linux.git/Documentation/devicetree/bindings/input/touchscreen, branch v4.15

dt-bindings: Remove leading 0x from bindings notation

2017-12-06T20:56:33+00:00

Improve the binding example by removing all the leading 0x to fix the
following dtc warnings:

Warning (unit_address_format): Node /XXX unit name should not have leading "0x"

Converted using the following command:

find Documentation/devicetree/bindings -name "*.txt" -exec sed -i -e 's/([^ ])\@0x([0-9a-f])/$1\@$2/g' {} +

This is a follow up to commit 48c926cd3414

Signed-off-by: Mathieu Malaterre 
Signed-off-by: Rob Herring

Merge tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux

2017-11-15T02:25:40+00:00

Pull DeviceTree updates from Rob Herring:
 "A bigger diffstat than usual with the kbuild changes and a tree wide
  fix in the binding documentation.

  Summary:

   - kbuild cleanups and improvements for dtbs

   - Code clean-up of overlay code and fixing for some long standing
     memory leak and race condition in applying overlays

   - Improvements to DT memory usage making sysfs/kobjects optional and
     skipping unflattening of disabled nodes. This is part of kernel
     tinification efforts.

   - Final piece of removing storing the full path for every DT node.
     The prerequisite conversion of printk's to use device_node format
     specifier happened in 4.14.

   - Sync with current upstream dtc. This brings additional checks to
     dtb compiling.

   - Binding doc tree wide removal of leading 0s from examples

   - RTC binding documentation adding missing devices and some
     consolidation of duplicated bindings

   - Vendor prefix documentation for nutsboard, Silicon Storage
     Technology, shimafuji, Tecon Microprocessor Technologies, DH
     electronics GmbH, Opal Kelly, and Next Thing"

* tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
  dt-bindings: usb: add #phy-cells to usb-nop-xceiv
  dt-bindings: Remove leading zeros from bindings notation
  kbuild: handle dtb-y and CONFIG_OF_ALL_DTBS natively in Makefile.lib
  MIPS: dts: remove bogus bcm96358nb4ser.dtb from dtb-y entry
  kbuild: clean up *.dtb and *.dtb.S patterns from top-level Makefile
  .gitignore: move *.dtb and *.dtb.S patterns to the top-level .gitignore
  .gitignore: sort normal pattern rules alphabetically
  dt-bindings: add vendor prefix for Next Thing Co.
  scripts/dtc: Update to upstream version v1.4.5-6-gc1e55a5513e9
  of: dynamic: fix memory leak related to properties of __of_node_dup
  of: overlay: make pr_err() string unique
  of: overlay: pr_err from return NOTIFY_OK to overlay apply/remove
  of: overlay: remove unneeded check for NULL kbasename()
  of: overlay: remove a dependency on device node full_name
  of: overlay: simplify applying symbols from an overlay
  of: overlay: avoid race condition between applying multiple overlays
  of: overlay: loosen overly strict phandle clash check
  of: overlay: expand check of whether overlay changeset can be removed
  of: overlay: detect cases where device tree may become corrupt
  of: overlay: minor restructuring
  ...

Input: add support for the Samsung S6SY761 touchscreen

2017-11-10T18:18:23+00:00

The S6SY761 touchscreen is a capicitive multi-touch controller
for mobile use. It's connected with i2c at the address 0x48.

This commit provides a basic version of the driver which can
handle only initialization, touch events and power states.

The controller is controlled by a firmware which, in the version
I currently have, doesn't provide all the possible
functionalities mentioned in the datasheet.

Signed-off-by: Andi Shyti 
Acked-by: Rob Herring 
Signed-off-by: Dmitry Torokhov

Input: add support for HiDeep touchscreen

2017-11-10T18:18:22+00:00

The HiDeep touchscreen device is a capacitive multi-touch controller
mainly for multi-touch supported devices use. It use I2C interface for
communication to IC and provide axis X, Y, Z locations for ten finger
touch through input event interface to userspace.

It support the Crimson and the Lime two type IC. They are different
the number of channel supported and FW size. But the working protocol
is same.

Signed-off-by: Anthony Kim 
Acked-by: Rob Herring 
Signed-off-by: Dmitry Torokhov

dt-bindings: Remove leading zeros from bindings notation

2017-11-09T23:05:05+00:00

Improve the binding example by removing all the leading zeros to fix the
following dtc warnings:

Warning (unit_address_format): Node /XXX unit name should not have leading 0s

Converted using the following command:

perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find ./Documentation/devicetree/bindings "*.txt"`

Some unnecessary changes were manually fixed.

Signed-off-by: Marco Franchi 
Signed-off-by: Rob Herring

Input: add I2C attached EETI EXC3000 multi touch driver

2017-10-25T21:55:33+00:00

The 3000 series have a new protocol which allows to report up to 5 points
in a single 66 byte frame. One must always read in 66 byte frames.
To support up to 10 points, two consecutive frames need to be read:
The first frame says how many points until sync.
The second frame must say zero points or both frames must be discarded.

To be able to work with the higher 400KHz I2C bus rate, one must
successfully send a special package prior _each_ read or the controller
will refuse to cooperate.

This is a minimal implementation based on egalax_i2c.c (which can be found
on the internet) and egalax_ts.c but without the vendor interface and no
power management support.

Signed-off-by: Ahmet Inan 
Acked-by: Rob Herring 
Signed-off-by: Dmitry Torokhov

Input: goodix - support gt1151 touchpanel

2017-10-24T18:58:19+00:00

Support was added based on Goodix GitHub repo [1]. There are two major
differences between gt1151 and currently supported devices (gt9x):
 * CONFIG_DATA register has 0x8050 address instead of 0x8047,
 * config data checksum has 16-bit width instead of 8-bit.

Also update goodix_i2c_test() function, so it reads ID register (which
has the same address for all devices) instead of CONFIG_DATA (because
its address is known only after reading ID of the device).

[1] https://github.com/goodix/gt1x_driver_generic

Signed-off-by: Marcin Niestroj 
Acked-by: Rob Herring 
Signed-off-by: Dmitry Torokhov

dt-bindings: Remove "status" from examples

2017-09-05T15:03:06+00:00

Pretty much any node can have a status property, so it doesn't need to
be in examples.

Converted with the following command and removed examples with SoC and
board specific splits:

git grep -l -E 'status.*=.*' Documentation/devicetree/ | xargs sed -i -E '/\sstatus.*=.*"(disabled|ok|okay)/d'

Acked-by: Mark Rutland 
Signed-off-by: Rob Herring

Input: add support for the STMicroelectronics FingerTip touchscreen

2017-06-05T22:35:34+00:00

The stmfts (ST-Microelectronics FingerTip S) touchscreen device is a
capacitive multi-touch controller mainly for mobile use.  It's connected
through i2c bus at the address 0x49 and it interfaces with userspace
through input event interface.

At the current state it provides a touchscreen multitouch functionality up
to 10 fingers. Each finger is enumerated with a distinctive id (from 0 to
9).

If enabled the device can support single "touch" hovering, by providing
three coordinates, x, y and distance.

It is possible to select the touchkey functionality which provides a basic
two keys interface for "home" and "back" menu, typical in mobile phones.

Signed-off-by: Andi Shyti 
Reviewed-by: Javier Martinez Canillas 
Acked-by: Rob Herring 
Signed-off-by: Dmitry Torokhov

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

2017-05-26T23:45:13+00:00

Pull input layer fixes from Dmitry Torokhov:
 "Just a few fixups to a couple of drivers"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: elan_i2c - ignore signals when finishing updating firmware
  Input: elan_i2c - clear INT before resetting controller
  Input: atmel_mxt_ts - add T100 as a readable object
  Input: edt-ft5x06 - increase allowed data range for threshold parameter