Pull pin control changes from Linus Walleij:

 - A large slew of improvements of the Genric pin configuration support,
   and deployment in four different platforms: Rockchip, Super-H PFC,
   ABx500 and TZ1090.  Support BIAS_BUS_HOLD, get device tree parsing
   and debugfs support into shape.

 - We also have device tree support with generic naming conventions for
   the generic pin configuration.

 - Delete the unused and confusing direct pinconf API.  Now state
   transitions is *the* way to control pins and multiplexing.

 - New drivers for Rockchip, TZ1090, and TZ1090 PDC.

 - Two pin control states related to power management are now handled in
   the device core: "sleep" and "idle", removing a lot of boilerplate
   code in drivers.  We do not yet know if this is the final word for
   pin PM, but it already make things a lot easier to handle.

 - Handle sparse GPIO ranges passing a list of disparate pins, and
   utilize these in the new BayTrail (x86 Atom SoC) driver.

 - Make the sunxi (AllWinner) driver handle external interrupts.

 - Make it possible for pinctrl-single to handle the case where several
   pins are managed by a single register, and augment it to handle sleep
   modes.

 - Cleanups and improvements for the abx500 drivers.

 - Move Sirf pin control drivers to their own directory, support
   save/restore of context and add support for the SiRFatlas6 SoC.

 - PMU muxing for the Dove pinctrl driver.

 - Finalization and support for VF610 in the i.MX6 pinctrl driver.

 - Smoothen out various Exynos rough edges.

 - Generic cleanups of various kinds.

* tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (82 commits)
  pinctrl: vt8500: wmt: remove redundant dev_err call in wmt_pinctrl_probe()
  pinctrl: remove bindings for pinconf options needing more thought
  pinctrl: remove slew-rate parameter from tz1090
  pinctrl: set unit for debounce time pinconfig to usec
  pinctrl: more clarifications for generic pull configs
  pinctrl: rip out the direct pinconf API
  pinctrl-tz1090-pdc: add TZ1090 PDC pinctrl driver
  pinctrl-tz1090: add TZ1090 pinctrl driver
  pinctrl: samsung: Staticize drvdata_list
  pinctrl: rockchip: Add missing irq_gc_unlock() call before return error
  pinctrl: abx500: rework error path
  pinctrl: abx500: suppress hardcoded value
  pinctrl: abx500: factorize code
  pinctrl: abx500: fix abx500_gpio_get()
  pinctrl: abx500: fix abx500_pin_config_set()
  pinctrl: abx500: Add device tree support
  sh-pfc: Guard DT parsing with #ifdef CONFIG_OF
  pinctrl: add Intel BayTrail GPIO/pinctrl support
  pinctrl: fix pinconf_ops::pin_config_dbg_parse_modify kerneldoc
  pinctrl: Staticize local symbols
  ...

Conflicts:
	drivers/net/ethernet/ti/davinci_mdio.c
	drivers/pinctrl/Makefile

Pull regmap updates from Mark Brown:
 "A small but useful set of regmap updates this time around:

   - An abstraction for bitfields within a register map contributed by
     Srinivas Kandagatla, allowing drivers to cope more easily when
     hardware designers randomly move things about (mainly when talking
     to things like system controllers).

   - Changes from Lars-Peter Clausen to allow the MMIO regmap to be used
     from hard IRQ context.

   - Small improvements to the cache infrastructure and performance,
     including a default cache sync operation so now all regmaps can
     sync easily.

  There's also a pinctrl driver making use of the new bitfield API,
  merged here for dependency reasons.  There will be a simple add/add
  conflict with the pinctrl tree as a result."

* tag 'regmap-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  pinctrl: st: Remove unnecessary use of of_match_ptr macro
  pinctrl: st: fix return value check
  pinctrl: st: Add pinctrl and pinconf support.
  regmap: debugfs: Suppress cache for partial register files
  regmap: Add regmap_field APIs
  regmap: core: Cache all registers by default when cache is enabled
  regmap: Implemented default cache sync operation
  regmap: Make regmap-mmio usable from atomic contexts
  regmap: regcache: Fixup locking for custom lock callbacks
  regmap: debugfs: Fix return from regmap_debugfs_get_dump_start
  regmap: debugfs: Don't mark lockdep as broken due to debugfs write
  regmap: rbtree: Use range information to allocate nodes
  regmap: rbtree: Factor out node allocation
  regmap: Make regmap_check_range_table() a public API
  regmap: Add support for discarding parts of the register cache

Pull ARM SoC late changes from Arnd Bergmann:
 "These are changes that arrived a little late before the merge window
  or that have multiple dependencies on previous branches so they did
  not fit into one of the earlier ones.  There are 10 branches merged
  here, a total of 39 non-merge commits.  Contents are a mixed bag for
  the above reasons:

   * Two new SoC platforms: ST microelectronics stixxxx and the TI
     'Nspire' graphing calculator.  These should have been in the 'soc'
     branch but were a little late
   * Support for the Exynos 5420 variant in mach-exynos, which is based
     on the other exynos branches to avoid conflicts.
   * Various small changes for sh-mobile, ux500 and davinci
   * Common clk support for MSM"

* tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
  ARM: ux500: bail out on alien cpus
  ARM: davinci: da850: adopt to pinctrl-single change for configuring multiple pins
  serial: sh-sci: Initialise variables before access in sci_set_termios()
  ARM: stih41x: Add B2020 board support
  ARM: stih41x: Add B2000 board support
  ARM: sti: Add DEBUG_LL console support
  ARM: sti: Add STiH416 SOC support
  ARM: sti: Add STiH415 SOC support
  ARM: msm: Migrate to common clock framework
  ARM: msm: Make proc_comm clock control into a platform driver
  ARM: msm: Prepare clk_get() users in mach-msm for clock-pcom driver
  ARM: msm: Remove clock-7x30.h include file
  ARM: msm: Remove custom clk_set_{max,min}_rate() API
  ARM: msm: Remove custom clk_set_flags() API
  msm: iommu: Use clk_set_rate() instead of clk_set_min_rate()
  msm: iommu: Convert to clk_prepare/unprepare
  msm_sdcc: Convert to clk_prepare/unprepare
  usb: otg: msm: Convert to clk_prepare/unprepare
  msm_serial: Use devm_clk_get() and properly return errors
  msm_serial: Convert to clk_prepare/unprepare
  ...

Pull ARM SoC driver specific changes from Arnd Bergmann:
 "These changes are all driver specific and cross over between arm-soc
  contents and some other subsystem, in these cases cpufreq, crypto,
  dma, pinctrl, mailbox and usb, and the subsystem owners agreed to have
  these changes merged through arm-soc.

  As we proceed to untangle the dependencies between platform code and
  driver code, the amount of changes in this category is fortunately
  shrinking, for 3.11 we have 16 branches here and 101 non-merge
  changesets, the majority of which are for the stedma40 dma engine
  driver used in the ux500 platform.  Cleaning up that code touches
  multiple subsystems, but gets rid of the dependency in the end.

  The mailbox code moved out from mach-omap2 to drivers/mailbox is an
  intermediate step and is still omap specific at the moment.  Patches
  exist to generalize the subsystem and add other drivers with the same
  API, but those did not make it for 3.11."

* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (101 commits)
  crypto: ux500: use dmaengine_submit API
  crypto: ux500: use dmaengine_prep_slave_sg API
  crypto: ux500: use dmaengine_device_control API
  crypto: ux500/crypt: add missing __iomem qualifiers
  crypto: ux500/hash: add missing static qualifiers
  crypto: ux500/hash: use readl on iomem addresses
  dmaengine: ste_dma40: Declare memcpy config as static
  ARM: ux500: Remove mop500_snowball_ethernet_clock_enable()
  ARM: ux500: Correct the EN_3v3 regulator's on/off GPIO
  ARM: ux500: Provide a AB8500 GPIO Device Tree node
  gpio: rcar: fix gpio_rcar_of_table
  gpio-rcar: Remove #ifdef CONFIG_OF around OF-specific sections
  gpio-rcar: Reference core gpio documentation in the DT bindings
  clk: exynos5250: Add enum entries for divider clock of i2s1 and i2s2
  ARM: dts: Update Samsung I2S documentation
  ARM: dts: add clock provider information for i2s controllers in Exynos5250
  ARM: dts: add Exynos audio subsystem clock controller node
  clk: samsung: register audio subsystem clocks using common clock framework
  ARM: dts: use #include for all device trees for Samsung
  pinctrl: s3c24xx: use correct header for chained_irq functions
  ...

This patch add pinctrl support to ST SoCs.

About hardware:
ST Set-Top-Box parts have two blocks called PIO and PIO-mux which handle
pin configurations.

Each multi-function pin is controlled, driven and routed through the PIO
multiplexing block. Each pin supports GPIO functionality (ALT0) and
multiple alternate functions(ALT1 - ALTx) that directly connect the pin
to different hardware blocks. When a pin is in GPIO mode, Output Enable
(OE), Open Drain(OD), and Pull Up (PU) are driven by the related PIO
block. Otherwise the PIO multiplexing block configures these parameters
and retiming the signal.

About driver:
This pinctrl driver manages both PIO and PIO-mux block using pinctrl,
pinconf, pinmux, gpio subsystems. All the pinctrl related config
information can only come from device trees.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>

Some options currently take arguments in unspecified driver-specific units.
As pointed out by Stephen Warren, driver specific values should not be part
of generic devicetree bindings describing the hardware.

Therefore remove the critical bindings again, before they become part of
an official release.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

As the binding for slew-rate is under discussion and seems to need
more tought it will get removed for now, so it doesn't get an offical
release.

Therefore remove it again from the only current user, tz1090.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Currently the debounce time pinconfig option uses an unspecified
"time units" unit. As pinconfig options should use SI units and a
real unit is also necessary for generic dt bindings, change it
to usec. Currently no driver is using the generic pinconfig option
for this, so the unit change is safe to do.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

PULL_PIN_DEFAULT is meant for hardware completely hiding any pull
settings from the driver, so that it's really only possible to turn
the pull on or off, but it not being possible to determine any
pull settings from software.

Also the binding-documentation for the pull arguments did not match
the changes to the expected values.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add a pin control driver for the TZ1090's low power pins via the
powerdown controller SOC_GPIO_CONTROL registers.

These pins have individually controlled pull-up, and group controlled
schmitt, slew-rate, drive-strength, and power-on-start (pos).

The pdc_gpio0 and pdc_gpio1 pins can also be muxed onto the
ir_mod_stable_out and ir_mod_power_out functions respectively. If no
function is set they remain in GPIO mode. These muxes can be overridden
by requesting them as GPIOs.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-doc@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>