Add device tree binding documentation details of msa
memory region for ath10k qmi client for SDM845/APQ8098
SoC into "qcom,ath10k.txt".

Signed-off-by: Govind Singh <govinds@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

'interrupt-parent' is often documented as part of define bindings, but
it is really outside the scope of a device binding. It's never required
in a given node as it is often inherited from a parent node. Or it can
be implicit if a parent node is an 'interrupt-controller' node. So
remove it from all the binding files.

Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>

Add device tree binding documentation details for wcn3990
wifi block present in Qualcomm SDM845/APQ8098 SoC into
"qcom,ath10k.txt".

Signed-off-by: Govind Singh <govinds@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath.git patches for 4.16. Major changes:

ath10k

* enable multiqueue support for all hw using mac80211 wake_tx_queue op

* new Kconfig option ATH10K_SPECTRAL to save RAM

* show tx stats on QCA9880

* new qcom,ath10k-calibration-variant DT entry

* WMI layer support for wcn3990

ath9k

* new Kconfig option ATH9K_COMMON_SPECTRAL to save RAM

wcn36xx

* hardware scan offload support

wil6210

* run-time PM support when interface is down

The bus + bmi-chip-id + bmi-board-id is not enough to identify the correct
board data file on QCA4019 based devices. Multiple different boards share
the same values. Only the original reference designs can currently be
identified and loaded from the board-2.bin. But these will not result in
the correct calibration data when combined with the pre-calibration data
from the device.

An additional "variant" information has to be provided (via SMBIOS or DT)
to select the correct board data for a design which was modified by an ODM.

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Add documentation describing how device tree can be used to configure
wireless chips supported by the mt76 driver.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Improve the binding example by removing all the leading zeros to fix the
following dtc warnings:

Warning (unit_address_format): Node /XXX unit name should not have leading 0s

Converted using the following command:

perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find ./Documentation/devicetree/bindings "*.txt"`

Some unnecessary changes were manually fixed.

Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>

Pretty much any node can have a status property, so it doesn't need to
be in examples.

Converted with the following command and removed examples with SoC and
board specific splits:

git grep -l -E 'status.*=.*' Documentation/devicetree/ | xargs sed -i -E '/\sstatus.*=.*"(disabled|ok|okay)/d'

Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>

Pull DeviceTree updates from Rob Herring:

 - vsprintf format specifier %pOF for device_node's. This will enable us
   to stop storing the full node names. Conversion of users will happen
   next cycle.

 - Update documentation to point to DT specification instead of ePAPR.

 - Split out graph and property functions to a separate file.

 - New of-graph functions for ALSA

 - Add vendor prefixes for RISC-V, Linksys, iWave Systems, Roofull,
   Itead, and BananaPi.

 - Improve dtx_diff utility filename printing.

* tag 'devicetree-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (32 commits)
  of: document /sys/firmware/fdt
  dt-bindings: Add RISC-V vendor prefix
  vsprintf: Add %p extension "%pOF" for device tree
  of: find_node_by_full_name rewrite to compare each level
  of: use kbasename instead of open coding
  dt-bindings: thermal: add file extension to brcm,ns-thermal
  of: update ePAPR references to point to Devicetree Specification
  scripts/dtc: dtx_diff - Show real file names in diff header
  of: detect invalid phandle in overlay
  of: be consistent in form of file mode
  of: make __of_attach_node() static
  of: address.c header comment typo
  of: fdt.c header comment typo
  of: make of_fdt_is_compatible() static
  dt-bindings: display-timing.txt convert non-ascii characters to ascii
  Documentation: remove overlay-notes reference to non-existent file
  dt-bindings: usb: exynos-usb: Add missing required VDD properties
  dt-bindings: Add vendor prefix for Linksys
  MAINTAINERS: add device tree ABI documentation file
  of: Add vendor prefix for iWave Systems Technologies Pvt. Ltd
  ...

Motorola Droid 4 uses a WL 1285C. With differences between
chips not being public let's add explicit binding for wl1285
instead of relying on wl1283 being very similar.

Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>