For v3.14 and prior, 1-bit Hamming code ECC via software was the
default choice for some boards e.g. 3430sdp.
Commit ac65caf514ec in v3.15 changed the behaviour
to use 1-bit Hamming code via Hardware using a different ECC layout
i.e. (ROM code layout) than what is used by software ECC.

This ECC layout change causes NAND filesystems created in v3.14
and prior to be unusable in v3.15 and later. So don't mark "sw" scheme
as deperecated and support it.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

With a flash-based BBT there is no reason to move the Factory Bad
Block Marker from the data area buffer (to where it is mapped by the
GPMI NAND controller) to the OOB buffer. Thus, make this feature
configurable via DT. This is required for the Ka-Ro electronics
platforms.

In the original code 'this->swap_block_mark' was synonymous with
'!GPMI_IS_MX23()', so use the latter at the relevant places.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Pull MTD updates from Brian Norris:
 - refactor m25p80.c driver for use as a general SPI NOR framework for
   other drivers which may speak to SPI NOR flash without providing full
   SPI support (i.e., not part of drivers/spi/)
 - new Freescale QuadSPI driver (utilizing new SPI NOR framework)
 - updates for the STMicro "FSM" SPI NOR driver
 - fix sync/flush behavior on mtd_blkdevs
 - fixup subpage write support on a few NAND drivers
 - correct the MTD OOB test for odd-sized OOB areas
 - add BCH-16 support for OMAP NAND
 - fix warnings and trivial refactoring
 - utilize new ECC DT bindings in pxa3xx NAND driver
 - new LPDDR NVM driver
 - address a few assorted bugs caught by Coverity
 - add new imx6sx support for GPMI NAND
 - use a bounce buffer for NAND when non-DMA-able buffers are used

* tag 'for-linus-20140610' of git://git.infradead.org/linux-mtd: (77 commits)
  mtd: gpmi: add gpmi support for imx6sx
  mtd: maps: remove check for CONFIG_MTD_SUPERH_RESERVE
  mtd: bf5xx_nand: use the managed version of kzalloc
  mtd: pxa3xx_nand: make the driver work on big-endian systems
  mtd: nand: omap: fix omap_calculate_ecc_bch() for-loop error
  mtd: nand: r852: correct write_buf loop bounds
  mtd: nand_bbt: handle error case for nand_create_badblock_pattern()
  mtd: nand_bbt: remove unused variable
  mtd: maps: sc520cdp: fix warnings
  mtd: slram: fix unused variable warning
  mtd: pfow: remove unused variable
  mtd: lpddr: fix Kconfig dependency, for I/O accessors
  mtd: nand: pxa3xx: Add supported ECC strength and step size to the DT binding
  mtd: nand: pxa3xx: Use ECC strength and step size devicetree binding
  mtd: nand: pxa3xx: Clean pxa_ecc_init() error handling
  mtd: nand: Warn the user if the selected ECC strength is too weak
  mtd: nand: omap: Documentation: How to select correct ECC scheme for your device ?
  mtd: nand: omap: add support for BCH16_ECC - NAND driver updates
  mtd: nand: omap: add support for BCH16_ECC - ELM driver updates
  mtd: nand: omap: add support for BCH16_ECC - GPMC driver updates
  ...

Pull trivial tree changes from Jiri Kosina:
 "Usual pile of patches from trivial tree that make the world go round"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
  staging: go7007: remove reference to CONFIG_KMOD
  aic7xxx: Remove obsolete preprocessor define
  of: dma: doc fixes
  doc: fix incorrect formula to calculate CommitLimit value
  doc: Note need of bc in the kernel build from 3.10 onwards
  mm: Fix printk typo in dmapool.c
  modpost: Fix comment typo "Modules.symvers"
  Kconfig.debug: Grammar s/addition/additional/
  wimax: Spelling s/than/that/, wording s/destinatary/recipient/
  aic7xxx: Spelling s/termnation/termination/
  arm64: mm: Remove superfluous "the" in comment
  of: Spelling s/anonymouns/anonymous/
  dma: imx-sdma: Spelling s/determnine/determine/
  ath10k: Improve grammar in comments
  ath6kl: Spelling s/determnine/determine/
  of: Improve grammar for of_alias_get_id() documentation
  drm/exynos: Spelling s/contro/control/
  radio-bcm2048.c: fix wrong overflow check
  doc: printk-formats: do not mention casts for u64/s64
  doc: spelling error changes
  ...

This commit updates the devicetree binding documentation for this driver
with the supported ECC strength and step size combinations.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

- Adds DT binding property for BCH16 ECC scheme
 - Adds describes on factors which determine choice of ECC scheme for particular device

CC: devicetree@vger.kernel.org
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The m25p80.c has used the SPI NOR framework now, and the m25p_ids has
been moved to spi-nor.c and renamed to spi_nor_ids.

This patch updates the document for m25p80.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Fixed multiple spelling errors.

Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Carlos E. Garcia <carlos@cgarcia.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

This patch adds the binding file for Freescale QuadSPI driver.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Cc: devicetree@vger.kernel.org
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>