The defaults listed in the bindings don't match what the code is
actually doing.  Presumably existing users care more about keeping
existing behavior the same, so change the bindings to match the code
in Linux.

The "qcom,preemphasis-level" default has been wrong for quite a long
time (May 2018).  The other two were recently added.

As some evidence that these values are wrong, this is from the Linux
driver:
- qcom,preemphasis-level: sets "PORT_TUNE1", lower 2 bits.  Driver
  programs PORT_TUNE1 to 0x30 by default and (0x30 & 0x3) = 0.
- qcom,bias-ctrl-value: sets "PLL_BIAS_CONTROL_2", lower 6 bits.
  Driver programs PLL_BIAS_CONTROL_2 to 0x20 by default and (0x20 &
  0x3f) = 0x20 = 32.
- qcom,hsdisc-trim-value: sets "PORT_TUNE2", lower 2 bits.  Driver
  programs PORT_TUNE2 to 0x29 by default and (0x29 & 0x3) = 1.

Fixes: 1e6f134eb67a ("dt-bindings: phy: qcom-qusb2: Add support for overriding Phy tuning parameters")
Fixes: a8b70ccf10e3 ("dt-bindings: phy-qcom-usb2: Add support to override tuning values")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rob Herring <robh@kernel.org>

This file was removed, and another file was added instead of
it, on two separate commits.

Splitting a single logical change (doc conversion) on two
patches is a bad thing, as it makes harder to discover what
crap happened.

Anyway, this patch fixes the broken reference, making it
pointing to the new location of the file.

Fixes: 922003733d42 ("dt-bindings: phy: Remove Cadence MHDP PHY dt binding")
Fixes: c6d8eef38b7f ("dt-bindings: phy: Add Cadence MHDP PHY bindings in YAML format.")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>

Pull ARM SoC updates from Arnd Bergmann:
 "The code changes are mostly for 32-bit platforms and include:

   - Lots of updates for the Nvidia Tegra platform, including cpuidle,
     pmc, and dt-binding changes

   - Microchip at91 power management updates for the recently added
     sam9x60 SoC

   - Treewide setup_irq deprecation by afzal mohammed

   - STMicroelectronics stm32 gains earlycon support

   - Renesas platforms with Cortex-A9 can now use the global timer

   - Some TI OMAP2+ platforms gain cpuidle support

   - Various cleanups for the i.MX6 and Orion platforms, as well as
     Kconfig files across all platforms"

* tag 'arm-soc-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (75 commits)
  ARM: qcom: Add support for IPQ40xx
  ARM: mmp: replace setup_irq() by request_irq()
  ARM: cns3xxx: replace setup_irq() by request_irq()
  ARM: spear: replace setup_irq() by request_irq()
  ARM: ep93xx: Replace setup_irq() by request_irq()
  ARM: iop32x: replace setup_irq() by request_irq()
  arm: mach-dove: Mark dove_io_desc as __maybe_unused
  ARM: orion: replace setup_irq() by request_irq()
  ARM: debug: stm32: add UART early console support for STM32MP1
  ARM: debug: stm32: add UART early console support for STM32H7
  ARM: debug: stm32: add UART early console configuration for STM32F7
  ARM: debug: stm32: add UART early console configuration for STM32F4
  cpuidle: tegra: Disable CC6 state if LP2 unavailable
  cpuidle: tegra: Squash Tegra114 driver into the common driver
  cpuidle: tegra: Squash Tegra30 driver into the common driver
  cpuidle: Refactor and move out NVIDIA Tegra20 driver into drivers/cpuidle
  ARM: tegra: cpuidle: Remove unnecessary memory barrier
  ARM: tegra: cpuidle: Make abort_flag atomic
  ARM: tegra: cpuidle: Handle case where secondary CPU hangs on entering LP2
  ARM: tegra: Make outer_disable() open-coded
  ...

Pull pci updates from Bjorn Helgaas:
 "Enumeration:

   - Revert sysfs "rescan" renames that broke apps (Kelsey Skunberg)

   - Add more 32 GT/s link speed decoding and improve the implementation
     (Yicong Yang)

  Resource management:

   - Add support for sizing programmable host bridge apertures and fix a
     related alpha Nautilus regression (Ivan Kokshaysky)

  Interrupts:

   - Add boot interrupt quirk mechanism for Xeon chipsets and document
     boot interrupts (Sean V Kelley)

  PCIe native device hotplug:

   - When possible, disable in-band presence detect and use PDS
     (Alexandru Gagniuc)

   - Add DMI table for devices that don't use in-band presence detection
     but don't advertise that correctly (Stuart Hayes)

   - Fix hang when powering slots up/down via sysfs (Lukas Wunner)

   - Fix an MSI interrupt race (Stuart Hayes)

  Virtualization:

   - Add ACS quirks for Zhaoxin devices (Raymond Pang)

  Error handling:

   - Add Error Disconnect Recover (EDR) support so firmware can report
     devices disconnected via DPC and we can try to recover (Kuppuswamy
     Sathyanarayanan)

  Peer-to-peer DMA:

   - Add Intel Sky Lake-E Root Ports B, C, D to the whitelist (Andrew
     Maier)

  ASPM:

   - Reduce severity of common clock config message (Chris Packham)

   - Clear the correct bits when enabling L1 substates, so we don't go
     to the wrong state (Yicong Yang)

  Endpoint framework:

   - Replace EPF linkup ops with notifier call chain and improve locking
     (Kishon Vijay Abraham I)

   - Fix concurrent memory allocation in OB address region (Kishon Vijay
     Abraham I)

   - Move PF function number assignment to EPC core to support multiple
     function creation methods (Kishon Vijay Abraham I)

   - Fix issue with clearing configfs "start" entry (Kunihiko Hayashi)

   - Fix issue with endpoint MSI-X ignoring BAR Indicator and Table
     Offset (Kishon Vijay Abraham I)

   - Add support for testing DMA transfers (Kishon Vijay Abraham I)

   - Add support for testing > 10 endpoint devices (Kishon Vijay Abraham I)

   - Add support for tests to clear IRQ (Kishon Vijay Abraham I)

   - Add common DT schema for endpoint controllers (Kishon Vijay Abraham I)

  Amlogic Meson PCIe controller driver:

   - Add DT bindings for AXG PCIe PHY, shared MIPI/PCIe analog PHY (Remi
     Pommarel)

   - Add Amlogic AXG PCIe PHY, AXG MIPI/PCIe analog PHY drivers (Remi
     Pommarel)

  Cadence PCIe controller driver:

   - Add Root Complex/Endpoint DT schema for Cadence PCIe (Kishon Vijay
     Abraham I)

  Intel VMD host bridge driver:

   - Add two VMD Device IDs that require bus restriction mode (Sushma
     Kalakota)

  Mobiveil PCIe controller driver:

   - Refactor and modularize mobiveil driver (Hou Zhiqiang)

   - Add support for Mobiveil GPEX Gen4 host (Hou Zhiqiang)

  Microsoft Hyper-V host bridge driver:

   - Add support for Hyper-V PCI protocol version 1.3 and
     PCI_BUS_RELATIONS2 (Long Li)

   - Refactor to prepare for virtual PCI on non-x86 architectures (Boqun
     Feng)

   - Fix memory leak in hv_pci_probe()'s error path (Dexuan Cui)

  NVIDIA Tegra PCIe controller driver:

   - Use pci_parse_request_of_pci_ranges() (Rob Herring)

   - Add support for endpoint mode and related DT updates (Vidya Sagar)

   - Reduce -EPROBE_DEFER error message log level (Thierry Reding)

  Qualcomm PCIe controller driver:

   - Restrict class fixup to specific Qualcomm devices (Bjorn Andersson)

  Synopsys DesignWare PCIe controller driver:

   - Refactor core initialization code for endpoint mode (Vidya Sagar)

   - Fix endpoint MSI-X to use correct table address (Kishon Vijay
     Abraham I)

  TI DRA7xx PCIe controller driver:

   - Fix MSI IRQ handling (Vignesh Raghavendra)

  TI Keystone PCIe controller driver:

   - Allow AM654 endpoint to raise MSI-X interrupt (Kishon Vijay Abraham I)

  Miscellaneous:

   - Quirk ASMedia XHCI USB to avoid "PME# from D0" defect (Kai-Heng
     Feng)

   - Use ioremap(), not phys_to_virt(), for platform ROM to fix video
     ROM mapping with CONFIG_HIGHMEM (Mikel Rychliski)"

* tag 'pci-v5.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (96 commits)
  misc: pci_endpoint_test: remove duplicate macro PCI_ENDPOINT_TEST_STATUS
  PCI: tegra: Print -EPROBE_DEFER error message at debug level
  misc: pci_endpoint_test: Use full pci-endpoint-test name in request_irq()
  misc: pci_endpoint_test: Fix to support > 10 pci-endpoint-test devices
  tools: PCI: Add 'e' to clear IRQ
  misc: pci_endpoint_test: Add ioctl to clear IRQ
  misc: pci_endpoint_test: Avoid using module parameter to determine irqtype
  PCI: keystone: Allow AM654 PCIe Endpoint to raise MSI-X interrupt
  PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get correct MSI-X table address
  PCI: endpoint: Fix ->set_msix() to take BIR and offset as arguments
  misc: pci_endpoint_test: Add support to get DMA option from userspace
  tools: PCI: Add 'd' command line option to support DMA
  misc: pci_endpoint_test: Use streaming DMA APIs for buffer allocation
  PCI: endpoint: functions/pci-epf-test: Print throughput information
  PCI: endpoint: functions/pci-epf-test: Add DMA support to transfer data
  PCI: pciehp: Fix MSI interrupt race
  PCI: pciehp: Fix indefinite wait on sysfs requests
  PCI: endpoint: Fix clearing start entry in configfs
  PCI: tegra: Add support for PCIe endpoint mode in Tegra194
  PCI: sysfs: Revert "rescan" file renames
  ...

Pull devicetree updates from Rob Herring:

 - Unit test for overlays with GPIO hogs

 - Improve dma-ranges parsing to handle dma-ranges with multiple entries

 - Update dtc to upstream version v1.6.0-2-g87a656ae5ff9

 - Improve overlay error reporting

 - Device link support for power-domains and hwlocks bindings

 - Add vendor prefixes for Beacon, Topwise, ENE, Dell, SG Micro, Elida,
   PocketBook, Xiaomi, Linutronix, OzzMaker, Waveshare Electronics, and
   ITE Tech

 - Add deprecated Marvell vendor prefix 'mrvl'

 - A bunch of binding conversions to DT schema continues. Of note, the
   common serial and USB connector bindings are converted.

 - Add more Arm CPU compatibles

 - Drop Mark Rutland as DT maintainer :(

* tag 'devicetree-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (106 commits)
  MAINTAINERS: drop an old reference to stm32 pwm timers doc
  MAINTAINERS: dt: update etnaviv file reference
  dt-bindings: usb: dwc2: fix bindings for amlogic, meson-gxbb-usb
  dt-bindings: uniphier-system-bus: fix warning in the example
  dt-bindings: display: meson-vpu: fix indentation of reg-names' "items"
  dt-bindings: iio: Fix adi, ltc2983 uint64-matrix schema constraints
  dt-bindings: power: Fix example for power-domain
  dt-bindings: arm: Add some constraints for PSCI nodes
  of: some unittest overlays not untracked
  of: gpio unittest kfree() wrong object
  dt-bindings: phy: convert phy-rockchip-inno-usb2 bindings to yaml
  dt-bindings: serial: sh-sci: Convert to json-schema
  dt-bindings: serial: Document serialN aliases
  dt-bindings: thermal: tsens: Set 'additionalProperties: false'
  dt-bindings: thermal: tsens: Fix nvmem-cell-names schema
  dt-bindings: vendor-prefixes: Add Beacon vendor prefix
  dt-bindings: vendor-prefixes: Add Topwise
  of: of_private.h: Replace zero-length array with flexible-array member
  docs: dt: fix a broken reference to input.yaml
  docs: dt: fix references to ap806-system-controller.txt
  ...

Current dts files for Rockchip with 'usb2-phy' subnodes
are manually verified. In order to automate this process
phy-rockchip-inno-usb2.txt has to be converted to yaml.

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>

A rather straightforward conversion of the phy-mmp3-usb binding to DT
schema format using json-schema.

Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
[robh: add additionalProperties]
Signed-off-by: Rob Herring <robh@kernel.org>

Setting 'additionalProperties: false' is frequently omitted, but is
important in order to check that there aren't extra undocumented
properties in a binding.

Ideally, we'd just add this automatically and make this the default, but
there's some cases where it doesn't work. For example, if a common
schema is referenced, then properties in the common schema aren't part
of what's considered for 'additionalProperties'. Also, sometimes there
are bus specific properties such as 'spi-max-frequency' that go into
bus child nodes, but aren't defined in the child node's schema.

So let's stick with the json-schema defined default and add
'additionalProperties: false' where needed. This will be a continual
review comment and game of wack-a-mole.

Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Stephen Boyd <sboyd@kernel.org> # clock
Acked-by: Lee Jones <lee.jones@linaro.org>

Kishon writes:

phy: for 5.7

*) Rename and Re-design phy-cadence-dp driver to phy-cadence-torrent driver
*) Add new PHY driver for Qualcomm 28nm Hi-Speed USB PHY
*) Add new PHY driver for Qualcomm Super Speed PHY in QCS404
*) Add support for Qualcomm PCIe QMP/QHP PHY in SDM845 to phy-qcom-qmp driver
*) Add support for Qualcomm UFS PHY in MSM8996 to phy-qcom-qmp driver
*) Add support for an additional reference clock in Mediatek phy-mtk-tphy driver
*) Add support for configuring tuning parameters in Mediatek phy-mtk-tphy driver
*) Add support for GMII PHY in TI K3 AM654x/J721E SoCs to phy-gmii-sel driver
*) Add support for USB2 PHY in Amlogic A1 SoC Family to phy-meson-g12a-usb2
   driver
*) Add support for USB3/USB2/PCIe PHY in Socionext Pro5 SoC to
   phy-uniphier-usb3ss/phy-uniphier-usb3hs/phy-uniphier-pcie driver respectively
*) Add support for QUSB2 PHY in Qualcomm SC7180 in driver
*) Convert dt-bindings of Cadence DP, Qualcomm QUSB2 to YAML format

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

* tag 'phy-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (52 commits)
  phy: qcom-qusb2: Add new overriding tuning parameters in QUSB2 V2 PHY
  phy: qcom-qusb2: Add support for overriding tuning parameters in QUSB2 V2 PHY
  dt-bindings: phy: qcom-qusb2: Add support for overriding Phy tuning parameters
  phy: qcom-qusb2: Add generic QUSB2 V2 PHY support
  dt-bindings: phy: qcom,qusb2: Add compatibles for QUSB2 V2 phy and SC7180
  dt-bindings: phy: qcom,qusb2: Convert QUSB2 phy bindings to yaml
  phy: rk-inno-usb2: Decrease verbosity of repeating log.
  phy: amlogic: Add Amlogic A1 USB2 PHY Driver
  dt-bindings: phy: Add Amlogic A1 USB2 PHY Bindings
  phy: ti: gmii-sel: add support for am654x/j721e soc
  dt-bindings: phy: ti: gmii-sel: add support for am654x/j721e soc
  phy: qualcomm: usb: Add SuperSpeed PHY driver
  dt-bindings: Add Qualcomm USB SuperSpeed PHY bindings
  phy: qualcomm: Add Synopsys 28nm Hi-Speed USB PHY driver
  dt-bindings: phy: Add Qualcomm Synopsys Hi-Speed USB PHY binding
  dt-bindings: phy: remove qcom-dwc3-usb-phy
  phy: phy-mtk-tphy: add a new reference clock
  phy: phy-mtk-tphy: remove unused u3phya_ref clock
  phy: phy-mtk-tphy: make the ref clock optional
  phy: phy-mtk-tphy: add a property for internal resistance
  ...

Add support for overriding QUSB2 V2 phy tuning parameters
in device tree bindings.

Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>