Arnd writes:
  "ARM: SoC fixes for 4.19

   Two last minute bugfixes, both for NXP platforms:

   * The Layerscape 'qbman' infrastructure suffers from probe ordering
     bugs in some configurations, a two-patch series adds a hotfix for
     this. 4.20 will have a longer set of patches to rework it.

   * The old imx53-qsb board regressed in 4.19 after the addition
     of cpufreq support, adding a set of explicit operating points
     fixes this."

* tag 'armsoc-fixes-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  soc: fsl: qman_portals: defer probe after qman's probe
  soc: fsl: qbman: add APIs to retrieve the probing status
  ARM: dts: imx53-qsb: disable 1.2GHz OPP

NXP/FSL SoC driver fixes for v4.19 round 2

- Fix crash of qman_portal by deferring its probe if qman is not probed

* tag 'soc-fsl-fix-v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
  soc: fsl: qman_portals: defer probe after qman's probe
  soc: fsl: qbman: add APIs to retrieve the probing status
  soc: fsl: qe: Fix copy/paste bug in ucc_get_tdm_sync_shift()
  soc: fsl: qbman: qman: avoid allocating from non existing gen_pool
  ARM: dts: BCM63xx: Fix incorrect interrupt specifiers
  MAINTAINERS: update the Annapurna Labs maintainer email
  ARM: dts: sun8i: drop A64 HDMI PHY fallback compatible from R40 DT
  ARM: dts: at91: sama5d2_ptc_ek: fix nand pinctrl

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

i.MX fixes for 4.19, round 2:
 - i.MX53 QSB board stops working when cpufreq driver is enabled,
   because the default OPP table has the maximum CPU frequency at
   1.2GHz, while the board is only capable of running 1GHz.  Fix up
   the OPP table for the board to get it work with cpufreq driver.

* tag 'imx-fixes-4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: dts: imx53-qsb: disable 1.2GHz OPP

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Olof writes:
  "ARM: SoC fixes

   A handful of fixes that have been coming in the last couple of weeks:

   - Freescale fixes for on-chip accellerators
   - A DT fix for stm32 to avoid fallback to non-DMA SPI mode
   - Fixes for badly specified interrupts on BCM63xx SoCs
   - Allwinner A64 HDMI was incorrectly specified as fully compatble with R40
   - Drive strength fix for SAMA5D2 NAND pins on one board"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: dts: stm32: update SPI6 dmas property on stm32mp157c
  soc: fsl: qe: Fix copy/paste bug in ucc_get_tdm_sync_shift()
  soc: fsl: qbman: qman: avoid allocating from non existing gen_pool
  ARM: dts: BCM63xx: Fix incorrect interrupt specifiers
  MAINTAINERS: update the Annapurna Labs maintainer email
  ARM: dts: sun8i: drop A64 HDMI PHY fallback compatible from R40 DT
  ARM: dts: at91: sama5d2_ptc_ek: fix nand pinctrl

Remove unused parameter from SPI6 dmas property on stm32mp157c SoC.

Fixes: dc3f8c86c10d ("ARM: dts: stm32: add SPI support on stm32mp157c")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
[olof: Without this patch, SPI6 will fall back to interrupt mode with
lower perfmance]
Signed-off-by: Olof Johansson <olof@lixom.net>

This pull request contains Broadcom ARM-based SoCs Device Tree changes
intended for 4.19, please pull the following:

- Florian fixes the PPI and SPI interrupts in the BCM63138 (DSL) SoC DTS

* tag 'arm-soc/for-4.19/devicetree-fixes' of https://github.com/Broadcom/stblinux:
  ARM: dts: BCM63xx: Fix incorrect interrupt specifiers

Signed-off-by: Olof Johansson <olof@lixom.net>

AT91 fixes for 4.19:

 - fix a NAND issue on sama5d2_ptc_ek (drive strength setting to fix
   corruption)

* tag 'at91-4.19-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
  ARM: dts: at91: sama5d2_ptc_ek: fix nand pinctrl

Signed-off-by: Olof Johansson <olof@lixom.net>

A number of our interrupts were incorrectly specified, fix both the PPI
and SPI interrupts to be correct.

Fixes: b5762cacc411 ("ARM: bcm63138: add NAND DT support")
Fixes: 46d4bca0445a ("ARM: BCM63XX: add BCM63138 minimal Device Tree")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Allwinner fixes - round 2

One additional fix regarding HDMI on the R40 SoC.

Based on preliminary tests and code dumps for the R40, it was thought
that the whole HDMI block was the same on the R40 and A64.

Recent tests regarding the A64 showed that this was not the case. The
HDMI PHY on the A64 only has one clock parent. How this occurs at the
hardware level is unclear, as Allwinner has not given any feedback on
this matter. Nevertheless it is clear that the hardware acts differently
between the A64 and R40 in such a way that the R40's HDMI PHY is not
backward compatible with the A64's. As such we need to drop the fallback
compatible string in the R40's device tree. This was added in v4.19-rc1.

* tag 'sunxi-fixes-for-4.19-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  ARM: dts: sun8i: drop A64 HDMI PHY fallback compatible from R40 DT

Signed-off-by: Olof Johansson <olof@lixom.net>

The R40 HDMI PHY seems to be different to the A64 one, the A64 one
has no input mux, but the R40 one has.

Drop the A64 fallback compatible from the HDMI PHY node in R40 DT.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[wens@csie.org: Fix subject prefix order]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>