using LVDS channel 1 on an i.MX53 leads to following error:

imx-ldb 53fa8008.ldb: unable to set di0 parent clock to ldb_di1

This comes from imx_ldb_set_clock with mux = 0. Mux parameter must be "1" for
reparenting di1 clock to ldb_di1. The value of the mux param comes from device
tree port settings.

On i.MX5, the internal two-input-multiplexer is used. Due to hardware limitations,
only one port (port@[0,1]) can be used for each channel (lvds-channel@[0,1],
respectively)

Documentation update suggested by Philipp Zabel <p.zabel@pengutronix.de>

Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Fixes: e05c8c9a790a ("ARM: dts: imx53: Add IPU DI ports and endpoints, move imx-drm node to dtsi")
Cc: <stable@vger.kernel.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Support the LVDS666 format on the IPUv3 parallel display.
This makes the screen work on my Hercules eCAFE Slim HD.

Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds device tree binding documentation for the HDMI transmitter
on i.MX6.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This patch updates the device tree binding documentation for i.MX IPU/display
nodes using the OF graph bindings documented in
Documentation/devicetree/bindings/media/video-interfaces.txt.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Now that the DWC2 driver has been moved to drivers/usb, move its
bindings doc to the correct place

Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Eli Billauer <eli.billauer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The DWC2 USB controller in the BCM2835 (Raspberry Pi) needs some non-
default parameters. Select these based on the compatible value from the
DT node. For all other HW, fall back to the default parameters currently
in use.

The values in params_bcm2835[] were posted to the mailing list by Paul
quite some time ago. I made a couple of minor modifications since then;
to set ahbcfg instead of ahb_single, and to set uframe_sched.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This is an RFC for the new touchscreen properties.

Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
CC: linux-arm-kernel@lists.infradead.org
CC: linux-input@vger.kernel.org
CC: devel@driverdev.osuosl.org
CC: Marek Vasut <marex@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: devicetree@vger.kernel.org

This adds support for the LVDS Display Bridge contained
in i.MX5 and i.MX6 SoCs.

Bit mapping, data width, and video timings are configurable
via device tree. Dual-channel mode is supported for a single
high-resolution source.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull ARM SoC platform updates (part 3) from Arnd Bergmann:
 "This is the third and smallest of the SoC specific updates.  Changes
  include:

   - SMP support for the Xilinx zynq platform
   - Smaller imx changes
   - LPAE support for mvebu
   - Moving the orion5x, kirkwood, dove and mvebu platforms to a common
     "mbus" driver for their internal devices.

  It would be good to get feedback on the location of the "mbus" driver.
  Since this is used on multiple platforms may potentially get shared
  with other architectures (powerpc and arm64), it was moved to
  drivers/bus/.  We expect other similar drivers to get moved to the
  same place in order to avoid creating more top-level directories under
  drivers/ or cluttering up the messy drivers/misc/ even more."

* tag 'soc-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
  ARM: imx: reset_controller may be disabled
  ARM: mvebu: Align the internal registers virtual base to support LPAE
  ARM: mvebu: Limit the DMA zone when LPAE is selected
  arm: plat-orion: remove addr-map code
  arm: mach-mv78xx0: convert to use the mvebu-mbus driver
  arm: mach-orion5x: convert to use mvebu-mbus driver
  arm: mach-dove: convert to use mvebu-mbus driver
  arm: mach-kirkwood: convert to use mvebu-mbus driver
  arm: mach-mvebu: convert to use mvebu-mbus driver
  ARM i.MX53: set CLK_SET_RATE_PARENT flag on the tve_ext_sel clock
  ARM i.MX53: tve_di clock is not part of the CCM, but of TVE
  ARM i.MX53: make tve_ext_sel propagate rate change to PLL
  ARM i.MX53: Remove unused tve_gate clkdev entry
  ARM i.MX5: Remove tve_sel clock from i.MX53 clock tree
  ARM: i.MX5: Add PATA and SRTC clocks
  ARM: imx: do not bring up unavailable cores
  ARM: imx: add initial imx6dl support
  ARM: imx1: mm: add call to mxc_device_init
  ARM: imx_v4_v5_defconfig: Add CONFIG_GPIO_SYSFS
  ARM: imx_v6_v7_defconfig: Select CONFIG_PERF_EVENTS
  ...