There was a spelling mistake on TSC/ADC binding where "coordinate" was
spelled as "coordiante".

We can't simply fix the error due to DT being an ABI, the approach taken
was to first use correct spelling and if that fails, fall back to
miss-spelled version.

It's unfortunate that has creeped into the tree.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Merge with mainline to bring in sync changes to cyttsp4 driver.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This patch adds DT support to touch driver. It also provides a binding
document which is used by the MFD and IIO part of the device.
This patch also renames steps_to_configure to coordinate_readouts
because the original name misleads the purpose of the variable.

Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>

We add the possibility to hand over a GPIO number for the reset pin.
This way we can remove existing board code that takes care of it and
group this information properly in the platform data or in the device
tree configuration.

Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Merge with mainline to bring in module_platform_driver_probe() and
devm_ioremap_resource().

Add the necessary code to create the needed platformdata from devicetree
informations.

The interrupt mode of the chip is not set via devicetree, as it is not
a property of the hardware but instead only a preferred type of operation.
This should probably be made settable via configfs in the future.
The option set as default is the mode the datasheet mentions as default.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Pull second round of input updates from Dmitry Torokhov:
 "As usual, there are a couple of new drivers, input core now supports
  managed input devices (devres), a slew of drivers now have device tree
  support and a bunch of fixes and cleanups."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (71 commits)
  Input: walkera0701 - fix crash on startup
  Input: matrix-keymap - provide a proper module license
  Input: gpio_keys_polled - switch to using gpio_request_one()
  Input: gpio_keys - switch to using gpio_request_one()
  Input: wacom - fix touch support for Bamboo Fun CTH-461
  Input: xpad - add a few new VID/PID combinations
  Input: xpad - minor formatting fixes
  Input: gpio-keys-polled - honor 'autorepeat' setting in platform data
  Input: tca8418-keypad - switch to using managed resources
  Input: tca8418_keypad - increase severity of failures in probe()
  Input: tca8418_keypad - move device ID tables closer to where they are used
  Input: tca8418_keypad - use dev_get_platdata() to retrieve platform data
  Input: tca8418_keypad - use a temporary variable for parent device
  Input: tca8418_keypad - add support for shared interrupt
  Input: tca8418_keypad - add support for device tree bindings
  Input: remove Compaq iPAQ H3600 (Bitsy) touchscreen driver
  Input: bu21013_ts - add support for Device Tree booting
  Input: bu21013_ts - move GPIO init and exit functions into the driver
  Input: bu21013_ts - request regulator that actually exists
  ARM: ux500: Strip out duplicate touch screen platform information
  ...

This patch allows the STMPE Touchscreen driver to be successfully probed and
initialised when Device Tree support is enabled. Bindings are mentioned in
Documentation too.

Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Linux 3.7-rc4