesignWare DBI/ATU offst (Stephen Warren)

 - Skip i.MX6 PHY setup on i.MX7D (Andrey Smirnov)

 - Remove Jianguo Sun from HiSilicon STB maintainers (Lorenzo Pieralisi)

 - Mask DesignWare interrupts instead of disabling them to avoid lost
   interrupts (Marc Zyngier)

 - Add locking when acking DesignWare interrupts (Marc Zyngier)

 - Ack DesignWare interrupts in the proper callbacks (Marc Zyngier)

 - Use devm resource parser in mediatek (Honghui Zhang)

 - Remove unused mediatek "num-lanes" DT property (Honghui Zhang)

 - Add UniPhier PCIe controller driver and DT bindings (Kunihiko
   Hayashi)

 - Enable MSI for imx6 downstream components (Richard Zhu)

* tag 'pci-v4.21-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (40 commits)
  PCI: imx: Enable MSI from downstream components
  s390/pci: skip VF scanning
  PCI/IOV: Add flag so platforms can skip VF scanning
  PCI/IOV: Factor out sriov_add_vfs()
  PCI: uniphier: Add UniPhier PCIe host controller support
  dt-bindings: PCI: Add UniPhier PCIe host controller description
  PCI: amlogic: Add the Amlogic Meson PCIe controller driver
  dt-bindings: PCI: meson: add DT bindings for Amlogic Meson PCIe controller
  arm64: dts: mt7622: Remove un-used property for PCIe
  arm: dts: mt7623: Remove un-used property for PCIe
  dt-bindings: PCI: MediaTek: Remove un-used property
  PCI: mediatek: Remove un-used variant in struct mtk_pcie_port
  MAINTAINERS: Remove Jianguo Sun from HiSilicon STB DWC entry
  PCI: dwc: Don't hard-code DBI/ATU offset
  PCI: imx: Add imx6sx suspend/resume support
  PCI: armada8k: Add support for gpio controlled reset signal
  PCI: dwc: Adjust Kconfig to allow IMX6 PCIe host on IMX7
  PCI: dwc: layerscape: Constify driver data
  PCI: imx: Add multi-pd support
  PCI: Override Synopsys USB 3.x HAPS device class
  ...

Since commit 9c2af1c7377a ("kbuild: add .DELETE_ON_ERROR special
target"), the target file is automatically deleted on failure.

The boilerplate code

  ... || { rm -f $@; false; }

is unneeded.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Pull more ARM SoC updates from Olof Johansson:
 "A few updates that we merged late but are low risk for regressions for
  other platforms (and a few other straggling patches):

   - I mis-tagged the 'drivers' branch, and missed 3 patches. Merged in
     here. They're for a driver for the PL353 SRAM controller and a
     build fix for the qualcomm scm driver.

   - A new platform, RDA Micro RDA8810PL (Cortex-A5 w/ integrated
     Vivante GPU, 256MB RAM, Wifi). This includes some acked
     platform-specific drivers (serial, etc). This also include DTs for
     two boards with this SoC, OrangePi 2G and OrangePi i86.

   - i.MX8 is another new platform (NXP, 4x Cortex-A53 + Cortex-M4, 4K
     video playback offload). This is the first i.MX 64-bit SoC.

   - Some minor updates to Samsung boards (adding a few peripherals in
     DTs).

   - Small rework for SMP bootup on STi platforms.

   - A couple of TEE driver fixes.

   - A couple of new config options (bcm2835 thermal, Uniphier MDMAC)
     enabled in defconfigs"

* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (27 commits)
  ARM: multi_v7_defconfig: enable CONFIG_UNIPHIER_MDMAC
  arm64: defconfig: Re-enable bcm2835-thermal driver
  MAINTAINERS: Add entry for RDA Micro SoC architecture
  tty: serial: Add RDA8810PL UART driver
  ARM: dts: rda8810pl: Add interrupt support for UART
  dt-bindings: serial: Document RDA Micro UART
  ARM: dts: rda8810pl: Add timer support
  ARM: dts: Add devicetree for OrangePi i96 board
  ARM: dts: Add devicetree for OrangePi 2G IoT board
  ARM: dts: Add devicetree for RDA8810PL SoC
  ARM: Prepare RDA8810PL SoC
  dt-bindings: arm: Document RDA8810PL and reference boards
  dt-bindings: Add RDA Micro vendor prefix
  ARM: sti: remove pen_release and boot_lock
  arm64: dts: exynos: Add Bluetooth chip to TM2(e) boards
  arm64: dts: imx8mq-evk: enable watchdog
  arm64: dts: imx8mq: add watchdog devices
  MAINTAINERS: add i.MX8 DT path to i.MX architecture
  arm64: add support for i.MX8M EVK board
  arm64: add basic DTS for i.MX8MQ
  ...