linux.git/arch/arm/boot, branch v4.0-rc2

ARM: dts: am335x-bone*: usb0 is hardwired for peripheral

2015-02-24T18:35:44+00:00

Fixes: http://bugs.elinux.org/issues/127

the bb.org community was seeing random reboots before this change.

Signed-off-by: Robert Nelson 
Reviewed-by: Felipe Balbi 
Acked-by: Felipe Balbi 
Signed-off-by: Tony Lindgren

ARM: dts: dra7x-evm: beagle-x15: Fix USB Host

2015-02-24T18:35:43+00:00

In commit 87517d26d888 ("ARM: dts: dra7-evm: Add extcon nodes for USB")
we enabled Extcon USB gpio to tackle the USB ID pin and get
peripheral mode to work.

But the extcon-gpio-usb driver [1] didn't make it into v4.0
and this makes the USB driver defer probe indefinitely breaking
USB Host functionality.

As a temporary fix we remove the extcon handle from the
USB controller and add it back when the extcon driver
merges in v4.1.

[1] - https://lkml.org/lkml/2015/2/2/187

Signed-off-by: Roger Quadros 
Signed-off-by: Tony Lindgren

ARM: dts: dra7: Correct the dma controller's property names

2015-02-24T18:35:43+00:00

According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.

Signed-off-by: Peter Ujfalusi 
Signed-off-by: Tony Lindgren

ARM: dts: omap5: Correct the dma controller's property names

2015-02-24T18:35:43+00:00

According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.

Signed-off-by: Peter Ujfalusi 
Signed-off-by: Tony Lindgren

ARM: dts: omap4: Correct the dma controller's property names

2015-02-24T18:35:43+00:00

According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.

Signed-off-by: Peter Ujfalusi 
Signed-off-by: Tony Lindgren

ARM: dts: omap3: Correct the dma controller's property names

2015-02-24T18:35:43+00:00

According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.

Signed-off-by: Peter Ujfalusi 
Signed-off-by: Tony Lindgren

ARM: dts: omap2: Correct the dma controller's property names

2015-02-24T18:35:43+00:00

According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.

Signed-off-by: Peter Ujfalusi 
Signed-off-by: Tony Lindgren

ARM: dts: am437x-idk: fix sleep pinctrl state

2015-02-24T18:35:43+00:00

we have i2c0 sleep pinctrl state but were passing
default state anyhow. Fix that.

Signed-off-by: Felipe Balbi 
Signed-off-by: Tony Lindgren

ARM: dts: am437x-idk: fix TPS62362 i2c bus

2015-02-24T18:35:43+00:00

As it turns out, tps62362 is actually on I2C bus0,
not bus1. This has gone unnoticed because Linux
doesn't use (as of now) that regulator at all, it's
setup by the bootloader and left as is.

While at that, also add missing reg property for
our regulator.

Signed-off-by: Felipe Balbi 
Signed-off-by: Tony Lindgren

ARM: dts: n900: Fix offset for smc91x ethernet

2015-02-24T18:35:43+00:00

Offset for smc91x must be zero otherwise smc91x linux kernel driver does not
detect smc91x ethernet hardware in qemu N900 machine.

The 0x300 offset was used to supress a warning the smsc911x
driver produces about non-standard offset as 0x300 seems to
be the EEPROM default. As only three address lines are
connected both 0 and 0x300 will work just fine with 0 being
correct. The warning about the non-standard offset can be
fixed by writing to EEPROM as that's needed in any case to
set the MAC address.

Signed-off-by: Pali Rohár 
[tony@atomide.com: updated comments, just use 0 instead of 0x0]
Signed-off-by: Tony Lindgren