USB support in the Meson8 SoCs is provided by a DWC2 controller which works with the same settings as Meson8b and GXBB. Using the generic "snps,dwc2" binding results in an endless stream of "Overcurrent change detected" messages. Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Pull dmaengine updates from Vinod Koul:
"This time again a smaller update consisting of:
- support for TI DA8xx dma controller and updates to the cppi driver
- updates on bunch of drivers like xilinx, pl08x, stm32-dma, mv_xor,
ioat, dmatest"
* tag 'dmaengine-4.12-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (35 commits)
dmaengine: pl08x: remove lock documentation
dmaengine: pl08x: fix pl08x_dma_chan_state documentation
dmaengine: pl08x: Use the BIT() macro consistently
dmaengine: pl080: Fix some missing kerneldoc
dmaengine: pl080: Cut some unused defines
dmaengine: dmatest: Add check for supported buffer count (sg_buffers)
dmaengine: dmatest: Select DMA_ENGINE_RAID as its needed for the slave_sg test
dmaengine: virt-dma: Convert to use list_for_each_entry_safe()
dma-debug: use offset_in_page() macro
dmaengine: mv_xor: use offset_in_page() macro
dmaengine: dmatest: use offset_in_page() macro
dmaengine: sun4i: fix invalid argument
dmaengine: ioat: use setup_timer
dmaengine: cppi41: Fix an Oops happening in cppi41_dma_probe()
dmaengine: pl330: remove pdata based initialization
dmaengine: cppi: fix build error due to bad variable
dmaengine: imx-sdma: add 1ms delay to ensure SDMA channel is stopped
dmaengine: cppi41: use managed functions devm_*()
dmaengine: cppi41: fix cppi41_dma_tx_status() logic
dmaengine: qcom_hidma: pause the channel on shutdown
...
Pull ARM Device-tree updates from Olof Johansson:
"Device-tree continues to see lots of updates. The majority of patches
here are smaller changes for new hardware on existing platforms, and
there are a few larger changes worth pointing out.
Major new platforms:
- Gemini has been ported to DT, so a handful of "new" platforms moved
over from board files
- Rockchip RK3288 support for Tinkerboard and Phytec phyCORE-RK3288
SoM and RDK
- A bunch of embedded platforms, several Linksys platforms, Synology
DS116,
- Motorola Droid4 (really old OMAP-based phone) support is added.
Some refactorings, i.e. Allwinner H3/H5 support is commonalized.
And lots of smaller changes, cleanups, etc. See shortlog for more
description
We're adding ability to cross-include DT files between arm and arm64,
by creating appropriate links in the dt-include directory, and using
arm/ and arm64/ as include prefixes. This will avoid other local hacks
such as per-file links between the two arch trees (this broke for
external mirroring of DT contents). Now they can just provide their
own appropriate dt-include hierarcy per platform"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (349 commits)
ARM: dts: exynos: Use - instead of @ for DT OPP entries
arm: spear6xx: add DT description of the ADC on SPEAr600
arm: spear6xx: remove unneeded pinctrl properties in spear600-evb
arm: spear6xx: switch spear600-evb to the new flash partition DT binding
arm: spear6xx: fix spaces in spear600-evb.dts
arm: spear6xx: use node labels in spear600-evb.dts
arm: spear6xx: add labels to various nodes in spear600.dtsi
ARM: dts: vexpress: fix few unit address format warnings
ARM: dts: at91: sama5d3_xplained: not all ADC channels are available
ARM: dts: at91: sama5d3_xplained: fix ADC vref
ARM: dts: at91: add envelope detector mux to the Axentia TSE-850
ARM: dts: armada-38x: label USB and SATA nodes
ARM: dts: imx6q-utilite-pro: add hpd gpio
ARM: dts: imx6qp-sabresd: Set reg_arm regulator supply
ARM: dts: imx6qdl-sabresd: Set LDO regulator supply
ARM: dts: imx: add Gateworks Ventana GW5903 support
ARM: dts: i.MX25: add AIPS control registers
ARM: dts: imx7-colibri: add Carrier Board 3.3V/5V regulators
ARM: dts: imx7-colibri: remove 1.8V fixed regulator
ARM: dts: imx7-colibri: allow to disable Ethernet rail
...
STM32 DT updates for v4.12, round 1 Highlights: ---------- - ADD RTC support on STM32F746 MCU - Enable RTC on STM32F746 Eval board - Enable clocks on STM32F746 MCU - Enable DMA, pwm1 and pwm3 on STM32F429I Eval - Add support of STM32H743 MCU and his Eval board - Enable USB HS and FS on STM32F469 Disco board * tag 'stm32-dt-for-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: dt-bindings: Document the STM32 USB OTG DWC2 core binding ARM: dts: stm32: Enable USB HS in FS mode (embedded phy) on stm32f429-disco ARM: dts: stm32: Enable USB FS on stm32f469-disco ARM: dts: stm32: Add USB FS support for STM32F429 MCU ARM: dts: stm32: Add STM32H743 MCU and STM32H743i-EVAL board ARM: dts: stm32: Enable pwm1 and pwm3 on stm32f429i-eval ARM: dts: stm32: Enable dma by default on stm32f4 adc ARM: dts: stm32: enable RTC on stm32746g-eval ARM: dts: stm32: Add RTC support for STM32F746 MCU ARM: dts: stm32: set HSE_RTC clock frequency to 1 MHz on stm32f746 dt-bindings: mfd: Add STM32F7 RCC numeric constants into DT include file ARM: dts: stm32: Enable clocks for STM32F746 MCU Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds the documentation for STM32F4x9 USB OTG FS/HS compatible strings. Signed-off-by: Bruno Herrera <bruherrera@gmail.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
- Add a new compatible string for the Armada 3700 SoCs - add sbuscfg support for orion usb controller driver. For the SoCs without hlock, need to program BAWR/BARD/AHBBRST fields in the sbuscfg register to guarantee the AHB master's burst would not overrun or underrun the FIFO. - the sbuscfg register has to be set after the usb controller reset, otherwise the value would be overridden to 0. In order to do this, the reset callback is registered. [gregory.clement@free-electrons.com: - reword commit and comments - fix error path in ehci_orion_drv_reset() - fix checkpatch warning] Signed-off-by: Hua Jing <jinghua@marvell.com> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EHCI controllers will have a companion controller. However, on platform bus, there was difficult to bind them in previous code. So, this patch adds helper functions to bind them using a "companion" property. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark the reg property as required and furthermore fix some typos and spellings in the documentation. Signed-off-by: Richard Leitner <richard.leitner@skidata.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename oc-delay-* to oc-delay-us and make it expect a time value. Furthermore add -ms suffix to power-on-time. There changes were suggested by Rob Herring in https://lkml.org/lkml/2017/2/15/1283. Signed-off-by: Richard Leitner <richard.leitner@skidata.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the max_{power,current}_{sp,bp} properties of the usb251xb driver
from devicetree. This is done to simplify the dt bindings as requested
by Rob Herring in https://lkml.org/lkml/2017/2/15/1283. If those
properties are ever needed by somebody they can be enabled again easily.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>