linux.git/Documentation/devicetree/bindings/mtd, branch v4.13

Merge tag 'for-linus-20170713' of git://git.infradead.org/linux-mtd

2017-07-13T19:07:44+00:00

Pull MTD updates from Brian Norris:
 "General updates:
   - Cleanups and additional flash support for "dataflash" driver
   - new driver for mchp23k256 SPI SRAM device
   - improve handling of MTDs without eraseblocks (i.e., MTD_NO_ERASE)
   - refactor and improve "sub-partition" handling with TRX partition
     parser; partitions can now be created as sub-partitions of another
     partition

  SPINOR updates, from Cyrille Pitchen and Marek Vasut:
   - introduce support to the SPI 1-2-2 and 1-4-4 protocols.
   - introduce support to the Double Data Rate (DDR) mode.
   - introduce support to the Octo SPI protocols.
   - add support to new memory parts for Spansion, Macronix and Winbond.
   - add fixes for the Aspeed, STM32 and Cadence QSPI controler drivers.
   - clean up the st_spi_fsm driver.

  NAND updates, from Boris Brezillon:
   - addition of on-die ECC support to Micron driver
   - addition of helpers to help drivers choose most appropriate ECC
     settings
   - deletion of dead-code (cached programming and ->errstat() hook)
   - make sure drivers that do not support the SET/GET FEATURES command
     return ENOTSUPP use a dummy ->set/get_features implementation
     returning -ENOTSUPP (required for Micron on-die ECC)
   - change the semantic of ecc->write_page() for drivers setting the
     NAND_ECC_CUSTOM_PAGE_ACCESS flag
   - support exiting 'GET STATUS' command in default ->cmdfunc()
     implementations
   - change the prototype of ->setup_data_interface()

  A bunch of driver related changes:
   - various cleanup, fixes and improvements of the MTK driver
   - OMAP DT bindings fixes
   - support for ->setup_data_interface() in the fsmc driver
   - support for imx7 in the gpmi driver
   - finalization of the denali driver rework (thanks to Masahiro for
     the work he's done on this driver)
   - fix "bitflips in erased pages" handling in the ifc driver
   - addition of PM ops and dynamic timing configuration to the atmel
     driver"

* tag 'for-linus-20170713' of git://git.infradead.org/linux-mtd: (118 commits)
  Documentation: ABI: mtd: describe "offset" more precisely
  mtd: Fix check in mtd_unpoint()
  mtd: nand: mtk: release lock on error path
  mtd: st_spi_fsm: remove SPINOR_OP_RDSR2 and use SPINOR_OP_RDCR instead
  mtd: spi-nor: cqspi: remove duplicate const
  mtd: spi-nor: Add support for Spansion S25FL064L
  mtd: spi-nor: Add support for mx66u51235f
  mtd: nand: mtk: add ->setup_data_interface() hook
  mtd: nand: mtk: remove unneeded mtk_ecc_hw_init from mtk_ecc_resume
  mtd: nand: mtk: remove unneeded mtk_nfc_hw_init from mtk_nfc_resume
  mtd: nand: mtk: disable ecc irq when writing page with hwecc
  mtd: nand: mtk: fix incorrect register setting order about ecc irq
  mtd: partitions: fixup some allocate_partition() whitespace
  mtd: parsers: trx: fix pr_err format for printing offset
  MAINTAINERS: Update SPI NOR subsystem git repositories
  mtd: extract TRX parser out of bcm47xxpart into a separated module
  mtd: partitions: add support for partition parsers
  mtd: partitions: add support for subpartitions
  mtd: partitions: rename "master" to the "parent" where appropriate
  mtd: partitions: remove sysfs files when deleting all master's partitions
  ...

Merge tag 'nand/for-4.13' into MTD

2017-07-08T01:03:11+00:00

From Boris:
"""
This pull request contains the following core changes:

* addition of on-ecc support to Micron driver
* addition of helpers to help drivers choose most appropriate ECC
  settings
* deletion of dead-code (cached programming and ->errstat() hook)
* make sure drivers that do not support the SET/GET FEATURES command
  return ENOTSUPP use a dummy ->set/get_features implementation
  returning -ENOTSUPP (required for Micron on-die ECC)
* change the semantic of ecc->write_page() for drivers setting the
  NAND_ECC_CUSTOM_PAGE_ACCESS flag
* support exiting 'GET STATUS' command in default ->cmdfunc()
  implementations
* change the prototype of ->setup_data_interface()

A bunch of driver related changes:

* various cleanup, fixes and improvements of the MTK driver
* OMAP DT bindings fixes
* support for ->setup_data_interface() in the fsmc driver
* support for imx7 in the gpmi driver
* finalization of the denali driver rework (thanks to Masahiro for the
  work he's done on this driver)
* fix "bitflips in erased pages" handling in the ifc driver
* addition of PM ops and dynamic timing configuration to the atmel
  driver

And as usual we also have a few minor cleanup/fixes/improvements
patches across the subsystem.
"""

dt-bindings: gpmc: Correct location of generic gpmc binding

2017-06-22T19:12:15+00:00

The binding bus/ti-gpmc.txt has been moved to
memory-controllers/omap-gpmc.txt.  Update all references to this in
order to make reading and understanding a given binding easier.

Cc: David Woodhouse 
Cc: Brian Norris 
Cc:Boris Brezillon 
Cc: Marek Vasut 
Cc: Richard Weinberger 
Cc: Cyrille Pitchen 
Cc: Rob Herring 
Cc: Mark Rutland 
Signed-off-by: Tom Rini 
Signed-off-by: Boris Brezillon

dt-bindings: mtd: elm: Correct compatible string requirement

2017-06-22T19:10:47+00:00

The binding says that the compatible string must be "ti,am33xx-elm"
but the code checks only for, and all functioning users set, this as
"ti,am3352-elm" so correct the binding.

Cc: David Woodhouse 
Cc: Brian Norris 
Cc: Boris Brezillon 
Cc: Marek Vasut 
Cc: Richard Weinberger 
Cc: Cyrille Pitchen 
Cc: Rob Herring 
Cc: Mark Rutland 
Signed-off-by: Tom Rini 
Signed-off-by: Boris Brezillon

dt-bindings: mtd: make partitions doc a bit more generic

2017-06-20T19:59:11+00:00

Currently the only documented partitioning is "fixed-partitions" but
there are more methods in use that we may want to support in the future.
Mention them and make it clear Fixed Partitions are just a single case.

Signed-off-by: Brian Norris 
Signed-off-by: Rafał Miłecki 
Acked-by: Rob Herring

mtd: nand: denali_dt: add compatible strings for UniPhier SoC variants

2017-06-10T11:40:29+00:00

Add two compatible strings for UniPhier SoC family.

"socionext,uniphier-denali-nand-v5a" is used on UniPhier sLD3, LD4,
Pro4, sLD8.

"socionext,uniphier-denali-nand-v5b" is used on UniPhier Pro5, PXs2,
LD6b, LD11, LD20.

Signed-off-by: Masahiro Yamada 
Acked-by: Rob Herring 
Signed-off-by: Boris Brezillon

mtd: nand: denali: avoid hard-coding ECC step, strength, bytes

2017-06-10T11:40:13+00:00

This driver was originally written for the Intel MRST platform with
several platform-specific parameters hard-coded.

Currently, the ECC settings are hard-coded as follows:

  #define ECC_SECTOR_SIZE 512
  #define ECC_8BITS       14
  #define ECC_15BITS      26

Therefore, the driver can only support two cases.
 - ecc.size = 512, ecc.strength = 8    --> ecc.bytes = 14
 - ecc.size = 512, ecc.strength = 15   --> ecc.bytes = 26

However, these are actually customizable parameters, for example,
UniPhier platform supports the following:

 - ecc.size = 1024, ecc.strength = 8   --> ecc.bytes = 14
 - ecc.size = 1024, ecc.strength = 16  --> ecc.bytes = 28
 - ecc.size = 1024, ecc.strength = 24  --> ecc.bytes = 42

So, we need to handle the ECC parameters in a more generic manner.
Fortunately, the Denali User's Guide explains how to calculate the
ecc.bytes.  The formula is:

  ecc.bytes = 2 * CEIL(13 * ecc.strength / 16)  (for ecc.size = 512)
  ecc.bytes = 2 * CEIL(14 * ecc.strength / 16)  (for ecc.size = 1024)

For DT platforms, it would be reasonable to allow DT to specify ECC
strength by either "nand-ecc-strength" or "nand-ecc-maximize".  If
none of them is specified, the driver will try to meet the chip's ECC
requirement.

For PCI platforms, the max ECC strength is used to keep the original
behavior.

Newer versions of this IP need ecc.size and ecc.steps explicitly
set up via the following registers:
  CFG_DATA_BLOCK_SIZE       (0x6b0)
  CFG_LAST_DATA_BLOCK_SIZE  (0x6c0)
  CFG_NUM_DATA_BLOCKS       (0x6d0)

For older IP versions, write accesses to these registers are just
ignored.

Signed-off-by: Masahiro Yamada 
Acked-by: Rob Herring 
Signed-off-by: Boris Brezillon

mtd: mchp23k256: Add support for mchp23lcv1024

2017-06-08T23:32:11+00:00

The mchp23lcv1024 is similar to the mchp23k256, the differences (from a
software point of view) are the capacity of the chip and the size of the
addresses used.

There is no way to detect the specific chip so we must be told via a
Device Tree or default to mchp23k256 when device tree is not used.

Signed-off-by: Chris Packham 
Reviewed-by: Andrew Lunn 
Acked-by: Rob Herring 
Signed-off-by: Brian Norris

mtd: mchp23k256: Add OF device ID table

2017-06-01T18:28:53+00:00

This allows registering of this device via a Device Tree.

Signed-off-by: Chris Packham 
Reviewed-by: Andrew Lunn 
Tested-by: Andrew Lunn 
Acked-by: Boris Brezillon 
Acked-by: Rob Herring 
Signed-off-by: Brian Norris

mtd: nand: mediatek: update DT bindings

2017-06-01T08:09:36+00:00

Add MT2712 NAND Flash Controller dt bindings documentation.

Signed-off-by: Xiaolei Li 
Reviewed-by: Matthias Brugger 
Signed-off-by: Boris Brezillon