SoC for 4.13:

 - New suspend/resume mode for sama5d2
 - Initial support for armv7m based SoCs

* tag 'at91-ab-4.13-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
  ARM: at91: remove atmel_nand_data
  ARM: at91: fix at91_suspend_entering_slow_clock link error
  ARM: at91: debug: add samv7x support
  ARM: at91: add armv7m SoC detection
  ARM: at91: handle CONFIG_PM for armv7m configurations
  ARM: at91: Add armv7m support
  ARM: at91: Document armv7m compatibles
  ARM: at91: Documentation: add armv7m families
  ARM: at91: pm: fallback to slowclock when backup mode fails
  ARM: at91: pm: allow selecting standby and suspend modes
  ARM: at91: pm: Add sama5d2 backup mode

Signed-off-by: Olof Johansson <olof@lixom.net>

Qualcomm ARM Based SoC Updates for v4.13

* Add debug UART addresses for IPQ4019

* tag 'qcom-soc-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
  ARM: debug: qcom: add UART addresses to Kconfig help for IPQ4019

Signed-off-by: Olof Johansson <olof@lixom.net>

Add information about the IPQ4019 debug UART physical and virtual
addresses in the DEBUG_QCOM_UARTDM Kconfig help section.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Add support for low level debugging on Atmel samv7x.

Signed-off-by: Szemző András <sza@esh.hu>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

RK1108 UARTs are Synopsis DesignWare 8250 compatible.
Only with different register addresses.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Jacob Chen <jacob2.chen@rock-chips.com>
[rk1108->rv1108 rename]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

There are multiple architectures that support CONFIG_DEBUG_RODATA and
CONFIG_SET_MODULE_RONX. These options also now have the ability to be
turned off at runtime. Move these to an architecture independent
location and make these options def_bool y for almost all of those
arches.

Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Kees Cook <keescook@chromium.org>

Pull "Renesas ARM Based SoC Updates for v4.9" from Simon Horman:

Clean-up:
* Only use smp_init when SMP is selected

Enablement:
* Add debug-ll support for r8a7992

* tag 'renesas-soc-for-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: r8a7791: only use smp_init when SMP is selected
  ARM: shmobile: r8a7790: only use smp_init when SMP is selected
  ARM: debug-ll: Add support for r8a7992

Enable low-level debugging support for R-Car V2H (r8a7792).
V2H uses SCIF0 for the debug console, like most other R-Car Gen2 SoCs.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The SUN_TOP_CTRL_FAMILY_ID register  is at a fixed absolute address for
all of our supported chips, so utilize its value to determine what the
UARTA base address should be based on the value we read.

Since the code is called both during decompressor when the MMU is off,
and after the MMU has been turned on in the kernel, and we want to do
the lookup only once, we use the same technique as tegra.S and have a
shared storage location between the decompressor and the kernel.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Merge "the second part of the Broadcom ARM-based SoC changes" from Florian Fainelli:

- Florian updates the DEBUG_UART_BCM5301X entry to cover both NS and NSP SoCs
  since they both have the same location

* tag 'arm-soc/for-4.8/soc-part2' of http://github.com/Broadcom/stblinux:
  ARM: debug: Enable DEBUG_BCM_5301X for Northstar Plus SoCs