Pull ARM DT updates from Olof Johansson:
"Device tree contents continue to be the largest branches we submit.
This time around, some of the contents worth pointing out is:
New SoC platforms:
- Freescale i.MX 7Solo
- Broadcom BCM23550
- Cirrus Logic EP7209 and EP7211 (clps711x platforms)_
- Hisilicon HI3519
- Renesas R8A7792
Some of the other delta that is sticking out, line-count wise:
- Exynos moves of IP blocks under an SoC bus, which causes a large
delta due to indentation changes
- a new Tegra K1 board: Apalis
- a bunch of small updates to many Allwinner platforms; new hardware
support, some cleanup, etc"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (426 commits)
ARM: dts: sun8i: Add dts file for inet86dz board
ARM: dts: sun8i: Add dts file for Polaroid MID2407PXE03 tablet
ARM: dts: sun8i: Use sun8i-reference-design-tablet for ga10h dts
ARM: dts: sun8i: Use sun8i-reference-design-tablet for polaroid mid2809pxe04
ARM: dts: sun8i: reference-design-tablet: Add drivevbus-supply
ARM: dts: Copy sun8i-q8-common.dtsi sun8i-reference-design-tablet.dtsi
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for utoo p66 dts
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for dit4350 dts
ARM: dts: sun5i: reference-design-tablet: Remove mention of q8
ARM: dts: sun5i: reference-design-tablet: Set lradc vref to avcc
ARM: dts: sun5i: Rename sun5i-q8-common.dtsi sun5i-reference-design-tablet.dtsi
ARM: dts: sun5i: Move q8 display bits to sun5i-a13-q8-tablet.dts
ARM: dts: sunxi: Rename sunxi-q8-common.dtsi sunxi-reference-design-tablet.dtsi
ARM: dts: at91: Don't build unnecessary dtbs
ARM: dts: at91: sama5d3x: separate motherboard gmac and emac definitions
ARM: dts: at91: at91sam9g25ek: fix isi endpoint node
ARM: dts: at91: move isi definition to at91sam9g25ek
ARM: dts: at91: fix i2c-gpio node name
ARM: dts: at91: vinco: fix regulator name
ARM: dts: at91: ariag25 : fix onewire node
...
Pull MMC updates from Ulf Hansson: "MMC core: - A couple of changes to improve the support for erase/discard/trim cmds - Add eMMC HS400 enhanced strobe support - Show OCR and DSR registers in SYSFS for MMC/SD cards - Correct and improve busy detection logic for MMC switch (CMD6) cmds - Disable HPI cmds for certain broken Hynix eMMC cards - Allow MMC hosts to specify non-support for SD and MMC cmds - Some minor additional fixes MMC host: - sdhci: Re-works, fixes and clean-ups - sdhci: Add HW auto re-tuning support - sdhci: Re-factor code to prepare for adding support for eMMC CMDQ - sdhci-esdhc-imx: Fixes and clean-ups - sdhci-esdhc-imx: Update system PM support - sdhci-esdhc-imx: Enable HW auto re-tuning - sdhci-bcm2835: Remove driver as sdhci-iproc is used instead - sdhci-brcmstb: Add new driver for Broadcom BRCMSTB SoCs - sdhci-msm: Add support for UHS cards - sdhci-tegra: Improve support for UHS cards - sdhci-of-arasan: Update phy support for Rockchip SoCs - sdhci-of-arasan: Deploy enhanced strobe support - dw_mmc: Some fixes and clean-ups - dw_mmc: Enable support for erase/discard/trim cmds - dw_mmc: Enable CMD23 support - mediatek: Some fixes related to the eMMC HS400 support - sh_mmcif: Improve support for HW busy detection - rtsx_pci: Enable support for erase/discard/trim cmds" * tag 'mmc-v4.8' of git://git.linaro.org/people/ulf.hansson/mmc: (135 commits) mmc: rtsx_pci: Remove deprecated create_singlethread_workqueue mmc: rtsx_pci: Enable MMC_CAP_ERASE to allow erase/discard/trim requests mmc: rtsx_pci: Use the provided busy timeout from the mmc core mmc: sdhci-pltfm: Drop define for SDHCI_PLTFM_PMOPS mmc: sdhci-pltfm: Convert to use the SET_SYSTEM_SLEEP_PM_OPS mmc: sdhci-pltfm: Make sdhci_pltfm_suspend|resume() static mmc: sdhci-esdhc-imx: Use common sdhci_suspend|resume_host() mmc: sdhci-esdhc-imx: Assign system PM ops within #ifdef CONFIG_PM_SLEEP mmc: sdhci-sirf: Remove non needed #ifdef CONFIG_PM* for dev_pm_ops mmc: sdhci-s3c: Remove non needed #ifdef CONFIG_PM for dev_pm_ops mmc: sdhci-pxav3: Remove non needed #ifdef CONFIG_PM for dev_pm_ops mmc: sdhci-of-esdhc: Simplify code by using SIMPLE_DEV_PM_OPS mmc: sdhci-acpi: Simplify code by using SET_SYSTEM_SLEEP_PM_OPS mmc: sdhci-pci-core: Simplify code by using SET_SYSTEM_SLEEP_PM_OPS mmc: Change the max discard sectors and erase response when HW busy detect phy: rockchip-emmc: Wait even longer for the DLL to lock phy: rockchip-emmc: Be tolerant to card clock of 0 in power on mmc: sdhci-of-arasan: Revert: Always power the PHY off/on when clock changes mmc: sdhci-msm: Add support for UHS cards mmc: sdhci-msm: Add set_uhs_signaling() implementation ...
Pull networking updates from David Miller:
1) Unified UDP encapsulation offload methods for drivers, from
Alexander Duyck.
2) Make DSA binding more sane, from Andrew Lunn.
3) Support QCA9888 chips in ath10k, from Anilkumar Kolli.
4) Several workqueue usage cleanups, from Bhaktipriya Shridhar.
5) Add XDP (eXpress Data Path), essentially running BPF programs on RX
packets as soon as the device sees them, with the option to mirror
the packet on TX via the same interface. From Brenden Blanco and
others.
6) Allow qdisc/class stats dumps to run lockless, from Eric Dumazet.
7) Add VLAN support to b53 and bcm_sf2, from Florian Fainelli.
8) Simplify netlink conntrack entry layout, from Florian Westphal.
9) Add ipv4 forwarding support to mlxsw spectrum driver, from Ido
Schimmel, Yotam Gigi, and Jiri Pirko.
10) Add SKB array infrastructure and convert tun and macvtap over to it.
From Michael S Tsirkin and Jason Wang.
11) Support qdisc packet injection in pktgen, from John Fastabend.
12) Add neighbour monitoring framework to TIPC, from Jon Paul Maloy.
13) Add NV congestion control support to TCP, from Lawrence Brakmo.
14) Add GSO support to SCTP, from Marcelo Ricardo Leitner.
15) Allow GRO and RPS to function on macsec devices, from Paolo Abeni.
16) Support MPLS over IPV4, from Simon Horman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
xgene: Fix build warning with ACPI disabled.
be2net: perform temperature query in adapter regardless of its interface state
l2tp: Correctly return -EBADF from pppol2tp_getname.
net/mlx5_core/health: Remove deprecated create_singlethread_workqueue
net: ipmr/ip6mr: update lastuse on entry change
macsec: ensure rx_sa is set when validation is disabled
tipc: dump monitor attributes
tipc: add a function to get the bearer name
tipc: get monitor threshold for the cluster
tipc: make cluster size threshold for monitoring configurable
tipc: introduce constants for tipc address validation
net: neigh: disallow transition to NUD_STALE if lladdr is unchanged in neigh_update()
MAINTAINERS: xgene: Add driver and documentation path
Documentation: dtb: xgene: Add MDIO node
dtb: xgene: Add MDIO node
drivers: net: xgene: ethtool: Use phy_ethtool_gset and sset
drivers: net: xgene: Use exported functions
drivers: net: xgene: Enable MDIO driver
drivers: net: xgene: Add backward compatibility
drivers: net: phy: xgene: Add MDIO driver
...
Pull libata updates from Tejun Heo:
"libata saw quite a bit of activities in this cycle:
- SMR drive support still being worked on
- bug fixes and improvements to misc SCSI command emulation
- some low level driver updates"
* 'for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (39 commits)
libata-scsi: better style in ata_msense_*()
AHCI: Clear GHC.IS to prevent unexpectly asserting INTx
ata: sata_dwc_460ex: remove redundant dev_err call
ata: define ATA_PROT_* in terms of ATA_PROT_FLAG_*
libata: remove ATA_PROT_FLAG_DATA
libata: remove ata_is_nodata
ata: make lba_{28,48}_ok() use ATA_MAX_SECTORS{,_LBA48}
libata-scsi: minor cleanup for ata_scsi_zbc_out_xlat
libata-scsi: Fix ZBC management out command translation
libata-scsi: Fix translation of REPORT ZONES command
ata: Handle ATA NCQ NO-DATA commands correctly
libata-eh: decode all taskfile protocols
ata: fixup ATA_PROT_NODATA
libsas: use ata_is_ncq() and ata_has_dma() accessors
libata: use ata_is_ncq() accessors
libata: return boolean values from ata_is_*
libata-scsi: avoid repeated calculation of number of TRIM ranges
libata-scsi: reject WRITE SAME (16) with n_block that exceeds limit
libata-scsi: rename ata_msense_ctl_mode() to ata_msense_control()
libata-scsi: fix D_SENSE bit relection in control mode page
...
As of an earlier change in this series ("Documentation: mmc:
sdhci-of-arasan: Add ability to export card clock") the SDHCI driver
used on Rockchip SoCs can now expose its clock. Let's now specify that
the PHY can use it.
Letting the PHY get access to this clock means it can adjust
phyctrl_frqsel field appropriately. Although the Rockchip PHY appears
slightly different than the reference Arasan one, you can see that the
Arasan datasheet [1] had it defined as:
Select the frequency range of DLL operation:
3b'000 => 200MHz to 170 MHz
3b'001 => 170MHz to 140 MHz
3b'010 => 140MHz to 110 MHz
3b'011 => 110MHz to 80MHz
3b'100 => 80MHz to 50 MHz
3b'101 => 275Mhz to 250MHz
3b'110 => 250MHz to 225MHz
3b'111 => 225MHz to 200MHz
On the Rockchip version of the PHY we have less granularity but the idea
is the same.
[1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdf
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The usb-phy is fully enclosed in the general register files (GRF). Therefore as seen from the device-tree it shouldn't be a separate platform-device but instead a sub-device of the GRF - using the simply-mfd mechanism. As the usb-phy is part of the kernel for some releases now, we keep the old (and now deprecated) binding for compatibility purposes. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Device tree binding for new phy-da8xx-usb driver. Signed-off-by: David Lechner <david@lechnology.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The DT bindings document for the Tegra XUSB pad controller states that 'utmi' is one of the valid choices for the Tegra210 PHY node names and has child lanes named, 'utmi-0', 'utmi-1', 'utmi-2' and 'utmi-3'. However, neither the XUSB pad controller PHY driver or the actual Tegra210 bindings for the XUSB pad controller use these names. Instead both the driver and binding use the node name 'usb2' and for the child lanes use the names 'usb2-0', 'usb2-1', 'usb2-2' and 'usb2-3'. Given that the driver and binding are consistent with the naming, update the DT bindings documentation to match. Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Thierry Reding <treding@nvidia.com>
Add documentation for SATA PHY available in Broadcom's NSP SoC. Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org>
Binding doc for NS2 PCIe PHYs. Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com> Signed-off-by: Jon Mason <jonmason@broadcom.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>