Pull DeviceTree updates from Rob Herring:

 - vsprintf format specifier %pOF for device_node's. This will enable us
   to stop storing the full node names. Conversion of users will happen
   next cycle.

 - Update documentation to point to DT specification instead of ePAPR.

 - Split out graph and property functions to a separate file.

 - New of-graph functions for ALSA

 - Add vendor prefixes for RISC-V, Linksys, iWave Systems, Roofull,
   Itead, and BananaPi.

 - Improve dtx_diff utility filename printing.

* tag 'devicetree-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (32 commits)
  of: document /sys/firmware/fdt
  dt-bindings: Add RISC-V vendor prefix
  vsprintf: Add %p extension "%pOF" for device tree
  of: find_node_by_full_name rewrite to compare each level
  of: use kbasename instead of open coding
  dt-bindings: thermal: add file extension to brcm,ns-thermal
  of: update ePAPR references to point to Devicetree Specification
  scripts/dtc: dtx_diff - Show real file names in diff header
  of: detect invalid phandle in overlay
  of: be consistent in form of file mode
  of: make __of_attach_node() static
  of: address.c header comment typo
  of: fdt.c header comment typo
  of: make of_fdt_is_compatible() static
  dt-bindings: display-timing.txt convert non-ascii characters to ascii
  Documentation: remove overlay-notes reference to non-existent file
  dt-bindings: usb: exynos-usb: Add missing required VDD properties
  dt-bindings: Add vendor prefix for Linksys
  MAINTAINERS: add device tree ABI documentation file
  of: Add vendor prefix for iWave Systems Technologies Pvt. Ltd
  ...

Felipe writes:

usb: changes for v4.13 merge window

This time around we have a total of 57 non-merge commits. A list of
most important changes follows:

- Improvements to dwc3 tracing interface
- Initial dual-role support for dwc3
- Improvements to how we handle DMA resources in dwc3
- A new f_uac1 implementation which much more flexible
- Removal of AVR32 bits
- Improvements to f_mass_storage driver

Since commit bd8ce544ec35 ("usb: dwc3: exynos: Make provision for vdd
regulators") vdd33-supply and vdd10-supply are required so document them
in bindings.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>

The device node is used for UDCs integrated into Broadcom's
iProc family of SoCs'. The UDC is based on Synopsys Designware
Cores AHB Subsystem USB Device Controller IP.

Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We want the USB fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

With the runtime PM implemented for ohci-platform driver, we can
now support omap3 and later OHCI by adding one device tree
property.

Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB support in the Meson8 SoCs is provided by a DWC2 controller which
works with the same settings as Meson8b and GXBB. Using the generic
"snps,dwc2" binding results in an endless stream of "Overcurrent change
detected" messages.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds a quirk to disable USB 2.0 MAC linestate check
during HS transmit. Refer the dwc3 databook, we can use it for
some special platforms if the linestate not reflect the expected
line state(J) during transmission.

When use this quirk, the controller implements a fixed 40-bit
TxEndDelay after the packet is given on UTMI and ignores the
linestate during the transmit of a token (during token-to-token
and token-to-data IPGAP).

On some rockchip platforms (e.g. rk3399), it requires to disable
the u2mac linestate check to decrease the SSPLIT token to SETUP
token inter-packet delay from 566ns to 466ns, and fix the issue
that FS/LS devices not recognized if inserted through USB 3.0 HUB.

Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Pull dmaengine updates from Vinod Koul:
 "This time again a smaller update consisting of:

   - support for TI DA8xx dma controller and updates to the cppi driver

   - updates on bunch of drivers like xilinx, pl08x, stm32-dma, mv_xor,
     ioat, dmatest"

* tag 'dmaengine-4.12-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (35 commits)
  dmaengine: pl08x: remove lock documentation
  dmaengine: pl08x: fix pl08x_dma_chan_state documentation
  dmaengine: pl08x: Use the BIT() macro consistently
  dmaengine: pl080: Fix some missing kerneldoc
  dmaengine: pl080: Cut some unused defines
  dmaengine: dmatest: Add check for supported buffer count (sg_buffers)
  dmaengine: dmatest: Select DMA_ENGINE_RAID as its needed for the slave_sg test
  dmaengine: virt-dma: Convert to use list_for_each_entry_safe()
  dma-debug: use offset_in_page() macro
  dmaengine: mv_xor: use offset_in_page() macro
  dmaengine: dmatest: use offset_in_page() macro
  dmaengine: sun4i: fix invalid argument
  dmaengine: ioat: use setup_timer
  dmaengine: cppi41: Fix an Oops happening in cppi41_dma_probe()
  dmaengine: pl330: remove pdata based initialization
  dmaengine: cppi: fix build error due to bad variable
  dmaengine: imx-sdma: add 1ms delay to ensure SDMA channel is stopped
  dmaengine: cppi41: use managed functions devm_*()
  dmaengine: cppi41: fix cppi41_dma_tx_status() logic
  dmaengine: qcom_hidma: pause the channel on shutdown
  ...

Pull ARM Device-tree updates from Olof Johansson:
 "Device-tree continues to see lots of updates. The majority of patches
  here are smaller changes for new hardware on existing platforms, and
  there are a few larger changes worth pointing out.

  Major new platforms:

   - Gemini has been ported to DT, so a handful of "new" platforms moved
     over from board files

   - Rockchip RK3288 support for Tinkerboard and Phytec phyCORE-RK3288
     SoM and RDK

   - A bunch of embedded platforms, several Linksys platforms, Synology
     DS116,

   - Motorola Droid4 (really old OMAP-based phone) support is added.

  Some refactorings, i.e. Allwinner H3/H5 support is commonalized.

  And lots of smaller changes, cleanups, etc. See shortlog for more
  description

  We're adding ability to cross-include DT files between arm and arm64,
  by creating appropriate links in the dt-include directory, and using
  arm/ and arm64/ as include prefixes. This will avoid other local hacks
  such as per-file links between the two arch trees (this broke for
  external mirroring of DT contents). Now they can just provide their
  own appropriate dt-include hierarcy per platform"

* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (349 commits)
  ARM: dts: exynos: Use - instead of @ for DT OPP entries
  arm: spear6xx: add DT description of the ADC on SPEAr600
  arm: spear6xx: remove unneeded pinctrl properties in spear600-evb
  arm: spear6xx: switch spear600-evb to the new flash partition DT binding
  arm: spear6xx: fix spaces in spear600-evb.dts
  arm: spear6xx: use node labels in spear600-evb.dts
  arm: spear6xx: add labels to various nodes in spear600.dtsi
  ARM: dts: vexpress: fix few unit address format warnings
  ARM: dts: at91: sama5d3_xplained: not all ADC channels are available
  ARM: dts: at91: sama5d3_xplained: fix ADC vref
  ARM: dts: at91: add envelope detector mux to the Axentia TSE-850
  ARM: dts: armada-38x: label USB and SATA nodes
  ARM: dts: imx6q-utilite-pro: add hpd gpio
  ARM: dts: imx6qp-sabresd: Set reg_arm regulator supply
  ARM: dts: imx6qdl-sabresd: Set LDO regulator supply
  ARM: dts: imx: add Gateworks Ventana GW5903 support
  ARM: dts: i.MX25: add AIPS control registers
  ARM: dts: imx7-colibri: add Carrier Board 3.3V/5V regulators
  ARM: dts: imx7-colibri: remove 1.8V fixed regulator
  ARM: dts: imx7-colibri: allow to disable Ethernet rail
  ...