Since there are no registers controlling the hardware parameters
IC_CAP_LOADING and IC_CLK_FREQ_OPTIMIZATION, their values can only be
declared in the device tree.

snps,bus-capacitance-pf indicates the bus capacitance in picofarads (pF).
It affects the high and low pulse width of SCL line in high speed mode.
The legal values for this property are 100 and 400 only, and default
value is 100. This property corresponds to IC_CAP_LOADING.

snps,clk-freq-optimized indicates whether the hardware reduce its
internal clock frequency by reducing the internal latency required to
generate the high period and low period of SCL line. This property
corresponds to IC_CLK_FREQ_OPTIMIZATION.

The driver can calculate the high period count and low period count of
SCL line for high speed mode based on these two properties.

Signed-off-by: Michael Wu <michael.wu@kneron.us>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

Hardware is not limited to 400kHz, its documentation does mention how to
configure it for high-speed (a specific Speed-Mode enum value and
a different bus rate clock divider register to be used).

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

After EyeQ5, it is time for Mobileye EyeQ6H to reuse the Nomadik I2C
controller. Add a specific compatible because its HW integration is
slightly different from EyeQ5.

Do NOT add an example as it looks like EyeQ5 from a DT standpoint
(without the mobileye,olb property).

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

The I2C controller IP used in the Allwinner A523/T527 SoCs is
compatible with the ones used in the other recent Allwinner SoCs.

Add the A523 specific compatible string to the list of existing names
falling back to the allwinner,sun8i-v536-i2c string.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

Add dt-schema for the I2C controller on the RTL9300 Ethernet switch
with integrated SoC.

Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

S32G2 and S32G3 SoCs use the same I2C controller as i.MX.
But there are small differences such as specific
<clock divider, register value> pairs.
So add new compatible strings 'nxp,s32g2-i2c'and 'nxp,s32g3-i2c'
for S32G2/S32G3 Socs.

Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

PIC64GX i2c is compatible with the microchip corei2c, just add fallback

Signed-off-by: Pierre-Henry Moussay <pierre-henry.moussay@microchip.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

The CCI on the Snapdragon 670 is the interface for controlling camera
hardware over I2C. Add the compatible so it can be added to the SDM670
device tree.

Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

Convert the Spreadtrum SC9860 I2C controller bindings to DT schema.
Adjust filename to match compatible.

Signed-off-by: Stanislav Jakubek <stano.jakubek@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>

Theobroma Systems Mule is an MCU that emulates a set of I2C devices,
among which devices that are reachable through an I2C-mux. The devices
on the mux can be selected by writing the appropriate device number to
an I2C config register.

Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Farouk Bouabid <farouk.bouabid@cherry.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>